Loading ...
Loading ...
ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SA lr3!
WARNING: FOR YOUR OWN SAFETY, DO NOT B. Wear safety goggles that comply with ANSI
OPERATE YOUR SAW UNTIL IT IS COMPLETELY Z87.1, and a face shield or dust mask if
ASSEMBLED AND INSTALLED ACCORDING TO
THE INSTRUCTIONS... AND UNTIL YOU HAVE
READ AND UNDERSTAND THE FOLLOWING:
1. GENERAL SAFETY INSTRUCTIONS FOR
POWER TOOLS... SEE PAGE 2
2. GETTING TO KNOWYOUR SAW... SEE PAGE
22
3. BASIC SAW OPERATION ..... SEE PAGE 27
4. MAINTENANCE ............. : SEE PAGE 41
5, STABILITY OF SAW
If there is any tendency for the saw to tip over or
move during certain cutting operations such as
cutting extremely large heavy panels or long
heavy boards, the saw should be bolted down.
If you attach any kind of table extensions over
24" wide to either end of the saw, make sure you
either bolt the saw to the bench or floor as
appropriate, or support the outer end of the
extension from the bench or floor, as
appropriate.
6. L_)CATION
The saw should be positioned so neither the
operator nor a casual observer isforced to stand
in line with the saw blade.
7. KICKBACKS
A "KICKBACK" occurs during a rip-type
operation when a part or all of the workpiece is
thrown back violently toward the operator.
Keep your face and body to one side of the
sawblade, out of line with a possible "Kickback."
Kickbacks -- and possible injury from them
can usually be avoided by:
A. Maintaining the rip fence parallel to the
sawblade.
B. Keeping the sawblade sharp. Replace or
sharpen antikickback pawls when points
become dull.
C. Keeping sawblade guard, spreader, and
antikickback, pawls in place and operating
properly. The spreader must be in alignment
with the sawblade and the pawls must stop a
kickback once it has started. Check their
action before ripping.
D. NOT ripping work that is twisted or warped or
does not have a straight edge to guide along
the rip fence.
E. NOT releasing work until you have pushed it
all the way past the sawblade.
F. Using a push stick for ripping widths of 2to 6
in., and an auxiliary fence and push block for
ripping widths narrower than 2 in. (See "Basic
Saw Operation Using The Rip Fence"
section.)
G. NOT confining the cut-off piece when
ripping or cross-cutting.
8. PROTECTION: EYES, HANDS, FACE, EARS,
BODY
A. If any part of your saw is missing,
malfunctioning, or has been damaged or
broken such as the motor switch,
electronic' controls, or other operating
control, a safety device or the power cord...
cease operating immediately until the
particular part is properly repaired or
replaced.
operation is dusty. Wear ear .plugs or muffs
during extended :peldods of operation
C. Small loose pieces of wood or other objects
that contact the rear of the revolving blade
can be thrown back at_"_he'0_rator at
excessive speed. This can usually be avoided
by keeping the guard and spreader in place
for all thru-sawing operations-(sawing
entirely thru the work) AND by removing all
loose pieces from the table w tb a_!ong Stick of
wood IMMEDIATELY' after they are cut off.
D. Use extra caution when the guard assembly is
removed for resawing_ da,doing, rabbeting, or
molding -- replace the guard as soon as that
operation is completed. '-'--
E. For rip or rip-type cutso the .following endof a
workpiece to which a push stick or push
board s applied mu-st, jbe ° squar_e
(perpendicular to the ferlce) in order that feted
pressure applied to ,the workp_ece.by"the
push stick or block does not cause 'the
workpiece to come away from. thefence, and
possibly cause a kickback.
F. During rip and rip type cuts, the workpi.ece
must be held down on the table andagainst
the fence with a push stick, push block, and
featherboards, as required. A featherbOard is
made of solid lumber (at least 3/4" thick) per
sketch.
I" 24" ",1
5/_" APART
G. NEVER turn the saw "ON"before c[e_rin_g the
table of all tools, wood scraps, etc_.,except,the
workpiece and related feed or Support
devices for the operation plan'*ned.
H. NEVER place your face or body in ine with
the cutting tool.
I. NEVER place your fingers or hand&,in .the
path of the sawblade or other Cqt.ting4oo:L.
J. NEVER reach in back of the cdtti.'ng"tool.with
either hand to hold dowr_i or S!Jp.portthe
workpiece, remove wood scraps,.er for,any
other reason. Avoid awkward 0perat.i0rnsand
hand positions where a Suddenslip could
cause fingers or hand to move into a
sawblade or other cutting tool.
K. DO NOT perform layout, assembly, or setup
work on the table while the cutting tool is
rotating.
L. DO NOT perform any operation
"FREEHAND" -- always use either the rip
fence or the miter gauge to pOsition and
guide the work.
M. NEVER use the rip fence when crosscutting
or the miter gauge when ripping. DO NOT use
the rip fence as a length stop.
Never hold onto or touch the "free end" of the
workpiece or a "free piece" that is cut off,
while power is "ON" and/or the sawblade _s
rotating.
3
Loading ...
Loading ...
Loading ...