Loading ...
Loading ...
Loading ...
Step-by-step installation instructions.
Programming the Control
CONTROL SETTINGS REQUIRED upon installation and
alter an extended power outage.
NOTES:
::Ji::X4_HEN THE T1L_tNSFORMER IS PI,UGGED INTO THE
EI,ECTRI(:AI, OUTI,ET, 12:00 PM (flashing), and PRESENT
TIME is displayed. Program tile control as instructed bel_m'.
If __--I_-- -is flashing, use tile Up • button to set tile
correct model code as fi)llo_vs: S1_2 fin" GXSF27E. If wm
pass by tile correct code nmnbe_; use tile DOWN • i)utton.
Then press the MODEbutton to accept the correct model.
_: A "beep" sounds while pressing buttons tor control
programming. One beep signals a change in the control
display: Repeated beeps mean tile control will not accept
a change ti'om tile button you have pressed, and you should
select another button.
::Ji::To program tile control, p)/i will tlse tile UP •, DOWN •
and MOOEbuttons.
_: Use the MODEbutton to select the desired control fimction.
SETPRESENTTIME OFDAY
I. Press tile MODEbutton until PRESENT
TIMEappeax_ in tile display.
2.Press Lrp • or DOWN • button to set.
The UP button ad\m_ces tile time; tile
DOWN button inoves tile time in i'eveiNe.
_PM
U.CO
I'JO
PRESeNT'ME
I !.-IF'_
v30
PRESENT_M_
If tile present time is between noon and midnight, be sure
PM sho_vs in the display. If the present time is between
midnight and noon, be sure _] shows in tile display:
NOTE:Each press of an UP • or DOWN • button changes
the time bv one minute. Holding the button changes the time
at a rapid rate.
3. \_]/en the present time is correct, press MODE to accept.
SET WATERHARDNESSNUMBER
I. Pressthe MODEbutton until
HARDNESSappeax_in the display.
2. Press UP • or DO_VN • button to set your water hardness
nmnber in tile display. DOWN decreases tile hardness xdue.
UP increases tile hardness xdue.
NOTE'Each press of a button changes tile display by 1, between
1 and 25. Above 25, the display changes 5 at a time (25, 30, 35,
etc.). Holding a button in changes tile nulnbei_ at a rapid rate.
3. When the display sho_vs yore" water hardness (in grains per
gallon), press MODEm accept.
NOTE."If there is dear water iron in your water supply, you will
need to increase the haacd_mss setting by 5 for each 1 ppm of
clear water iron in your water supply.
You cm_ get the grains per gallon (gpg) haacd_mss of your water
supply from a water m_aJysis laboratory. If you are on a
municipal supply, call your local water department. Or call
Legend Tecl_fical Services, an independent laboratory, to
request a water haaxlness test kit at 1.800.826.8553, extension
47. If your report shows hamd_mss in parts per million (ppm)
or milligrmns per liter (rag/l), shnply divide by 17.1 to get the
equivalent nmnber of grains per gallon.
SETRECHARGE(STARTING)TIME
I
-_Hn
I-t
AM
I. Press the MODE button until l _£_E!IjRECHARGETIMEappea_ in tile display.
NOTE.'A flashing 2:00 _/I (ii_cto_y delimit)
shouM show in the display: This is a good time tot recharge
to start (takes about 2 houi_) in most households because water
is not in use. HARD X_;_TER is b}passed to house tinlcets
dm-ing rechmge.
If no chm_ge is needed, go to step 3. To change the rechmge
starting time, tollow step 2.
2.Press UP • or DOX4'N • button to set tile desired rechaxge
start time. Be sure to observe tile f_dVIor PM as w)u did when
setfng the time ot day,
NOTE.'Each press of a button changes tile time by l horn;
Holding tile buttons in changes tile time at a rapid rate.
3. Press the MODE button to accept.
8
Loading ...
Loading ...
Loading ...