Loading ...
Loading ...
Loading ...
20 21
SAFETYMAINENTANCE
GET TO KNOW YOUR OVEN
Releasing the grill element – grill in oven and
separate grill models
help you reach your cavity roof for cleaning. To remove grill,
push sides of hanger clip in the direction of arrows until one
hanger clip can easily be removed from retaining hole.
To replace, reverse the process.
Grill in oven model shown. The grill element in separate
grill models has the same hanger clip arrangement in the
grill compartment.
Removing and replacing the oven light
Turn oven light glass anticlockwise to remove it for
globe replacement.
be used.
WARNING
Make sure the appliance is turned off before you remove or replace
parts, to avoid the possibility of electric shock.
Get to know your new oven with this ‘Simple
Test Cake’
Although we strive for a perfect performing oven,
when baking. Therefore, we suggest this simple, easy
understand your new oven. All ovens do sometimes have
hot or cold spots, therefore it is important to judge with
‘Simple Test Cake’
125g butter, softened to room temperature
1 cup caster sugar
1 teaspoon pure vanilla essence
4 large eggs
2 cups self-raising flour
pinch of salt
Method:
proof or baking paper.
and ensure oven shelf is in the centre position of oven.
4. Add vanilla essence.
5. Then eggs one at a time, beating well after each
addition.
well combined.
7. Add milk and beat or stir to combine.
35 minutes or until when tested with a fine cake skewer
it comes out clean or the edges of the cakes have come
away slightly from the sides of the cake pans.
10.Remove from oven to wire cake rack and rest for
completely.
To Serve: sandwich together with your favourite jam or
conserve, and dust top with pure icing sugar.
NOTE: if desired substitute butter for either margarine or
olive oil spread.
Recipe is based on the Australian standard metric
MAINTAINING YOUR APPLIANCE
Your gas oven is fitted with an electronic controller which
manages the operation of the burner and monitors the
flame. This controller includes features which ensure the safe
operation of your appliance and will prevent the build up
of unburnt gas, should a fault occur.
to maintain a stable temperature in the oven. The Thermostat
(indicator glows), or when the flame is off (indicator off).
The burner flame can be seen by viewing through the
2 holes in the front of the burner cover.
Ignition and Response to Ignition Failure
The controller will attempt to ignite the flame when an oven
function is selected and the Thermostat turns on (indicator
light changes from off to on). The controller will make up
to 2 attempts to ignite the flame, stopping if a flame is
a flame is not detected then the burner and ignition will be
turned off and a delay of 90 seconds will be observed.
Function and Thermostat controls.
At the end of this delay, switch the Thermostat or Function
re-attempt ignition.
ignition will not be attempted until the Thermostat or
Response to Flame Failure
controller will respond
of up to 3 attempts and
be shut off.
re-light the burner, stopping if a flame is detected by the
is not detected then the burner and ignition will be turned
this delay the controller will not respond to the Function and
Thermostat controls.
At the end of this delay, switch the Thermostat or Function
re-attempt ignition.
ignition will not be attempted until the Thermostat or
Recognising a Safety Shut-down Condition
when the burner flame is igniting or on, and the Thermostat
indicator light is off when the flame is off.
but the flame is not on or attempting to ignite then the
controller has invoked a safety shutdown of the burner.
A 90 second delay is observed from the time the shut-down
occurred before the controller will respond to the oven controls.
before oven functions can resume.
Power Failure
restoration of power will not cause the burner to ignite if the
controls were left on. However the grill element will resume
heating on models which do not have an electronic clock.
To resume operation of the appliance after a power
interruption:
the off position. The controls must remain in this position
for at least 5 seconds
f the appliance has an electronic clock then set the time
of day on the electronic clock.
Normal operation of the appliance may now resume.
ELECTRONIC BURNER CONTROL
Loading ...
Loading ...
Loading ...