Loading ...
Loading ...
Loading ...
safetyinstructions for scroll saw
When c[itt _g:irreg;u|adY-shaped workpieces plan your Before starting Your cut watch the saw while it runs. If it
work sO it Will dot pii_ch the blade. A piece:of, molding, makes an unfamiliar noise or vibrates a lot, stop immedi-
-f0i; examp'le must lay flat orbe held bya f_ture Or jig ately Turn the saw off. Unplug the saw. Do not restart
that Willnot let:ittW st, rock oi slip whilebeihg cut, until lindingand correcting the problem.
, P_e_:sUpport round:materiai such as dowel rods, or KEEP CHILDREN AWAY. Keep al_ visitors a safe dis-
tul_ing__ey_have _ tendency to roll during a cut, _using tance from: the :saw. Make sure bystanders are clear o!
the bl_e to bite. To avoid this, always use a "V" block. : the Saw and workpiece.
-Cut onlyone workpiece at a time.
, Clear, everything except the workpiece and related
- Support devices off the table before turning the saw on.
Plan the way you will hold the workpiece from start
to finish.
Do not hand hold pieces so small that your fingers will go
under the work hold down. Use jigs or fixtures to hold the
work and keep your hands away from the blade.
Avoid awkward operations and hand positions where a sud-
den slip could cause fingers or hand to move intothe blade.
Don't Overreach. Keep good footing and balance.
Keep your face and body to one side oI sawb{ade, out of
line-with a possible thrown piece:
SECURE WORK. Use clamps to hold work when practi-
cal. It!s often safer than using your hand, and frees both
hands to operate the too!.
Avoid awkward operations and hand positions where a sud-
den slip could cause fingers or hand to move into the blade.
DON'T OVERREACH. Keep good footing and balance.
Keep your face and body to one side of the blade, out of
line with a possible thrown piece if the blade should break.
WHENEVER SAW IS RUNNING
DON'T FORCE TOOL. It wil!do the job better and safer at its
designed rate. Feed the workpiece into the saw blade only
fast enough to let it cutwithout bogging down or binding.
Before freeing any jammed material:
* Push switch "OFF".
......... all moving parts to stop.
o Unplug the saw.
When backing up the workpiece, the blade may bind
in the kerr (cut). This is usually caused by sawdust
clogging up the kerr. If this happens:
- Turn switch "OFF".
, Wait for allmoving parts to stop.
° Unplug the saw
oRemove the blade from the blade holders.
- Remove workpiece with blade from the table, Remove
blade from workpiece.
Before removing loose pieces from the table, turn
saw off and wait for all moving parts to stop.
BEFORE LEAVING THE SAW
Wait for all moving parts to stop.
MAKE WORKSHOP CHILD PROOF. Unplug the saw.
Lock the shop or on/off knob. Store the key away from
children and others not qualified to use lhe tool.
cause a severe injury,
• i! rl
electrical connections
DANGER: To avoid electrocution:
1. Use only identical replacement parts when seP
vicing. Servicing should be performed by a
qualified service technician.
2. Do not use in rain or where floor is wet.
This tool is intended for indoor residential use
only.
t WARNING Do not permit fingers to touch the ter- I
I minals of plug when installing or removing the
I
I plug toot from the outlet, i
I If power cord is worn or cut, or damaged in any
I way, have it replaced immediately.
NOTE: The plug supplied on your too! may not fit intothe
outlet you are planning to use. Your local electrical Code
may require slightly different power cord plug.connec-
tions. It these differences exist refer to and make the
-proper adjustments per your local code before your tool
is pluggea in and turned on.
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electnc current to
reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment grounding con-
ductor and a grounding plug, as shown. The plug must
be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
Do not modify the plug provided. If it wil not tit lhe outlet.
have the proper outlet installed by a qualified electrician.
A temporary adapter may be used to connect this plug to
a 2-pole outlet as shown, if a properly grounded outlet is
not available. This temporary adapter should be used
only until a properly grounded outlet can be installed by a
qualified electrician. The green colored rigid ear. tug and
the like, extension from the adapter must be connected to
a permanent ground such as a properly grounded outlet
box.
Loading ...
Loading ...
Loading ...