Loading ...
Loading ...
Loading ...
28 29
CARE & CLEANING
CLEANING THE FILTER BASKETS
AND PORTAFILTER
• The filter baskets and portafilter should
be rinsed under hot water directly after
use to remove all residual coffee oils.
• If the holes in the filter baskets become
blocked, dissolve a cleaning tablet in
hot water and soak filter basket and
portafilter in solution for approx. 20
minutes. Rinse thoroughly.
CLEANING THE SHOWER SCREEN
• The group head interior and shower
screen should be wiped with a damp cloth
to remove any ground coffee particles.
• Periodically purge the machine with
hot water to rinse out any residual
coffee. Place an empty filter basket into
the portafilter. To by-pass low pressure
pre-infusion and deliver water to the
group head at full pump pressure, press
and hold the 2 CUP button. Release
button after 20 seconds.
CLEAR WATER BACKFLUSH
After each coffee making session we
recommend doing a clear water backflush
before you turn off the machine. Insert the
cleaning disc into the filter basket then
insert the portafilter into the group head.
Press the 2 CUP button and allow pressure
to build for 20secs, then press to stop &
release pressure. Repeat this 5 times to
purge any fine coffee grounds and residual
coffee oils from the brew water paths.
CLEANING THE DRIP TRAY
& STORAGE TRAY
• The drip tray should be removed,
emptied and cleaned after each use or
when the drip tray indicator is showing
Empty Me! Remove grill from the drip
tray. Wash both in warm soapy water.
The Empty Me! indicator can also be
removed from the drip tray.
• The storage tray can be removed and
cleaned with a soft, damp cloth (do not use
abrasive cleansers, pads or cloths
which can scratch the surface).
CLEANING THE OUTER HOUSING
& CUP WARMING TRAY
The outer housing and cup warming tray can
be cleaned with a soft, damp cloth. Polish with
a soft, dry cloth. Do not use abrasive cleansers,
pads or cloths which can scratch the surface.
NOTE
Do not clean any of the parts or
accessories in the dishwasher.
DESCALE (dESC)
Use this function to access descale procedures
when a descale alert is displayed on the LCD.
Please ensure you allow approximately 1.5 hour
to complete the entire descale process and
follow the step by step instructions.
If you’ve just finished using your machine,
please ensure to turn the machine off and
allow to cool for at least 1 hour before
starting your descale process.
1 – Prepare for Descale
a) Empty the drip tray and insert into
position.
b) Turn the machine off and allow to cool
for at least 1 hour. With the machine
off, press and hold the 1 CUP button,
then press and hold the POWER button
together for 3 seconds. rEST will apear
on the LCD.
CARE & CLEANING
c) Press UP or DOWN arrow to set mode, the
‘dESC’ will appear on the LCD. Press the
MENU button to enter Descale mode.
2 – Empty Boilers
a) Remove the grey silicone cover on the
lower front panel marked DESCALE
ACCESS. Place a cloth over the drip tray
to stop steam escaping.
REMOVE
b) Use a flat-head screwdriver to rotate the
right screw counter-clockwise until the
valve is fully open. As the valve opens,
steam may be released.
NOTE
If there’s no water released into the
drip tray, press and hold the 1 CUP
button for 3 seconds. This will release
water from the boiler
When the water is completely empty, close
the valve by rotating screws clock-wise until
sealed. Do not overtighten screws to avoid
damages to the valves.
c) Next, repeat the above process on the
left screw.
d) Empty the drip tray. Use caution as the
drip tray may be hot.
e) Empty water tank, remove water filter.
f) Place descale solution into water tank,
fill with cold water to MAX line,
(if an alternative cleaning solution is
used, please follow the manufacturer’s
instructions accordingly). Lock water
tank back into position at the back of
the machine.
NOTE
If water tank has not been removed,
replaced or is empty, “FILL TANK”
will appear on the LCD.
Loading ...
Loading ...
Loading ...