Loading ...
Loading ...
Loading ...
5
bromic.com/heat
the place of purchase.
• In case of direct connection to a supply line, a bipolar
circuit breaker with contact opening distance of at
least 3 mm must be fitted upstream from the supply
line. Contact an authorised service technician if you
are unsure if you have a circuit breaker installed on the
premises.
• Do not install the heater directly near a bathtub, shower,
swimming pool or other body of water. Any switches
or controls must not be within reach of a person in the
bathtub, shower, swimming pool or other body of water.
• To maintain Ingress Protection Rating (IP54), only
suitable IP54 (or better) rated outdoor plug & sockets
should be used for electrical installation.
• This product does not have a switch for electrical
disconnection. A means for disconnection of the heater
must be incorporated in the wall socket & fixed wiring
according to the local electrical codes.
• Do not roll heater over the supply cable when moving
heater, to prevent damage to cable.
• If the supply cable is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a safety hazard.
• This heater is not equipped with a device to control
the room temperature. Do not use this heater in small
rooms when they are occupied by persons not capable
of leaving the room on their own, unless constant
supervision is provided.
• Do not excessively bend the electrical connection to the
power supply.
• Keep the supply cable & plug away from sharp edges
during handling and installation.
• Do not pull on the supply cable or subject it to traction
force.
•
Caution should be taken when dismantling goods from
shipping container to prevent from injury when lifting heavy
parts. Maximum safe lifting 16kg per person.
•
Caution should be taken when lifting weights. Each weight is
10 kg. Maximum safe lifting 16kg per person.
•
All 10 weights must be assembled to base during assembly,
to prevent tipping and any unintended movement of heater.
•
Caution should be taken when moving the base. Use two
people to guide heater when moving position to prevent
collisions with surrounding objects. Weights must be
assembled to heater when moving full assembled heater,
to prevent tipping. Heater can be moved forwards and
backwards, and pivoted on the two assembled wheels.
•
When moving base, ensure floor is adequately protected.
•
Heater must be installed on flat surface capable of
withstanding at least 160kg. Heater must not be installed
on soft surfaces which cannot support the weight of heater
(e.g. grass, mud, dirt).
•
Do not lean on heater or rest any objects leaning up against
heater, including the arm.
•
Do not hang any foreign items o any part of this appliance
e.g. do not hang towels, clothing, lines, lights, cables.
•
Do not swing from arm or heater head.
•
Do not stand or sit on any part of heater, including the base.
•
When not in use, disconnect, cover & store product away
from sun & rain exposure.
•
The Heater is designed to withstands winds of up to
30km/h. When located in areas prone to high wind
conditions greater than 30km/h, the Base must be fixed
to ground or stored away protected from wind. Fixings
must be removed prior to moving heater. Weights must be
assembled to heater when moving full assembled heater, to
prevent tipping.
•
Base Cover & Mounting screw must be fitted to ensure
protection of base components.
•
Rubber seal must be fitted to Base Cover to protect painted
pole surfaces from scratching.
•
O-rings must be fitted to arms to prevent water ingress and
reduce corrosion.
•
Caution: Base can be a trip hazard.
•
Do not use heater if Heater Head is not level with the
ground. Angle must be checked during assembly using spirit
level (not included).
•
Do not use heater if heater head or arm is loose.
• Check product label for correct voltage and wattage to
ensure power source conforms to the heater’s requirements.
• The exterior housing of the heater should be cleaned
regularly. To clean the appliance; ensure heater is o and has
been o for at least 2 hours after operation, before wiping
o any dirt/dust with a soft damp cloth & glass cleaner. Salt
in the air can cause rusting of metal, especially at locations
near the coast. Additional cleaning of the heater with a soft
damp cloth fortnightly will aid in maintaining the product’s
appearance.
• Do not clean heater with cleaners that are combustible or
corrosive.
IMPORTANT NOTES AND WARNINGS CONTINUED ...
SAVE THESE INSTRUCTIONS
Loading ...
Loading ...
Loading ...