Loading ...
Loading ...
Loading ...
EN
33
Functions and operation
www.bora.com
i
As a result of use, some of the components of the gas
cooktop can become discoloured. This discolouration is
normal and does not have a negative effect on the gas
flame or the functioning of the cooktop.
i
When using the gas burner, you may hear gas escaping
from it. The burner flame turns orange as a result of
impurities on the burner and in the ambient air (dust).
These properties are normal and can occur independently
of one another.
i
In the event of smoke or fire while operating the gas
cooktop, turn off the gas supply and switch off the
appliance at the wall socket.
i
If you smell gas or have problems with the gas
installation, switch off the gas supply. Open the window
and ensure good ventilation.
X
The use of a gas cooker generates heat, moisture and
combustion products in the room in which it is installed.
Good ventilation in this room is particularly important when
the appliance is in use: natural ventilation openings must be
kept open or a mechanical ventilation device should be used.
Intensive use of the appliance for a long time may result in
a need for additional ventilation, e.g. opening a window, or
more effective ventilation, e.g. operation of the mechanical
ventilation device at a higher power level.
Correct use of the gas hob
i
Do not use the gas cooktop without cookware for
extended periods of time (>5min) with the cooktop
extractor switched on. This results in very high
temperatures and may damage the gas cooktop and air-
channelling components of the cooktop extractor.
i
The tips of the flames should remain under the base
of the pot. Protruding flame tips emit heat into the air
unnecessarily and can damage pan handles and air-
channelling components (cooktop extractor) and increase
the risk of burns. Furthermore, the outer part of the gas
flame is much hotter than the core.
i
Protect your hands when the appliance is hot by using
oven gloves or pot holders. Only use dry gloves or pot
holders. Wet or damp fabrics conduct heat more easily
and can cause steam burns. Ensure that these fabrics do
not get too close to the flames. Do not use oversized pot
holders, tea towels or similar.
i
Grease splashes and other flammable (food) residues
on the cooktop can catch fire. Remove them as soon as
possible.
X
Do not put cookware with an uneven base on the pan support.
X
Never heat empty cookware.
X
Always place the cookware on the pan support provided.
Cookware must not be placed directly on the burner.
X
Do not use roasters, pans or stone grills that are so large that
they cover several burners. The resulting heat accumulation
can damage the cooktop.
The cooktop was switched on
O
H
is shown in the control knob display for previously active
and still hot cooking zones (residual heat indicator).
O
If there is no longer any residual heat, the display will switch
off after 10 seconds.
7.3 Operating the cooktops
i
The full range of functions is only available for BORA
Professional 3.0 system cooktops in combination with
the corresponding cooktop extractors PKA3/PKA3AB and
PKAS3/PKAS3AB.
i
Clean the cooking zones before using the cooktop for the
first time (see the Cleaning chapter).
7.3.1 General operating instructions for cooktops
Cooktops are operated with 2 control knobs.
There are 9 power levels, an optional power setting and various
functions available for each cooking zone.
Each cooking zone has its own control knob. The front cooking
zone is controlled using the left-hand knob and the rear cooking
zone with the right-hand knob.
1 2
Fig. 7.6 Cooking zone indicator
[1] active front cooking zone
[2] active rear cooking zone
7.3.2 Special operating instructions for gas
cooktop PKG3
i
When operating the cooktop for the first time or after
a prolonged period without use or when the liquid gas
bottles have been changed, it is possible that the burner
may not ignite. This may be due to air in the gas pipe
or the electronic gas regulator may need recalibrating.
Follow the initial operation instructions (see the “Initial
operation” chapter).
i
Due to the use of enamelled cast iron parts, slight colour
variations and irregularities are common. Furthermore,
flash rust may appear at the support points, which can
be easily removed with a damp cloth. These spots are
normal and are not considered an impairment.
Loading ...
Loading ...
Loading ...