Loading ...
Loading ...
Loading ...
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the plastic part that is attached to the inlet of the
water valve,
3. Attach the copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not overtighten.
4. Use the tube clamp on the back of the refrigerator to secure the tubing
to the refrigerator as shown. This will help avoid damage to the tubing
when the refrigerator is pushed back against the wall.
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any connections (including connections at the
valve) or nuts that leak.
A. Tube clamp D. Compression nut
B. Tube clamp screw E. Valve inlet
G Copper tubing
7.
On some models, the ice maker is equipped with a built-in water
strainer. If your water conditions require a second water strainer, install
it in the 1/4" (6.35 ram) water line at either tube connection. Obtain a
water strainer from your nearest appliance dealer.
Style 3
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water tube on
the rear of the refrigerator.
3. If the gray water tube supplied with the refrigerator is not long
enough, a 1/4" x 1/4" (6.35 mmx 6.35 mm) coupling is needed in order
to connect the water tubing to an existing household water line.
Thread the provided nut onto the coupling on the end of the copper
tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench two
more turns. Do not overtighten.
Complete the Installation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
OO not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See "Prepare the Water System" or "Water
and Ice Dispensers."
NOTE: Allow 24 hours to produce the first batch of ice. Allow 72 hours to
completely fill ice container.
Please read before using the water system.
Immediately after installation, follow the steps below to make sure that the
water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. The On/Off switch
can only be accessed when the ice storage bin has been removed. The
switch is located on the freezer door, on the left side of the wall that
surrounds the ice storage bin. Move the switch to the OFF (right)
setting.
2. Make sure the water filter is properly installed.
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
A B C D E F G
A. Refrigerator water tubing E. Ferru/e (purchased)
B. Nut (provided) E Nut (purchased)
C. Bulb G. Household water line
D. Coup/ing (purchased)
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including connections
at the valve) that leak.
3. Flush the water system. Use a sturdy container to depress and hold the
water dispenser lever for 5 seconds, then release it for 5 seconds.
Repeat until water begins to flow. Once water begins to flow, continue
depressing and releasing the dispenser lever (5 seconds on, 5 seconds
off) until a total of 3 gal. (12 L) has been dispensed. This will flush air
from the filter and water dispensing system, and prepare the water
filter for use. Additional flushing may be required in some households.
As air is cleared from the system, water may spurt out of the dispenser.
4. Open the freezer door and turn on the ice maker. Move the switch to
the ON (left) position. Please refer to the "Ice Maker and Storage Bin"
section for further instructions on the operation of your ice maker.
• Allow 24 hours to produce the first batch of ice.
• Discard the first three batches of ice produced.
• Depending on your model, you may want to select the maximum
ice feature to increase the production of ice.
12
Loading ...
Loading ...
Loading ...