Loading ...
Loading ...
Loading ...
en Cleaning function
32
End
As soon as the cleaning aid has run through, a signal
sounds and the appliance ends the operation
automatically.
As soon as you open the appliance door, the interior
lighting is switched on so that you can rinse the cooking
compartment more easily. The remaining water in the
cooking compartment must be removed promptly. Do
not leave the remaining water in the cooking
compartment for a long time (e.g. overnight). The
appliance must not be operated when the cooking
compartment is still wet or damp.
Subsequent cleaning
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking
compartment with a dish cloth or a soft brush.
Stubborn residues can be removed using a stainless
steel scouring pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. Use the # touch button to switch off the appliance.
5. Leave the appliance door ajar in the stop position
(approx. 30°) for approx. one hour to allow the
enamel surfaces in the cooking compartment to dry
thoroughly. Alternatively, you can also run the rapid
drying function for the cooking compartment.
Running the rapid drying function for the cooking
compartment
1. After the cleaning aid has been run through, leave
the appliance door ajar in the stop position (approx.
30°).
2. Touch the # touch button.
3. Start CircoTherm hot air at 50 °C.
4. After five minutes, switch off the appliance and close
the appliance door.
Removing heavy deposits of dirt
You have several options for removing particularly
stubborn deposits of dirt.
■ Leave the soapy water to work for some time before
starting the cleaning aid.
■ Rub soapy water onto the dirt on the smooth
surfaces before starting the cleaning aid.
■ Repeat the cleaning aid after the cooking
compartment has cooled down.
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
Descaling comprises a number of different steps. For
hygiene reasons, the descaling programme must be
run through completely before the appliance is ready
for operation again. In total, the descaling programme
runs for approx. 70–95 minutes.
■ Descale (approx. 55–70 minutes), then empty and
refill the water tank
■ First rinsing cycle (approx. 9–12 minutes), then
empty and refill the water tank
■ Second rinsing cycle (approx. 9–12 minutes), then
empty and dry the water tank
If descaling is interrupted (e.g. due to a power failure or
because the appliance is switched off), you will be
prompted to rinse the appliance twice when you switch
it back on. The appliance cannot be used until the
second rinsing cycle has finished.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only another five or fewer steam-assisted
operations are possible, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
■ Risk of damage to the appliance: Only use the liquid
descaler recommended by us for the descaling
programme. The length of time for which the
descaler is left to work is based on this product.
Using other descalers may damage the appliance.
Descaler order no. 311 680
■ Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This may damage the surfaces. If this does happen,
remove the descaling solution immediately with
water.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1. Mix 400 ml water with 200 ml liquid descaler to
make a descaling solution.
2. Touch the # touch button.
3. Remove the water tank and pour the descaling
solution into it.
4. Once the descaling solution has been poured into
the water tank, push the tank back in again fully.
5. Close the control panel.
6. Touch the 0 touch button.
7. Use the ( or ) button to select "Descale ,".
8. Use the & button to navigate to the next line.
The duration of the descaling process is displayed. It
cannot be changed.
Loading ...
Loading ...
Loading ...