Loading ...
Loading ...
Loading ...
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.
37
Replace the burner cap. Check the burner ignition.
Replace the pan supports.
2.5 To Change a Hotplate Burner Thermocouple
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one
side. Ensure that the thermocouple is cool. Turn the
thermocouple so that the earth lead (no sleeve) is in line
with the slot. Lift the thermocouple clear of the hole.
Reassemble in reverse order.
2.6 To Remove or Change a Hotplate Burner
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate top (see 2.1). Remove the control
panel (see 1.2).
The burners except the right hand wok burner
are mounted on support struts. For these burners,
disconnect the burner feed pipes at the burner. Remove
the screws at the front and rear holding the support
struts. Lift the strut and burners clear. The burners are
xed to the support struts with 2 screws. Remove the
appropriate burner and t the new one. Reassemble in
reverse order. Check burner operation is satisfactory.
Right hand Wok burner
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check burner
operation is satisfactory.
3 Control
3.1 To Change the Ignition Generator
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Change the hotplate tap as detailed in 2.2
3.2 To Replace the Light Switch
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.2).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the
switch body behind the control panel and twisting
sharply. Remove the switch bezel by folding back its
locking wings and pushing forward.
Fit the new bezel to the control panel by rst lining up
the raised key on its body with the cut-out in the control
panel and pushing it in from the front.
Assemble the new switch to the bezel by lining up the
key sections and pushing home. Fit the new button by
pushing in from the front.
Replace the control panel in reverse order and test for
correct operation.
3.3 To Remove the Electronic Timer
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Pull o the timer control button(s) and remove the
control panel (see 1.2).
Remove the timer/mounting bracket assembly from the
control panel by removing the xing screws.
Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the
same time pulling the unit forward.
Reassemble in reverse order. When replacing the leads,
refer to the wiring diagram in this manual. Check the
operation of the timer.
4 Grill
4.1 To Replace the Grill or Ceramic Hob Controller
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.2) and hotplate top
(see 2.1). Disconnect the wiring from the controller.
Remove the 2 screws holding the controller to the
mounting panel.
Fit the new controller and reassemble in reverse order.
Check for correct operation.
4.2 To Remove the Grill Element
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove grill pan from inside the grill compartment;
remove the enamelled front shield from the grill roof, by
removing the 2 screws and washers.
Remove the 2 screws and washers securing the grill
element front support. Remove the screws from the grill
element.
Lift the element out carefully, disconnecting the leads
from the element terminals (noting their position).
If it is not possible to disconnect the leads in this way,
pull the cooker forward to gain access to the rear,
remove the screws securing the electric cover to the
back sheet, remove the cover and disconnect the
terminals from the rear.
Fit the new element and reassemble in reverse order.
Check the operation of the grill.
Loading ...
Loading ...
Loading ...