Loading ...
Loading ...
Loading ...
Remove the Doors
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1.
2.
Unplug refrigerator or disconnect power.
Open both doors to 90 ° . Remove the base grille by removing the two
screws, then pulling out on the outside corners. ,See Graphic 7.
NOTE: The doors must only be opened to 90 °. If they are opened all
the way, the base grille will not come off.
3. Disconnect the water tubing, located behind the base grille on the
freezer door side. The dispenser tubing runs through the door hinge,
and must be disconnected in order to remove the door.
[] Style h Press the colored outer ring against the face of fitting and
pull the water tubing free. ,See Graphic 2,4.
NOTE: Keep the water tubing connector attached to the tube
that runs underneath the freezer. The door cannot be removed if
the connector is still attached to the tube that runs through the
door hinge.
[] Style 2: Firmly pull on the clasp to release the tube, then pull the
water tubing free. See Graphic 2B.
NOTE: Keep the clasp attached to the tube that runs underneath
the freezer.
4. Disconnect the wJring_ located behind the base grille on the freezer
door side. See Graphic 8.
[] Remove the P-clamp using a 1/4" hex head socket wrench. Remove
the small wiring bundle from the P clamp.
[] Remove the wiring clip using a 1/4" hex-head socket wrench.
[] Pull the electrical housing out from under the refrigerator.
Disconnect the wiring plugs from the housing.
[] Gently pull the large wiring bundle (with two white plugs) through
the routing plate.
5. Close both doors and keep them closed until you are ready to lift them
free from the cabinet.
6. Use a 3/16" hex key to remove the top left hinge screws as shown. See
Graphic 4.
mMPORTANT: Do not remove either screws in A.
Excessive Weight Hazard
Use two or more people to lift the freezer door.
Failure to do so can result in back or other injury.
7. Lift freezer door straight up off bottom hinge. ,See Graphic 5. The
water tubing and wiring remain attached to the freezer door and pull
through the bottom left hinge.
NOTE: This may require two people - one to lift the door and another
to feed the water tubing and wiring through the hinge. Be sure the hole
in the hinge is clear of obstructions, then gently pull one water tube
through the hinge. (Avoid kinking the tube.) Next, gently pull the other
water tube through the hinge, again avoiding kinks. Finally, gently pull
the wiring bundle (including the grommet and wiring plugs) through
the hinge.
8_
IMPORTANT: Rest the door on its side on a soft, clean surface, such as
a towel, blanket or piece of cardboard. This will help avoid damaging
the door, water tubing and wiring.
Use a 3A6" hex key to remove the top right hinge screws as shown. ,See
Graphic 6.
IMPORTANT: Do not remove either screw A.
9.
Lift the refrigerator door straight up off bottom hinge.
IMPORTANT: Rest the door on its side on a soft, clean surface, such as
a towel, blanket or piece of cardboard. This will help avoid damaging
the door.
10. It may not be necessary to remove the bottom hinges to move the
refrigerator through a doorway. Both bottom hinges have similar
construction.
[] If necessary, use an internal star drive or a 3/8" hex head socket
wrench to remove the bottom hinges. See Graphic 7.
iMPORTANT: The leveler brackets are mounted behind the
hinges, if you remove the hinges, make sure that the leveler
brackets are replaced when reinstalling the hinges.
Replace the Doors and Hinges
Replace both bottom hinges, if removed. Make sure that the leveler
brackets are assembled behind the hinges. Tighten screws.
IMPORTANT: When the screws are tightened properly, there should not
be any gaps between the refrigerator, leveler bracket and hinge.
NOTE: There are two wiring bundles that run underneath the freezer - a
large bundle with a large grommet and two white plugs at the end, and a
small bundle with a small grommet and one yellow plug at the end.
Excessive Weight Hazard
Use two or more people to lift the freezer door.
Failure to do so can result in back or other injury.
2_
Before replacing the freezer door on the bottom left hinge, feed the
small wiring bundle through the hinge. Assistance may be needed.
IMPORTANT: Do not feed the large wiring bundle through the hinge.
This bundle is intended to run directly from the door to the connections
beneath the freezer. Forcing the large bundle through the hinge may
damage the door and/or the wiring_ and will keep the door from
closing properly.
3. Feed both water tubes through the bottom left hinge, then replace the
freezer door on the hinge. Assistance may be needed.
NOTE: Provide additional support for the doors while the top hinges are
being replaced. Do not depend on the door magnets to hold the doors in
place while you are working.
4. Align and replace the top left hinge as shown. ,See Graphic 4z.Tighten
screws.
Loading ...
Loading ...
Loading ...