Loading ...
Loading ...
Loading ...
36” Side-by-Side (in inches)
Dispenser Cutout
Position
ABCD E F G
1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16
.10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4
3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 17-13/16 3-1/4
42” Side-by-Side (in inches)
ABCD E F G
1/4” Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10” Spacer Panel 39 8-5/8 67 13-1/4 23-1/4
3/4” Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16 17-15/16 3-1/4
48” Side-by-Side (in inches)
ABCD E F G
1/4” Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 29-9/16
.10” Spacer Panel 45 8-5/8 67 17-1/4 25-1/4
3/4” Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16 17-15/16 5-1/4
3/4” OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel
must be secured to a 1/4” thick backer panel which
slides into the trim. A spacer panel 0.10” thick must be
placed between the overlay and backer panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws
must be countersunk into the backer panel.
NOTE: Left-to-right offset
is not always equal to top-
to-bottom offset.
9
Spacer Panel
Overlay Panel
Backer Panel
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
IMPORTANT NOTE: Maximum total weight for the
assembled panels:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• Grille Panel – 18 lbs.
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels. The overlay
dispenser trim is designed to fit a total panel thickness of 1.100”.
• If the panel is less than 1.100” a noticeable gap may be created around the dispenser trim.
• If the panel is more than 1.100” the dispenser trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 12.
• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.
• Alternative panel construction methods such as securing a 3/4” panel to a 1/4” backer panel cannot
be used. Another method, routing a 3/4” thick panel on all sides, cannot be used. These methods will not result in
the required 1.100” panel thickness.
.250” + .10” + .750” = 1.100” Total Panel Thickness
3/4"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
Design Guide - Standard Installation
Loading ...
Loading ...
Loading ...