Loading ...
Loading ...
Loading ...
u
Press the pin
Fig. 5 (3)
out from underneath.
u
Press the soft stop bracket
Fig. 5 (4)
towards the door.
u
Fully detach the cover
Fig. 5 (5)
on the hinge side and
remove it.
u
Remove the faceplate
Fig. 5 (1)
.
u
Using a screwdriver, detach the
cover on the handle side
Fig. 6 (6)
and draw it outwards for
removal.
Fig. 6
u
Unscrew the soft stop unit (2x Torx® 15)
Fig. 5 (7)
.
u
Pull the soft stop unit out a little, push it in the direction of the
handle side and swing it out.
u
Set the soft stop unit aside.
u
Unscrew the bearing
element
Fig. 5 (8)
, turn it
180° and transfer it to the
opposite side. Possibly
make preliminary holes with
a bradawl or use a cordless
screwdriver.
Fig. 7
4.3.2 Detaching the upper door
Fig. 8
u
Close the upper door.
u
Pull off the cover
Fig. 8 (10)
forwards and upwards.
u
Lift off the cover
Fig. 8 (11)
.
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
u
Unscrew the upper turn hinge
Fig. 8 (12)
(2x Torx® 25)
Fig. 8 (13)
and lift it off.
u
Lift off the upper door and set it aside.
4.3.3 Detaching the lower soft stop mechanism
Fig. 9
u
Open the lower door.
NOTICE
Risk of damage!
If the door seal is damaged, the door may fail to close properly
and the cooling will be inadequate.
u
Do not damage the door seal with the screwdriver!
u
Disengage and remove the faceplate
Fig. 9 (20)
using a flat-
blade screwdriver.
w
The faceplate is attached over the soft stop bracket.
Fig. 10
u
Slide the faceplate forwards over the soft stop bracket
Fig. 10 (24)
in the direction of the appliance.
u
Snap the safety lock
Fig. 10 (22)
into the oblong hole.
w
The safety lock prevents the hinge from snap-closing.
u
Using a screwdriver, lift off the cover
Fig. 10 (21)
from the
outside and remove it in an outward direction.
u
If necessary, tip the appliance backwards with the assis-
tance of a second person.
u
Press the pin
Fig. 10 (23)
out from underneath.
u
Press the soft stop bracket
Fig. 10 (24)
towards the door.
u
Remove the faceplate
Fig. 10 (20)
.
u
Unscrew the entire soft stop unit (2x Torx® 15)
Fig. 10 (25)
.
u
Pull the soft stop unit out a little, push it in the direction of the
handle side and swing it out.
u
Set the soft stop unit aside.
4.3.4 Detaching the lower door
u
Close the lower door.
u
Draw the middle bearing pin
Fig. 11 (32)
together with the
washer
Fig. 11 (34)
out of the turn hinge and lower door.
u
Remove the plastic cap
Fig. 11 (33)
.
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
u
Open the lower door.
u
Unscrew the middle turn hinge (2x Torx® 25).
Fig. 11 (31)
u
Lift off the lower door and set it aside.
Putting into operation
* Depending on model and options 7
Loading ...
Loading ...
Loading ...