Loading ...
Loading ...
Loading ...
6
chopping. The Pulse mode is also effective in
starting the blending process when you do not
want continuous power or when processing
items that do not require an extended amount
of blending.
WARNING: FLASHING RED LIGHT INDICATES
READY TO OPERATE. DO NOT TOUCH BLADES.
5. To pause or stop blending process:
a. To pause blending process:
Push the button corresponding to the speed at
which you are currently blending. For example:
If you are blending on High speed, push the
High speed button and the blender will stop
blending, but the unit will remain on.
b. To stop blending process:
Push the On/Off button when you are finished
with your recipe and would like to turn the
blender off.
c. To prevent excessive stress to the motor:
Your blender incorporates an auto-stop
feature. After running continuously for two
minutes, the blender will automatically revert to
Standby mode. To continue blending, press the
desired function.
To dislodge food: First, be sure blender is turned
off. Use a rubber or plastic spatula to help remove
food lodged around the removable blade assem-
bly. Replace the cover and measured pour lid and
continue blending, if necessary. Make sure spatula
is not inside the blender jar before blending.
To reset the unit: This appliance features an
advanced, resettable thermal device. In the event
of an overload condition, the unit will shut down
to protect the motor from overheating. To reset
the appliance when this happens, unplug the unit
and let it cool for a minimum of 15 minutes. Then,
reduce the contents of the blender jar and/or clear
any jams. Restart the unit as noted in the operat-
ing directions.
When finished blending: Press the On/Off but-
ton and unplug the blender from the electrical
outlet. Never remove the blender jar from the
motor base until the blender is off. Do not remove
blade assembly from blender jar when removing
jar from motor base. Simply lift blender jar from
motor base. Do not put hands into blender jar with
blender plugged in.
CLEANING AND MAINTENANCE
OF CUISINART
®
VELOCITY Ultra
Trio 1 HP BLENDER
Always unplug your Cuisinart
®
VELOCITY Ultra Trio 1
HP Blender from the electrical outlet before cleaning.
The blender is made of corrosion-resistant parts that
are easy to clean. Before first use and after every
use, clean each part thoroughly. Periodically check
all parts before reassembly. If any part is damaged
or blender jar is chipped or cracked, DO NOT USE
BLENDER.
Remove the blender jar from the motor base by lifting
straight up and away. Remove blade assembly by
turning counterclockwise.
Wash in warm, soapy water, rinse and dry thoroughly.
CAUTION: Handle the blade assembly carefully. It
is SHARP and may cause injury. Do not attempt to
remove blades from assembly.
Remove the blender jar cover and the measured
pour lid. Wash in warm, soapy water; rinse and dry
thoroughly or place in upper rack of dishwasher. The
blender jar must be washed in warm, soapy water
and rinsed and dried thoroughly. The blender jar can
also be placed upside down in dishwasher.
Finally, wipe the motor base clean with a damp cloth
to remove any residue and dry thoroughly. Never
submerge the motor base in water or other liquids,
or place in a dishwasher.
Tip: You may wish to clean your blender blade
assembly as follows: Squirt a small amount of
dishwashing liquid into assembled blender jar and
fill halfway with warm water. Run on Low for 15
seconds. Repeat, using clean tap water. Rinse and
dry all parts thoroughly.
Any other servicing should be performed by an
authorized service representative.
CLEANING AND STORING YOUR
CUISINART
®
VELOCITY Ultra Trio
1 HP BLENDER/FOOD
PROCESSOR WITH TRAVEL CUPS
Store the chopping blade and slicing/shredding disc as
you would sharp knives – out of the reach of children.
The work bowl, cover, pusher, chopping blade and slicing/
shredding disc are top-shelf dishwasher safe. When
placing parts in your dishwasher, insert the work bowl
upside down. Remember where you place the sharp blade
and disc, and be certain to unload the dishwasher
carefully.
The gearbox collar is not immersible. To clean, just wipe
with a damp cloth. If you wash the blades and discs by
hand, do it carefully. Avoid leaving them in soapy water
where they may disappear from sight. To clean the metal
blade, fill the work bowl with soapy water, hold the blade
Loading ...
Loading ...
Loading ...