Loading ...
Loading ...
Loading ...
OPERATING TIPS
OPERATION
1,.
2,
3,
4,,
Check the attachment clutch for correct adjustment° For the
blade(s) to disengage correctly, the adjustment must be cop
rect
Before you use the unit, check the oil inthe engine and add oil
if necessary°
if the engine wi]! not start, first make sure the wire isattached
to the spark plug
Make sure atlthebelts are insideaitthe belt guides See the in-
structions on how to remove and install the motion drive and
mower drive belts
5
64
7,
8_
9,,
Before you make an inspection, adjustment (except for thecar-
buretor) or repair, make sure the wire from the spark plug isdis-
connected°
Make sure the seat switch wire is connected Ifthe wire is not
connected, the engine will not start
For longer life of the battery, charge the battery every three
months_
Use the shift leverto change the ground speed, not the throttle
control
Belt noise can occur when the blade or clutch isengaged° This
noise is normal and does not affect the operation of the unit
MOWING AND BAGGING TIPS
1 For a lawn to lookbetter, check the cutting level of the mower 10.
housing° See "How To Level The Mower Housing" in the Ser-
vice And Adjustment section
2,,
34
4.,
Forthe mower housing tocut level, make sure the tires have
the correct amount of air pressure (PSI)
Every timeyou usethe unit, check the blade, tf the blade isbent
or damaged, immediately replace the blade Also, make sure
the nut for the blade is tight.
Keep the blade(s) sharpened_ Worn blades will cause the ends
ofthe grass to turn brown
11o
12
13.
For better engine performance and an even discharge of the
cut grass, always operate the engine with the throttle in FAST
position
When you use a bagger, operate the engine with the throttle in
FASTposition and the shift lever in first or second gear
For better cuttingperformance and a quality cut, mow with the
shift leverin one of the slower speeds
After each use, clean the bottom and top of the mower housing
for better performance Also, a clean mower housing will help
prevent afire°
5_
6.,
7_
8,,
94
Do not cut or bag grass that is wet Wet grass will not discharge
correctly. Let the grass dry before cutting,
Use the left side of the mower housing to trim near an object
Discharge the cut grass onto the mowed area. The result is a
more even discharge of cut grass
When you mow large areas, start by turning to the right so that
the cut grass wilt discharge away from shrubs, fences, drive-
ways, etc After one ortwo rounds, mow inthe opposite direc-
tion making left turns until finished (Figure 14)
Ifthe grass is very high, cut two times to decrease the load on
the engine Firstcut with the mower housing inthe highest posi-
tion and then lowerthe mower housing for the second cut
Figure14
MULCHING TIPS
When you usea mulcher attachment, the grass is cutinto very small 4
pieces° These small pieces wilt quickly break down. Because the
nutrients are returned to the soil, the lawn will need less fertilizer_Too
correctly mulch the grass, follow the steps belowo
1 Set the throttle in the FAST position. Operate the mower at a
slower ground speed If ground speed istoo fast, the grass wilt 5
not have an even cut
2. Keep a sharp edge on the blade. A blade that isnot sharp will
cause the ends of the grass to become brown_ 6.
3 Make sure the grass is dry Wet grass is difficult to cut 7
F-98668 17
Set the height of the mower housing so that only the top third
ofthe grass is cut If the grass is too high, set the height of the
mower housing to the maximum heighL Then, lower the mower
housing for the second cut. Also, instead of using the full width
of the mower housing, mulch at half the width°
Clean the bottom ofthe mower housing. Grass and otherdebris
can keep the mower from working correctty_
If the grass grows fast, mulch more often
ff an area needs improvement, mulch a second time
Loading ...
Loading ...
Loading ...