Loading ...
Loading ...
Loading ...
TAPE COPYING
6 5
19 2107
The tape copying function permits you to copy the contents of a
tape in Deck t to e tape in Deck II
Tile Copy SPEED switch (NORM/HIGH} is used to select either
normal speed copying (to listen to playback as a tape is being
copied) or high speed copying (the tape is copied at twice normal
playback speed)
Press the EJECT/STOP button on Deck I to open the
cassette compartment door, insert a prerecorded tape
(tape to be copied), and close the door
Press the EJECT/STOP button on Deck 11 to open the
cassette compartment door, insert a recording tape, and
close the door
Press the appropriate DOLBY NR switches (OFF/B/C]
• This setting has no affect on the copying operation It affects
only the playback signal of the tape in Deck I for monitoring
during normal speed copying
Set the TAPE SELECTOR [] switches according to the
tape used in Deck II (See page 6 )
* Deck 1is equipped with an automatic tape selector function,
so this setting is made automatically for the tape in Deck t
Set the Reverse MODE switches appropriately,
{See page 4 )
• To copy both sides of a tope, set the Reverse MODE switch
of both Deck I and Deck II to the ( _ ) position
6
To start playback and recording in the direction opposite
to that shown by the tape direction indicators, press the
DIRECTION levers for each deck
• When the Reverse MODE switches are set to the { -_ }
position for copying of both sides of a tape, always start
ptayback and recording in the FWD direction. Load the tapes
so that the supply reel {full reel) is on the left side
• Playback and recording direction is cf_anged each time the
DiRECTiON lever is pressed
• If the COPY switch isON ( it ) at this point, the DIRECTION
_ever for Deck I will not function, Set the p_ayback d_tecgen
with the COPY switch in the OFF { _, ) position
Set the COPY switch to the ON ( It ) position
• The COPY indicator (_) will light
t2
<RRB-276>
9
1
Set the Copy SPEED selector to the NORM or HIGH poe}
tion,
NORM', Tape copying at normal speed for listening t_
playback
HIGH: Tape copying at twice normal speed
Press the PLAY button on Deck I,
Deck I will enter the PLAY stand-by mode, and playback wl
not start yet
Press the REC button on Deck II
• When the REC button an Deck It is pressed, the PLAY bc
ton on Deck tl will be engaged automatically, and copy#
will begin
NOTE DURtNG TAPE COPYING
• When repeating the tape copying, be sure to leave the original
tape in deck I Making a copy ore copy will resutt in a deteriora-
tion in sound quality
• When making tape copies, adjustment of the recording level is
not required
• Whanperformingtapecopying. besuretousetapesofthesame
length
• When performhrg tape copying, the copy wilt be produced with
the same noise reduction effects as those used on the original
tape. regardless of the position of the noise reduction switches
For e_ample, if the original tape was recorded with the Dolby C
noise reduction, the copy wig be produced with the same Dotby
C noise reduction effects
• tfatapeprerecordedatahighrecording/evelistoadedinDackl,
and an empty tape with a low saturation level is loaded in Deck II
for copying, the resulting sound may be distorted
• Do not change the ,SPEED swtich position during tape copying,
. When you wish to perform MUSIC SCAN (CUE or REVIEW) us-
ing Deck I while copying a tape, put Deck tt into the REC PAUSE
tREC stand.by) mode If you do not do this, noise may be
recorded
• The playback sound output from the LINE OUTPUT terminals
during eopythg is to enable you to check d_e COPY operation
Consequently. it may sometimes differ slightly from dTe original
sound
NOTE DURING HIGH-SPEED COPYING
When performing high-speed copying with this unit, ira television
is used nearby, a high.pitched mterference sound may be heard on
the recording fn tt_is case, either use the normat_speed copying
function, or turn off tlre power of the television
Loading ...
Loading ...
Loading ...