Loading ...
Loading ...
Loading ...
En
27
Changing the settings
Changing the settings
Launching utilities mode
If the utilities mode is launched while the DJ application is running,
the set status may not be displayed properly.
1 Disconnect the USB cable from your computer.
2 Press the [u] switch on this unit’s rear panel to set
this unit’s power to standby.
Set this unit’s power to the standby mode.
3 While pressing both the [SHIFT] and
[PLAY/PAUSE f] buttons on the left deck, press the
[u] switch on this unit’s rear panel.
Utilities mode is launched.
4 After setting this unit to the utility settings mode,
operate the controller for the item whose settings you
want to change.
See the explanations below for the settings that can be changed.
5 Press the [u] switch on this unit’s rear panel to set
this unit’s power to standby.
To save the settings, set the [u] switch on this unit’s rear panel to
standby and quit utilities mode.
Utilities modes
The following settings can be changed:
! MIDI controller setting
! Fader start setting
! Master output attenuator level setting
! Slip mode flashing setting
! Demo mode setting
! Setting of the velocity curve in the sampler velocity mode
! Sampler velocity mode after-touch setting
! Setting of the auto standby function
! Setting of talk over function
! Setting of talk over function level
! Cut lag setting of crossfader
! Output setting of microphone to booth monitor
! Peak limiter setting
! Brightness setting of jog ring
Forcefully using the unit as the general
MIDI controller
The unit automatically changes operation as follows depending on
whether Serato DJ is running.
! When Serato DJ is running, controller operation depends on the
Serato DJ functions.
! When Serato DJ is not running, the unit operates as a general MIDI
controller.
Even though Serato DJ is running, you can forcefully operate the unit as
a general MIDI controller.
Press the [KEY LOCK] button on the left deck.
! [KEY LOCK] button off: Operation automatically changes depending
on whether or not Serato DJ is running.
! [KEY LOCK] button lit: Regardless of whether or not Serato DJ is
running, the unit is forcefully operated as a general MIDI controller.
Changing the fader start setting
The fader start function’s setting can be changed.
! By default, the fader start mode functions without the sync mode set.
Press one of the effect parameter buttons on the left
deck.
! Effect parameter 1 button lit: Fader start with the sync mode set (The
sync function is activated simultaneously when fader starting starts.)
! Effect parameter 2 button lit: Fader start without sync mode set (The
sync function is not activated simultaneously when fader starting
starts.)
! Effect parameter 3 button lit: Fader start function disabled
Setting the master output’s attenuator
level
! The default is 0 dB.
Press one of the left deck’s [HOT CUE] mode, [ROLL]
mode or [SLICER] mode buttons.
! [HOT CUE] mode button lit: 0 dB (no attenuation)
! [ROLL] mode button lit: –3 dB
! [SLICER] mode button lit: –6 dB
Changing the slip mode flashing setting
When slip mode in on, buttons available in slip mode (such as the jog
dial indicator, [AUTO LOOP] button, and [PLAY/PAUSE f] button)
can be set to flash or not flash. The flashing method used for the [SLIP]
button during slip mode changes depending on the setting.
!
By default, slip mode flashing is set to mode 1.
Press the performance pad on the left side to select a
setting.
The currently selected setting can be understood by looking at which
pad lights.
Mode 1 Mode 2 Off
! Mode 1: When slip mode is turned on, the buttons available in
slip mode flash for approximately one second. During slip mode,
the [SLIP] button flashes only while payback continues in the
background.
! Mode 2: When the slip mode is turned on, the buttons available in
slip mode flash for approximately one second. During slip mode, the
[SLIP] button continues flashing.
! Off: The buttons available in slip mode do not flash. During slip
mode, the [SLIP] button flashes only while payback continues in the
background.
Loading ...
Loading ...
Loading ...