Loading ...
Loading ...
Loading ...
SPECIFIC SAFETY INSTRUCTIONS
FOR THE DRILL PRESS
14.SECURE WORK. Usa clamps or viseto holdthe
work when practical.It'ssafer than using yourhand
and itfrees bothhandsto operatetool,
For yourownsafety,do nottry to use yourdrillpress or
plug itin untilit iscompletelyassembledand installed
accordingtothe instructions,and untilyou have read
and understoodthis instrucbonmanual:
15.WHEN usinga drillpressvise, always fastentothe
table.
16.MAKE SURE allclamps and locksare firmly
tightenedbeforedrilling.
1. YOUR DRILL PRESS MUST BE BOLTED securely
to a workbench. In addition,ifthere is anytendency
for yourdrillpressto move duringcertainoperations,
boltthe workbenchtothe floor.
2. THIS DRILL PRESS isintendedfor usa indry
conditions,indooruseonly.
3. WEAR EYE PROTECTION. USE face or dustmask
alongwithsafety gogglesifdrillingoperation isdusty.
USE ear protectors,especially duringextended
periodsofoperation.
4. DO NOT wear gloves, neckties,or looseclothing
5. DO NOT tryto drillmaterial too smallto be securely
held.
6. ALWAYS keephands out ofthe path of a drillbit.
Avoidawkward hand positionswhere a sudden slip
couldcause yourhandto move intothedrillbit.
7. DO NOT installor use any drill bit thatexceeds 175
mm (7") in lengthor extends 150 mm (6") below
thechuckjaws. They can suddenlybendoutwardor
break.
8. DO NOT USE wire wheels, router bits, shaper cutters,
circle(fly)cutters,or rotaryplanerson thisdrillpress.
17.SECURELY LOCK THE HEAD and table supper to
the column, and thetable to the table supportbefore
operatingthe drillpress.
18.NEVER turnyourdrillpresson beforeclearingthe
table of allobjects (tools,scrapsof wood, etc.)
19.BEFORE STARTING the operation,jog the motor
switchto make sure the drillbitdoes notwobbleor
vibrate.
20.LET THE SPINDLE REACH FULL SPEED before
startingtodrill.If yourdrillpress makes an unfamiliar
noiseor if itvibratesexcessively,stop immediately,
turnthe drillpress offand unplug.Do not restartuntil
the problemiscorrected.
21.DO NOT perform layoutassembly or set up work on
the tablewhilethe drill press isin operation.
22.USE RECOMMENDED SPEED for drill accessory
and workpiecematerial. SEE INSTRUCTIONS that
comewiththe accessory
23.WHEN DRILLING largediameter holes,clamp the
workpiece firmlytothe table. Otherwise, the bitmay
grapand spinthe workpieceat high speed. DO NOT
USE flycuttersor multiple-parf hole cutters,as they
cancome apart or become unbalancedin use.
9. WHEN cuttinga largepiece ofmaterial make sure it
isfully supportedat the table height.
24.MAKE SURE the spindle has come to a complete
stop before touching the workpiece.
10.DO NOT perform any operation freehand. ALWAYS
holdtheworkpiece firmly againstthe table so itwill
notreckor twist. Use clamps or a visefor unstable
workpiece.
11.MAKE SURE there are no nailsor foreign objectsin
the partofthe workpieceto be drilled.
12.CLAMP WORKPIECE OR BRACE against the left
side ofthe columnto prevent rotation.Ifit is too short
or thetable istilted, clamp solidlyto the table and use
the fence provided.
25.TO AVOID INJURY from accidental starting,always
turnthe switch"OFF" and unplugthe drill press
beforeinstallingor removing any accessoryor
attachmentor makingany adjustment
26.KEEP GUARDS IN PLACE and inworkingorder.
27.USE ONLY SELF-EJECTING TYPE CHUCK KEY as
providedwiththedrill press
13.IF THE WORKPIECE overhangs the table such that
it will fall or tip if not held, clamp it to the table or
provide auxiliary support.
SAVE THESEINSTRUCTIONS
Loading ...
Loading ...
Loading ...