Loading ...
Loading ...
Before Each Use: i
Inspect your sander. Check for:
oalignment of moving parts,
_obinding of moving parts,
• broken or damaged parts,
• fixtures that cause a gap larger than 1/16" between
work support and sanding surface,
° sanding belt narrower than 4 inches. Narrower belts
uncover parts that could trap your fingers.
° worn or damaged electric cords,
•stable mounting
• any other condition that may affect the way the sander
works.
If any part is missing, bent, or broken in any way, or any
electrical parts don't work properly, turn the sander off
and unplug the sander. Replace damaged, missing, or
failed parts before using the sander again.
Disconnect the sander to avoid injury from accidental
starting. Pdrn the switch off, unplug the sander and
remove the switch key before changing the setup, sand-
ingdisc or belt or adjusting anything.
Maintain tools with care. Keep the sander clean for best
and safest performance, Follow instructions for lubricat-
ing.
Remove wrenches from tool before turning on.
To avoid injury from jams, slips or thrown pieces:
°Use only recommended accessories. Consult this
owner's manual for recommended accessories. The
use of improper accessories may cause injury, See
"Accessory" section..
°Adjust any work support to clear the sanding surface
by no more than 1/16 of an inch. When checking clear-
ance between the belt and work support, press the belt
flat against the metal beneath it.
• Make sure all clamps and locks are tight and no
parts have excessive play.
• Keep work area clean. Cluttered areas and benches
invite accidents. Floor must not be slippery.
Plan Ahead To Protect Your Eyes, Hands,
Face and Ears:
Know your sander. Read and understand the owner's
manual and labels affixed to the tool. Learn its application
and limitations as well as the specific potential hazards
peculiar to this tool.
To avoid injury from accidental contact with moving
parts:
°Keep guards in place and in working order.
•Don't do layout, assembly, or setup work on the sander
while any parts are moving.
Avoid accidental starting. Make sure switch is "OFF"
before plugging sander into a power outlet.
Dress for Safety:
°Wear nonslip footwear.
o
°
o
°
you
Tie back long hair.
Roll tong sleeves above the elbow.
Noise levels vary widely. To avoid possible hearing
damage, wear ear plugs or muffs when using sander
for hours at a time.
Sanding operations are usually dusty. Wear a dust
mask along with the safety goggles.
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wrist watches). They can get caught and draw
into moving pads.
WEAR YOUR
•Wear safety goggles. Any power sander can throw
foreign objects into the eyes_ This can cause perma-
nent eye damage. Wear safety goggles (not glasses)
that comply with ANSI Z87.1 (shown on package).
Everyday eyeglasses have only impact resistant
lenses. They are not safety glasses. Safety goggles
are available at area stores. Glasses or goggles not in
compliance with ANSI Z87.1 could seriously hurt you
when they break.
Plan your work. Think through how you will hold and
maneuver the workpiece from start to finish.
Use the right tool. Don't force toot or attachment to do a
ob it was not designed to do.
CAUTION: This machine is not designed for heavy!
deburring operations. When finishing metals,
sparks or hot fragments could cause a fire. To
avoid this:
•Disconnect any dust collecting hose from the
sander.
•Remove all traces of wood dust from inside the
sander, i
I
•Remove all traces of metal dust from inside the
sander before sanding wood again, i
Inspect your workpiece. Make sure there are no nails
or foreign objects in the part of the workpiece to be
sanded.
Plan the way you will hold the workpiece from start to
finish. Avoid awkward operations and hand positions
where a sudden slip could cause finger or hand to move
into a sanding surface. Keep fingers away from where the
belt goes intothe dust trap.
Don't overreach. Keep good footing and balance.
Keep your face and body to one side. Stay out of tine
with a possible throwback.
Loading ...
Loading ...
Loading ...