Loading ...
Loading ...
Loading ...
18
DESCRIPTION OF THE CST REMOTE CONTROL
D1
D10
D5
D3D2D9
D8
D4D6 D7
D1 ON/STAND-BY (on/o) button
D2 SILENT button
D3 Air ow button
D4 Decrease button
D5 Countdown Timer
D6 MODE button
D7 Increase button
D8 myEcoReal Feel button
D9 Swing button (ap swing)
D10 Indication LED
USING THE CST REMOTE CONTROL
The CST remote control is an innovative technology that allows
a better wellbeings regulation, thanks to the sensors provided.
In order to optimize the wellbeings conditions around you, we
suggest you to keep it near you.
• The remote control must be no more than about 10 meters
away from the appliance (g. 10) (even in non line of sight).
The maximum range may be lower depending on the envi-
ronment. It belongs to Bluetooth class 2 device class.
• The CST remote control must be handled with care. Do not
drop it or expose it to direct sunlight or sources of heat. It
is advisable to keep the CST remote Control Unit lied over a
table or a plan surface.
Do not hold the CST remote Control in your hand for long
time to avoid altering the reading of the sensors.
The CST sensors are also disabled if the CST remote control
is positioned at a distance less than 1 m from the unit.
• The CST remote control is equipped with touch sensitive
buttons.
•
The CST remote control is equipped with a double color built-
in LED (D10) (white/red). White indications are used for:
- signaling the touching of each button with 3 fast
ashes
- every 30 seconds it blinks for data transmission
- signaling the entering of pairing phase with periodic
blinking
- signaling the batteries good status
• The same indications but in red color mean that the batter-
ies begin to be exhausted.
Please note: The remote control can be safely stored in the ap-
propriate compartment (A11).
TURNING THE APPLIANCE ON/OFF
• Plug into the outlet.
• Touch the
C1C2
C4
C11
C13
C12
C9
C7
C5
C6
C3
C16
C14
C10
C15
C17
C8
ON/STAND-BY button (D1). When turned on,
the air conditioner starts operating in the same mode as
when it was turned o.
• Touch the
C1C2
C4
C11
C13
C12
C9
C7
C5
C6
C3
C16
C14
C10
C15
C17
C8
ON/STAND-BY button (D1) again to switch the
appliance o.
Please note: Never switch the appliance o by removing the
plug. Always switch it o by touching the
C1C2
C4
C11
C13
C12
C9
C7
C5
C6
C3
C16
C14
C10
C15
C17
C8
ON/STAND-BY but-
ton (D1) and waiting few minutes before removing the plug.
Only in this way the appliance will perform the standard check-
ings.
SELECTING THE OPERATING MODES
The operating modes available on the CST remote control
through the MODE button (D6) correspond to those on the ap-
pliance control panel (C).
SELECTING THE TEMPERATURES
In conditioning mode touch button (D4) or (D7) to select
the desired temperature.
SELECTING THE AIR FLOW
In conditioning and fan modes, touch button (D3) to select
the desired air ow.
The air ows available are:
Minimum air ow: when most silent operation is
desired.
Medium air ow: when the noise level needs to
be low but with a good comfort level.
Maximum air ow: for maximum performance.
Auto air ow: the appliance automatically
chooses the air ow based on the temperature
selected and the environmental conditions. This
selection is only available in conditioning mode.
myEcoReal Feel FUNCTION
myEcoReal Feel is the innovative De’Longhi technology that
works simultaneously on temperature reduction and humidity
control, securing best comfort level. With traditional systems,
during working time, optimal comfort conditions may be
Loading ...
Loading ...
Loading ...