Loading ...
Loading ...
Loading ...
en Basic settings
22
--------
To access the basic settings:
The hob must be off.
1. Switch on the hob.
2. Within ten seconds, touch and hold the 0 symbol
for approximately four seconds.
The first four displays provide product information.
Touch the settings area to view the individual
displays.
3. Touching the 0 symbol again takes you to the basic
settings.
™ and ‚ flash alternately on the displays and ‹
appears as a presetting.
4. Touch the 0 symbol repeatedly until the required
function is displayed.
5. Then select the required setting from the settings
area.
6. Touch the 0 symbol for at least four seconds.
The settings have been saved.
Leaving the basic settings
Turn off the hob with the main switch.
™‚ˆ
Setting air recirculation mode or air extraction mode
‹ Configuring air recirculation mode.*
‚ Configuring air extraction mode.
™‚‰
Setting the automatic start
‹ Switched off.
‚ Switched on: The ventilation system starts at a power level in accordance with the relevant power levels for the cooking
zones.*
™ƒ‹
Setting the run-on
‹ Switched off.
‚ Switched on*:
If the hob is working in air extraction mode, the ventilation system switches itself on for approx. six minutes at power level „.
If the hob is working in circulating-air mode, the ventilation system switches itself on for approx. 30 minutes at power level ‚.
The run-on function automatically switches off after this time.
™‹
Restore to standard settings
‹ Individual settings.*
‚ Restore factory settings.
*Factory setting
**The hob's maximum power output is shown on the rating plate.
Product information Display screen
After-sales service index (ASSI)
‹‚
Production number
”š
Production number 1
Š†.
Production number 2
‹.†
Energy consumption indicator en
23
[Energy consumption
indicator
Ener gy cons umpt i on i ndi c at or
This function indicates the total amount of energy
consumed by this hob the last time it was used for
cooking.
Once the hob is switched off, the energy consumption
is displayed in kilowatt hours (e.g.
‚.‹‰ kWh) for 10
seconds.
The accuracy of the information displayed depends on
the voltage quality of the mains power supply, among
other factors.
You can find out how to switch this function on in the
section on ~ "Basic settings"
tCookware check
Cook war e check
This function can be used to check the speed and
quality of the cooking process depending on the
cookware.
The result is a reference value and depends on the
properties of the cookware and the hotplate being used.
1. Correctly position the pot with approximately 200 ml
of water, at room temperature, on the most suitable
cooking zone for the diameter of the bottom of the
pot.
2. Go to the basic settings and select the setting ™‚ ƒ.
3. Press the programming area. A flashes in the
cooking zone displays.
The function has now been activated.
After 10 seconds, the cooking result and the speed of
the cooking process appear in the visual displays for
the cooking zone.
Check the result using the following table:
To reactivate this function, touch the settings range.
Notes
■ If the diameter of the hotplate used is much smaller
than the diameter of the cookware, only the middle
of the cookware can be expected to heat up. This
may result in the cooking results not being as good
as expected or being less than satisfactory.
■ You can find information on this function in the
section on ~ "Basic settings".
■ You can find information on the type, size and
positioning of the cookware in the section on
~ "Induction cooking".
Result
‹
The cookware is not suitable for the hotplate and will therefore
not heat up.*
‚
The cookware is taking longer to heat up than expected and the
cooking process is not going as well as it should.*
ƒ
The cookware is heating up correctly and the cooking process
is going well.
* If there is a smaller hotplate available, test the cookware again on the
smaller hotplate.
Loading ...
Loading ...
Loading ...