Vevor THJ3838BHYSX00001V1 Heat Press 15x15Inch 8pcs Heat Press Machine 1050W Multifunctional Sublimation Dual LED Display Heat Press Machine

USER GUIDE - Transcript

• Page 1: Email CustomerSeicevevorcom MULTIFUNCTIONAL DIGITAL HEAT PRESS MACHINE USER GUIDE
• Page 2 - English - : MULTIFUNCTIONAL DIGITAL HEAT PRESS MACHINE Be sure to review the contents of this manual before attempting to operate the equipment This manual should be located where it can be easily referenced by all users of themachine IMPORTANT NEED HELP CONTACT US Have product questions Need technical suppo Please feel free to contact us CustomerSeicevevorcom PARTS LIST 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC A B C E F G H I J D A Phillips screwdriver can be turned into a slotted screwdriver by rotating it 180 degrees Only 8 in 1 Heat Press Has Pa G Only 8 in 1 Heat Press Has Pa Only 8 in 1 Heat Press Has Pa
• Page 3 - English - : CONTENTS REPLACE BAKING COASTER HEAT PRESS MACHINE PARTS INTRODUCTION PARTS LIST ASSEMBLY amp USE STEPS INTELLIGENT TEMPERATURE CONTROLLER OPERATION METHOD Ⅰ PREPARATION BEFORE USING Ⅱ SET TEMPERATURE REQUIRED REPLACE BAKING TRAY MAT 89 REPLACE BAKING CAP MAT 1012 1314 ⅢPRINTING METHODS ⅣTROUBLE SHOOTING FOR TRANSFER QUALITY 1516 HEAT PRESS MACHINE PARTS INTRODUCTION TEMP TEMP TIME SET TIME overload protector design power switch display temperature light set light time light minus mode plus sta best pressure for heat press rotation lock screw swiveling pressure adjustment spring Tshi 3812 other object 316 316 spring object
• Page 4 - English - : CONTENTS REPLACE BAKING COASTER HEAT PRESS MACHINE PARTS INTRODUCTION PARTS LIST ASSEMBLY amp USE STEPS INTELLIGENT TEMPERATURE CONTROLLER OPERATION METHOD Ⅰ PREPARATION BEFORE USING Ⅱ SET TEMPERATURE REQUIRED REPLACE BAKING TRAY MAT 89 REPLACE BAKING CAP MAT 1012 1314 ⅢPRINTING METHODS ⅣTROUBLE SHOOTING FOR TRANSFER QUALITY 1516 HEAT PRESS MACHINE PARTS INTRODUCTION TEMP TEMP TIME SET TIME overload protector design power switch display temperature light set light time light minus mode plus sta best pressure for heat press rotation lock screw swiveling pressure adjustment spring Tshi 3812 other object 316 316 spring object
• Page 5 - English - : MULTIFUNCTIONAL DIGITAL HEAT PRESS MACHINE Be sure to review the contents of this manual before attempting to operate the equipment This manual should be located where it can be easily referenced by all users of themachine IMPORTANT NEED HELP CONTACT US Have product questions Need technical suppo Please feel free to contact us CustomerSeicevevorcom PARTS LIST 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC A B C E F G H I J D A Phillips screwdriver can be turned into a slotted screwdriver by rotating it 180 degrees Only 8 in 1 Heat Press Has Pa G Only 8 in 1 Heat Press Has Pa Only 8 in 1 Heat Press Has Pa
• Page 6 - English - : ASSEMBLY amp USE STEPS 2 3 4 5 Tighten knob Rotate the heat transfer board to the side Pull out the mat below place the clothes at on the mat and place the pattern on the clothes Turn this adjustment switch to adjust the pressure Pluck the plug Rotate the heat transfer board to the side Replace Baking Tray Mat
• Page 7 - English - : INTELLIGENT TEMPERATURE CONTROLLER OPERATION METHOD ⅡSet temperature required ⅠPreparation before Using Check the connection between power plug and electrical socket of electrical cabinetBe sure to operate with safe ground wire Heat press element must be securely plugged into the machine before you switch the machine onPlug your electrical cord into the machine Plug electrical socket into wall plugTurn the power on by ipping the OnO Switch on Nominal voltage220V Maxinput power1250W Set the temperature and time according to the table below and get the specic corresponding temperature and timing settingTemperature is measured in Degrees Fahrenheit Press the MODEbutton ONCEsee the set light turning redThen press the plusminus key to set the initial heating temperature AInitial Temperature Setting Range200450 Press the MODE button for THE SECOND TIMEsee the temperature light turning redThen press the plus or minus key to set the highest heating temperature BHighest Temperature Setting Range200450 Press the MODE button for THE THIRD TIMEsee thetime light turning red Then press the plus or minus key to set the proper heating time CProper Heating Time Setting Range0999 sec Press Object Mugs Tiles Metal board Plate Initial Temperature Highest Temperature Proper Heating Time s Sublimation paper3050s Tshi Paper1020s Tshi 230 355 06 07 Turn o the power and pull out the mat It is recommended to wear heatresistant gloves when removing clothes or remove them after 23 minutes Be careful of hot heat Printed pattern Note The machine has a self locking function for temperature setting If the staing temperature is set to 340Fthe machine will automatically limit the maximum temperature setting range from 340 to 430F Converselyif setting the maximum temperature as 250F at rstthe machine will automatically limit the staing temperature setting range from 200 to 250F Initial heating temperature alwaysltHighest heating temperature Printed clothes Press the MODEbutton for THE FOURTH TIMEnish the setting The set light is on and the temperature will continue to rise When the set maximum temperature is reached the countdown stas After the countdown ends the quotBEEFquot sound will be emitted the indicator light will turn o and the operation is completeand the machine stands by to work DFinish the Setting and Stands by to Work
• Page 8 - English - : INTELLIGENT TEMPERATURE CONTROLLER OPERATION METHOD ⅡSet temperature required ⅠPreparation before Using Check the connection between power plug and electrical socket of electrical cabinetBe sure to operate with safe ground wire Heat press element must be securely plugged into the machine before you switch the machine onPlug your electrical cord into the machine Plug electrical socket into wall plugTurn the power on by ipping the OnO Switch on Nominal voltage220V Maxinput power1250W Set the temperature and time according to the table below and get the specic corresponding temperature and timing settingTemperature is measured in Degrees Fahrenheit Press the MODEbutton ONCEsee the set light turning redThen press the plusminus key to set the initial heating temperature AInitial Temperature Setting Range200450 Press the MODE button for THE SECOND TIMEsee the temperature light turning redThen press the plus or minus key to set the highest heating temperature BHighest Temperature Setting Range200450 Press the MODE button for THE THIRD TIMEsee thetime light turning red Then press the plus or minus key to set the proper heating time CProper Heating Time Setting Range0999 sec Press Object Mugs Tiles Metal board Plate Initial Temperature Highest Temperature Proper Heating Time s Sublimation paper3050s Tshi Paper1020s Tshi 230 355 06 07 Turn o the power and pull out the mat It is recommended to wear heatresistant gloves when removing clothes or remove them after 23 minutes Be careful of hot heat Printed pattern Note The machine has a self locking function for temperature setting If the staing temperature is set to 340Fthe machine will automatically limit the maximum temperature setting range from 340 to 430F Converselyif setting the maximum temperature as 250F at rstthe machine will automatically limit the staing temperature setting range from 200 to 250F Initial heating temperature alwaysltHighest heating temperature Printed clothes Press the MODEbutton for THE FOURTH TIMEnish the setting The set light is on and the temperature will continue to rise When the set maximum temperature is reached the countdown stas After the countdown ends the quotBEEFquot sound will be emitted the indicator light will turn o and the operation is completeand the machine stands by to work DFinish the Setting and Stands by to Work
• Page 9 - English - : ASSEMBLY amp USE STEPS 2 3 4 5 Tighten knob Rotate the heat transfer board to the side Pull out the mat below place the clothes at on the mat and place the pattern on the clothes Turn this adjustment switch to adjust the pressure Pluck the plug Rotate the heat transfer board to the side Replace Baking Tray Mat
• Page 10 - English - : Replace Baking Cap Mat Pluck the plug Rotate the heat transfer board to the side Replace Baking Cap Mat Loosen the bottom screw and remove Lift the cushion up Install the baking pad Pa D
• Page 11 - English - : Replace Baking Cap Mat Pluck the plug Rotate the heat transfer board to the side Replace Baking Cap Mat Loosen the bottom screw and remove Lift the cushion up Install the baking pad Pa D
• Page 12 - English - : Select the appropriate size baking pan mat Pa A or B Plug in Patterned plate Replace Baking Tray Mat A B Use the screwdriver 4 to tighten the 2 screws just removed and put the cap on Shaped hat Replace Baking Cap Mat
• Page 13 - English - : Select the appropriate size baking coaster Pa F or G Put the cup in Pa E Install H to Pa E Tighten the screws on both sides We suggest to tighten the screws on the side ① rst and then tighten the screws on the side ② Adjust the tightness Plug in Shaped cup Replace Baking Coaster E H F or G E ① ② CAUTION CHECK the correct voltage before using the machineBe SURE to operate with reliable grounded protection connections TURN OFF the machineand then DISCONNECT the powersupply before replacing the heat unitsDO NOT forget to wearing insulated gloves if the unit is still under hightemperature AVOID prolonged burning of the heating pasIf not turning the power o please place a hot stamping replacement it could be a scrap and can be used repeatedly AVOID damaging the heating units with sharp pas of the stamping object AVOID touching the heating units and the compression spring without protection in case of potential damageof body during use If its hard to pushing the graspplease adjust the rotation lock screw in order to reduce the pressure of compression springOr it will damage to the strength of the machine Before lifting the machineplease lock the machine head by rotation lock screw and loosen the handledont screw the rotation lock screw too tightBesides do not put down the machine beyond the limitWhen meeting the falling limit you can feel an obvious pressure on the swiveling pressure adjustment wheel Keep children away from the machine DO NOT attempt to press products that are not intended for normal heat transfer Baking pads should be avoided of empty burning
• Page 14 - English - : E And install I or J to Pa E Tighten the screws on both sides We suggest to tighten the screws on the side ① rst and then tighten the screws on the side ② Adjust the tightness Plug in Put the cup in Pa E Shaped cup Replace Baking Coaster I or J E ① ② ⅢPrinting methods Ⅳ Trouble shooting for transfer quality Pale ColorThe temperature is too lowthe pressure is not corrector not pressed long enough Blurring PatternToo much transfer time causes proliferation Pa Blurring of PatternHeat was not distributed correctly through heat plate Allow more time between press operationsPressure distribution can also be the causewhich can be set on the four plate suace adjustersPlease note that it has been facto set and there should be no need to adjust them Dull Suace of PatternThe pressure is too lager or the temperature is too high Scarred PatternTransfer time is too long Dierent Pattern ColorThe pressure is not correct or the transfer paper is poor quality Adhesive Paperthe temperature is too high or poor printing ink Adjust pressure to your requirement Neither too tight nor too loose Plug in the power cord and turn the power switch ON The temperature stas to riseSet the Initial temperatureHighest Temperature an press time Once the temperature rise to the Initial temperaturethe buzzer will send out a shot BEEF sound Press the button onceThen Place the object ie T shi on press bedPull down the handle to press the object Wait for the time ends up with a long buzzer soundNote There will be about 5s time for long buzzer to notify you it has nishedand after that will appear 5s for shobuzzer to notify you whether you still go on the next workif not the temperature will fall down to the Initial temperature Work nish and take out object Turn o the power switch
• Page 15 - English - : E And install I or J to Pa E Tighten the screws on both sides We suggest to tighten the screws on the side ① rst and then tighten the screws on the side ② Adjust the tightness Plug in Put the cup in Pa E Shaped cup Replace Baking Coaster I or J E ① ② ⅢPrinting methods Ⅳ Trouble shooting for transfer quality Pale ColorThe temperature is too lowthe pressure is not corrector not pressed long enough Blurring PatternToo much transfer time causes proliferation Pa Blurring of PatternHeat was not distributed correctly through heat plate Allow more time between press operationsPressure distribution can also be the causewhich can be set on the four plate suace adjustersPlease note that it has been facto set and there should be no need to adjust them Dull Suace of PatternThe pressure is too lager or the temperature is too high Scarred PatternTransfer time is too long Dierent Pattern ColorThe pressure is not correct or the transfer paper is poor quality Adhesive Paperthe temperature is too high or poor printing ink Adjust pressure to your requirement Neither too tight nor too loose Plug in the power cord and turn the power switch ON The temperature stas to riseSet the Initial temperatureHighest Temperature an press time Once the temperature rise to the Initial temperaturethe buzzer will send out a shot BEEF sound Press the button onceThen Place the object ie T shi on press bedPull down the handle to press the object Wait for the time ends up with a long buzzer soundNote There will be about 5s time for long buzzer to notify you it has nishedand after that will appear 5s for shobuzzer to notify you whether you still go on the next workif not the temperature will fall down to the Initial temperature Work nish and take out object Turn o the power switch
• Page 16 - English - : Select the appropriate size baking coaster Pa F or G Put the cup in Pa E Install H to Pa E Tighten the screws on both sides We suggest to tighten the screws on the side ① rst and then tighten the screws on the side ② Adjust the tightness Plug in Shaped cup Replace Baking Coaster E H F or G E ① ② CAUTION CHECK the correct voltage before using the machineBe SURE to operate with reliable grounded protection connections TURN OFF the machineand then DISCONNECT the powersupply before replacing the heat unitsDO NOT forget to wearing insulated gloves if the unit is still under hightemperature AVOID prolonged burning of the heating pasIf not turning the power o please place a hot stamping replacement it could be a scrap and can be used repeatedly AVOID damaging the heating units with sharp pas of the stamping object AVOID touching the heating units and the compression spring without protection in case of potential damageof body during use If its hard to pushing the graspplease adjust the rotation lock screw in order to reduce the pressure of compression springOr it will damage to the strength of the machine Before lifting the machineplease lock the machine head by rotation lock screw and loosen the handledont screw the rotation lock screw too tightBesides do not put down the machine beyond the limitWhen meeting the falling limit you can feel an obvious pressure on the swiveling pressure adjustment wheel Keep children away from the machine DO NOT attempt to press products that are not intended for normal heat transfer Baking pads should be avoided of empty burning