Loading ...
Loading ...
Loading ...
12
The outlet can be located anywhere within the shaded area. Anywhere within the shaded
area, the minimal distance between the appliance and the wall is 13⁄4 in (45 mm).
Electrical Requirements:
A three prong grounded outlet
120 V, 60 Hz, AC only
20 Amp electrical supply with a fuse or a circuit breaker
Electric Installation
This product must be connected to a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the National Electric Code or the prevailing
local code for this rating.
The power supply cord and plug should be brought to a separate 20-amp branch circuit
single grounded outlet. The outlet box should be located inside the cabinet above the
appliance.
The outlet box and supply circuit should be installed by a qualified electrician and
conform to the National Electrical Code or the prevailing local code.
The voltage used must be the same as specified on this microwave oven. Using a higher
voltage is dangerous and may result in a fire or oven damage. Using a lower voltage will
cause slow cooking.
The manufacturer is not responsible for any damages resulting from the use of the oven
with any voltage other than specified.
6
DDiimmeennssiioonnss aanndd CCaabbiinneett RReeqquuiirreemmeennttss
General Cabinet Requirements
▯ ¼" (6.4 mm) space between the side of the appliance
and an adjacent wall or cabinet door when installed
at the end of a cabinet run.
▯ The cabinet base must be flat and capable of
supporting the weight of your appliance when in use.
See section Cabinet Dimensions.
▯ The appliance door will overlap the furniture below
by approx 3/16" (5 mm) when opened.
9 WARNING
There must be an air gap of at least ]" (6 mm)
between the appliance and the cabinet walls when
the appliance is installed, i.e. X" (3 mm) each side.
Outlet Area
The outlet can be located anywhere within the
shaded area. Anywhere within the shaded area,
the minimal distance between the appliance and
the wall is 1¾ in (45 mm).
Appliance Dimensions
Cabinet Dimensions
NOTICE: The cabinet base must be flat and
capable of supporting a weight of at least 142 lbs
(64.1 kg).
Under counter dimensions
ê
PP
ê
PP
PP
ç¼ʚ
ʎ¼ʚ
è¼ʚ
ʎ¼ʓʘ
ç¼ʓʘ
ç¼ʓʘ
è¼ʓʘ
ë
PP
ë
ʌ¼ʓʘ
ë
PP
ëé
ʌ¼ʓʘ
Installation Requirements
15
The outlet can be located anywhere within the shaded area. Anywhere within the shaded
area, the minimal distance between the appliance and the wall is 1
3
⁄4 in (45 mm).
Electrical Requirements:
A three prong grounded outlet
120 V, 60 Hz, AC only
20 Amp electrical supply with a fuse or a circuit breaker
Electric Installation
This product must be connected to a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the National Electric Code or the prevailing
local code for this rating.
The power supply cord and plug should be brought to a separate 20-amp branch circuit
single grounded outlet. The outlet box should be located inside the cabinet above the
appliance.
The outlet box and supply circuit should be installed by a qualified electrician and
conform to the National Electrical Code or the prevailing local code.
The voltage used must be the same as specified on this microwave oven. Using a higher
voltage is dangerous and may result in a fire or oven damage. Using a lower voltage will
cause slow cooking.
The manufacturer is not responsible for any damages resulting from the use of the oven
with any voltage other than specified.
6
DDiimmeennssiioonnss aanndd CCaabbiinneett RReeqquuiirreemmeennttss
General Cabinet Requirements
▯ ¼" (6.4 mm) space between the side of the appliance
and an adjacent wall or cabinet door when installed
at the end of a cabinet run.
▯ The cabinet base must be flat and capable of
supporting the weight of your appliance when in use.
See section Cabinet Dimensions.
▯ The appliance door will overlap the furniture below
by approx 3/16" (5 mm) when opened.
9 WARNING
There must be an air gap of at least ]" (6 mm)
between the appliance and the cabinet walls when
the appliance is installed, i.e. X" (3 mm) each side.
Outlet Area
The outlet can be located anywhere within the
shaded area. Anywhere within the shaded area,
the minimal distance between the appliance and
the wall is 1¾ in (45 mm).
Appliance Dimensions
Cabinet Dimensions
NOTICE: The cabinet base must be flat and
capable of supporting a weight of at least 142 lbs
(64.1 kg).
Under counter dimensions
ê
PP
ê
PP
PP
ç¼ʚ
ʎ¼ʚ
è¼ʚ
ʎ¼ʓʘ
ç¼ʓʘ
ç¼ʓʘ
è¼ʓʘ
ë
PP
ë
ʌ¼ʓʘ
ë
PP
ëé
ʌ¼ʓʘ
7
Flush installation
Flush installation also requires:
▯ two side cleats to be attached inside the
cabinet frame, recessed from the front
▯ a
5
/
16
" (8 mm) baseplate underneath the unit
body.
Electrical Installation
The model stated on the front cover is rated at 120V
AC, 60 Hz and uses a NEMA 5-20 plug to connect to
a dedicated 120 V microwave circuit.
Electrical Requirements:
▯ three prong grounded outlet
▯ 120 V, 60 Hz, AC only
▯ 20 Amp electrical supply with a fuse or a
circuit breaker
This product must be connected to a supply circuit
of the proper voltage and frequency. Wire size must
conform to the requirements of the National
Electric Code or the prevailing local code for this
rating. The power supply cord and plug should be
brought to a separate 20-amp branch circuit single
grounded outlet. The outlet box should be located
inside the cabinet above the appliance (see section
Location Requirements). The outlet box and supply
circuit should be installed by a qualified electrician
and conform to the National Electrical Code or the
prevailing local code.
The voltage used must be the same as specified on
this microwave oven. Using a higher voltage is
dangerous and may result in a fire or oven damage.
Using a lower voltage will cause slow cooking. The
manufacturer is not responsible for any damages
resulting from the use of the oven with any voltage
other than specified.
Install Appliance
Note: The appliance is heavy. It is advisable to install
it with a second person.
NOTICE: Before installing the appliance, be sure to
verify the cabinet dimensions and electrical
connections.
Mount to Cabinet
1.
Fully insert the appliance and center it. Do not kink
the electrical cable.
2.
Screw the appliance into place.
PHDVXUHPHQWVLQLQFKHVPP
7RSYLHZ
6LGHYLHZ
ê
)OXVKLQVHW
GHSWK
ë
&OHDWV
&OHDWV
è¼ʓʘ
FOHDWV
ê
ë
RSHQLQJ
FXWRXW
KHLJKW
ʎ¼ʓʘ
IOXVK
FXWRXW
KHLJKW
EDVHSODWH
ʌ¼ʓʘ
èç¼ʓʘ
ë
èç¼ʓʘ
Model Connection
Circuit
Requirements
NEMA 5-20
120 V,
60 Hz
20 Amps
Installation Requirements
MWO-CONV-24
15
The outlet can be located anywhere within the shaded area. Anywhere within the shaded
area, the minimal distance between the appliance and the wall is 1
3
⁄4 in (45 mm).
Electrical Requirements:
A three prong grounded outlet
120 V, 60 Hz, AC only
20 Amp electrical supply with a fuse or a circuit breaker
Electric Installation
This product must be connected to a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the National Electric Code or the prevailing
local code for this rating.
The power supply cord and plug should be brought to a separate 20-amp branch circuit
single grounded outlet. The outlet box should be located inside the cabinet above the
appliance.
The outlet box and supply circuit should be installed by a qualified electrician and
conform to the National Electrical Code or the prevailing local code.
The voltage used must be the same as specified on this microwave oven. Using a higher
voltage is dangerous and may result in a fire or oven damage. Using a lower voltage will
cause slow cooking.
The manufacturer is not responsible for any damages resulting from the use of the oven
with any voltage other than specified.
6
DDiimmeennssiioonnss aanndd CCaabbiinneett RReeqquuiirreemmeennttss
General Cabinet Requirements
▯ ¼" (6.4 mm) space between the side of the appliance
and an adjacent wall or cabinet door when installed
at the end of a cabinet run.
▯ The cabinet base must be flat and capable of
supporting the weight of your appliance when in use.
See section Cabinet Dimensions.
▯ The appliance door will overlap the furniture below
by approx 3/16" (5 mm) when opened.
9 WARNING
There must be an air gap of at least ]" (6 mm)
between the appliance and the cabinet walls when
the appliance is installed, i.e. X" (3 mm) each side.
Outlet Area
The outlet can be located anywhere within the
shaded area. Anywhere within the shaded area,
the minimal distance between the appliance and
the wall is 1¾ in (45 mm).
Appliance Dimensions
Cabinet Dimensions
NOTICE: The cabinet base must be flat and
capable of supporting a weight of at least 142 lbs
(64.1 kg).
Under counter dimensions
ê
PP
ê
PP
PP
ç¼ʚ
ʎ¼ʚ
è¼ʚ
ʎ¼ʓʘ
ç¼ʓʘ
ç¼ʓʘ
è¼ʓʘ
ë
PP
ë
ʌ¼ʓʘ
ë
PP
ëé
ʌ¼ʓʘ
7
Flush installation
Flush installation also requires:
▯ two side cleats to be attached inside the
cabinet frame, recessed from the front
▯ a
5
/
16
" (8 mm) baseplate underneath the unit
body.
Electrical Installation
The model stated on the front cover is rated at 120V
AC, 60 Hz and uses a NEMA 5-20 plug to connect to
a dedicated 120 V microwave circuit.
Electrical Requirements:
▯ three prong grounded outlet
▯ 120 V, 60 Hz, AC only
▯ 20 Amp electrical supply with a fuse or a
circuit breaker
This product must be connected to a supply circuit
of the proper voltage and frequency. Wire size must
conform to the requirements of the National
Electric Code or the prevailing local code for this
rating. The power supply cord and plug should be
brought to a separate 20-amp branch circuit single
grounded outlet. The outlet box should be located
inside the cabinet above the appliance (see section
Location Requirements). The outlet box and supply
circuit should be installed by a qualified electrician
and conform to the National Electrical Code or the
prevailing local code.
The voltage used must be the same as specified on
this microwave oven. Using a higher voltage is
dangerous and may result in a fire or oven damage.
Using a lower voltage will cause slow cooking. The
manufacturer is not responsible for any damages
resulting from the use of the oven with any voltage
other than specified.
Install Appliance
Note: The appliance is heavy. It is advisable to install
it with a second person.
NOTICE: Before installing the appliance, be sure to
verify the cabinet dimensions and electrical
connections.
Mount to Cabinet
1.
Fully insert the appliance and center it. Do not kink
the electrical cable.
2.
Screw the appliance into place.
PHDVXUHPHQWVLQLQFKHVPP
7RSYLHZ
6LGHYLHZ
ê
)OXVKLQVHW
GHSWK
ë
&OHDWV
&OHDWV
è¼ʓʘ
FOHDWV
ê
ë
RSHQLQJ
FXWRXW
KHLJKW
ʎ¼ʓʘ
IOXVK
FXWRXW
KHLJKW
EDVHSODWH
ʌ¼ʓʘ
èç¼ʓʘ
ë
èç¼ʓʘ
Model
Connection
Circuit
Requirements
NEMA 5-20
120 V,
60 Hz
20 Amps
Installation Requirements
MWO-CONV-24
Loading ...
Loading ...
Loading ...