Loading ...
Loading ...
Loading ...
.
SAW_()_TO_ SWITCH:
Thi,s_swit_h i_used to turn the saw motor on and
off___,,_ '_L .__
NOTE:_Pdsl_i_ingoff either the Saw Motor Switch
or the Master Switch will shut off power to the
saw motor.
NOTE: Only the _-]. and JOG keys
will
work
when the Saw Motor Switch is "ON". The
elevation only is displayed as long as this switch
is "ON".
Operation of this switch is the same as the
Master Switch except for the yellow key.
WARNING: Do not stand in line with blade when
turning switch on.
Do not cycle motor switch "ON" and "OFF"
rapidly, as this may cause the sawblade to
loosen. In the event this should occur, allow the
sawblade to come to a complete stop and
retighten the arbor nut normally, not
excessively.
Never leave the saw with power "ON".
The display
information.
WARNING: FOR YOUR OWN SAFETY, LOWER
BLADE OR OTHER CUTTING TOOL BELOW
TABLE SURFACE. (IF BLADE IS TILTED, RETURN
IT TO VERTICAL (0°) POSITION). ALWAYS LOCK
THE SWITCH "OFF". WHEN SAW IS NOT IN USE..
• REMOVE KEY AND KEEP IT IN A SAFE PLACE...
ALSO... IN THE EVENT OF A POWER FAILURE
(ALL OF YOUR LIGHTS GO OUT) TURN SWITCH
OFF... LOCK IT AND REMOVE THE KEY. THIS
WILL PREVENT THE SAW FROM STARTING UP
AGAIN WHEN THE POWER COMES BACK ON.
3. DISPLAY:
NOTE: Readout on display is in decimals. There isa
conversion chart for converting fractions to
decimals on page 55 of this manual.
MINUS
INDICATOR NUMBERS
OTOR
li
) II °#°vC n
DECIMAL POINTS
gives the user four pieces of
1. The decimal point shows what function,
oithor I::LEV OR BEVEL, io b_ing displayed.
2. The numbers show either the present
position of the blade or the entered
destination for programmed operation.
3. The minus indicator in the upper left hand
corner lights when the displayed number is
negative (less than the "zero" position) or
when the _ key is pressed after a
number.
4. The flashing IS indicates that the saw needs
calibrating. The flashing" E" will only be
displayed when the saw requires calibrating
due to either a power interruption or the saw
has been unplugged.
FLASHING "P" INDICATES
CALIBRATION REQUIRED
_OTOR __ -
4. CONTROL KEYS:
The two rows of keys directly under the display
are the control keys. They are how you tell the
computer what you want it to do.
MINUS
A. Jog key is a rocker type switch that when
pushed up and held in causes the blade to
elevate when in _ or to bevel to the left
when in _ .Themotionsaretheopposite
when thekey is pushed down.
When the jog key is pressed and immediately
released it will cause the blade to change
elevation by 0.005" or bevel by 0.1° depending
on the function selected. This "'tapping" of the
jog key can be repeated as many times as
desired to move blade into position.
B. _ and _ keys are used to select the
desired function,
Pressing _ will display current blade
elevation. Saw must be in elevation mode
before any programmed or
. jogging elevation
operation can be pertormed. A lighted
decimal above [_ key indicates that the
elevation function is active,
In the same way, pressing _ will display
the current angle of the blade and allow any
programmed or jogging bevel operation to be
performed. A lighted decimal above [_
indicates that the bevel mode is active
C. _ key is a dual purpose key. When the
saw is first plugged in or if there has been a
power interruption the key operates as a
"Calibration" key. Pressing the key, with the
24
Loading ...
Loading ...
Loading ...