Loading ...
Loading ...
Loading ...
10
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
5.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to a correctly installed and eciently
earthed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
electrician.
5.4 Setting up the appliance
Please note!
• Coee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the instructions in section “17. Setting water
hardness”.
1. Plug the power cord (C8) connector into the socket (A20) at
the back of the appliance and connect the appliance to the
mains electricity supply (g. 1). Make sure the main switch
(A21) at the back of the appliance is pressed (g. 2);
2. “SELECT LANGUAGE”: Press the selection arrow (B2) corre-
sponding to the required language;
then follow the instructions which appear on the appliance
display:
3. “FILL TANK WITH FRESH WATER”: remove the water tank
(A16) (g. 3), open the lid (A15) (g. 4), ll to the MAX line
with fresh water (g. 5), close the lid and put the tank back
in the appliance (g. 6);
4. “INSERT WATER SPOUT”: Check that the hot water/steam
spout (C6) is inserted on the connection nozzle (A9) (g. 7)
and place a container holding a minimum of 100 ml under-
neath (g. 8);
5. “WATER CIRCUIT EMPTY PRESS OK TO START” appears on
the display;
6. Press the selection arrow corresponding to “OK ” to
conrm. The appliance delivers hot water from the hot
water spout (g. 8) then goes o automatically.
The coee machine is now ready for normal use.
Please note!
• When setting up the appliance, you need to make 4-5 cups
of coee or 4-5 cappuccinos before the appliance starts to
give satisfactory results.
• When making the rst 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
• To improve the performance of your appliance, we recom-
mend installing a water softener lter (C4) as described
in section “18. Water softener lter”. If your model is not
provided with a lter, you can request one from De’Longhi
Customer Services.
6. TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch
(A21) is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
(A8) and is collected in the drip tray (A14) underneath. Avoid
contact with splashes of water.
• To turn the appliance on, press the
button (A7-g.
9). The message “HEATING UP UNDERWAY PLEASE WAIT”
appears on the display.
As well as heating the boiler, this also heats the internal circuits
by circulating hot water. The appliance is at temperature when
the main screen (homepage) appears.
7. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts
(A8). Avoid contact with splashes of water.
• To turn the appliance o, press the button (A7-g.
9).
• The message “TURNING OFF UNDERWAY, PLEASE WAIT”
appears on the display, then (if envisaged) the appliance
performs a rinse cycle and goes o (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• rst turn the appliance o by pressing the button
(g. 9);
Loading ...
Loading ...
Loading ...