Loading ...
Loading ...
Loading ...
WARNING
Do not cut down a tree during high or changing winds or if there is
a danger to propert_ Consult a tree professional
Do not cut down a tree if there is a danger of sthking utJlity wires;
notify the utility company before making any cuts.
GENERAL GUIDELINES FOR FELLING TREES:
Normally felling consists of 2 main cutting operations, notching (C)
and making tile felling cut (D).
Start making the upper notch cut (C) on the side of the tree facing
tile felling direction (E). Be sure you don't make the lower cut too
deep into the trunk.
The notch (C) should be deep enough to create a hinge (F) of suf-
ficient width and strength. The notch should be wide enough to
direct the fa_l of the tree for as long as possible.
WARNING
Never walk in front of a tree that has been notched.
E
Make the felling cut (D) from the other side of the tree and 1.5" - 2.0" (3-5cm) above the edge of the notch (C) (Figure
5-IB).
AVERTISSEMENT
Evger la coupe par mauvais temps, fort vent, vent changeant ou si cela peot endommager une propri6t& Consulter
un protessionnel du m_tie_
Ne pa$ oouper d'arbre s'iI y a une possibilit_ de heutter des fils _lectr_ques ou aotres. Pr_venir les services publics
appropri_$ av8_ toote coupe.
REGLES GENERALES A OBSERVER POUR L'ABATTAGE :
En principe, I'abatlage se divise en 2 operations: I'entaiIle (C) et le trait d'abattage (D).
Toujours commencer par le trait diagonal (du haut) de I'entaiIle d'abattage (C), du c6t_ choisi pour la chute de I'arbre
(E). Evitsr de scier trop profond_ment _'entaille horizonts_e (du bas).
L'eofaille d'abattage (C) dog 6tre suffisamment ouverte pour crier une chami&re (F) assez forte de largeur suffisante
et pour guider la chute de I'arbre aussi Iongtemps que possible.
AVERTISSEMENT
Ne jamais marcher devant un arbre entailI&
Scier le trait d'abattage (D) de I'aotre c6t6 du tronc, 3 _ 5 cm (1,5 _ 2,0") au-dessus de I'entaille d'abattage (C) (Figure
5-IB).
ADVERTENCIA
No corte un _rbol durante vientos r_pidos o cambiantes o si hay pe{igro para una propiedad. Consulte a un profe-
sionaI de _rboles.
NO corte un _rbol si hay peligro de que a_ambres de servicio sean golpeados; notifique a la compa_ia de servicio
antes de hacer cualquier cotte.
REGLAS GENERALES PARA EL TALADO DE ARBOLES:
Normalmente el talado consiste en 2 operaciones de corte principales, haciendo la ranura (C) y realizando el corte
de talado (D).
Empiece haciendo el cotte de ranura (C) superior en la parte del _rbol apuntando a la direcciSn de caida (E).
Asegt3rese de no hacer el corte inferior muy profundo dentro del tronco.
La ranura (C) deber_ ser Io bastante protunda para crear una atticulaci6n (F) de suflciente anchura y fuerza. La ranu-
ra deber_ ser Io suficiente ancha para dirigir la caida del _rbol por el mayor tiempo posthle.
ADVERTENCIA
Nunca camine en frente de un &rbor que haya sido ranurado.
Rea_ice el cotte de talado (D) desde la otra patte del _rbol y 3-5cm (1.5 - 2.0") argba del borde de la ranura (C) (Figura
5-IB).
26
Loading ...
Loading ...
Loading ...