Loading ...
Loading ...
Loading ...
Fig. 18
u
Attach the faceplate
Fig. 18 (1)
to the soft stop bracket
Fig. 18 (4)
so that the catches face inwards and the front
faces the appliance.
u
Slide on the cover
Fig. 18 (5)
from the outside (A) and swivel
it over the bearing element
Fig. 18 (8)
(B).
u
Attach the cover
Fig. 18 (5)
and engage it as far as the first
detent.
w
The openings for the pin are on top of one another after the
soft stop bracket has been positioned.
u
Draw the soft stop bracket
Fig. 18 (4)
towards the bearing
element and insert the pin
Fig. 18 (3)
from above so that the
square is seated in the depression.
u
Now completely snap the cover
Fig. 18 (5)
onto the bearing
element
Fig. 18 (8)
.
w
Pay attention that the cover fits properly so that the door
closes properly and the pin is secured.
u
Twist the safety lock
Fig. 18 (2)
for removal.
u
Snap thefaceplate
Fig. 18 (1)
onto the door.
u
Turn the cover
Fig. 6 (6)
through 180°, attach and engage it
on the handle side.
4.3.14 Aligning the doors
u
If necessary, align the doors to the appliance housing by
way of the two oblong holes in the bottom turn hinge
Fig. 13 (45)
and middle turn hinge
Fig. 11 (31)
. To do so,
unscrew the middle screw in the bottom turn hinge
Fig. 13 (45)
.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What
is more, the door may not close and therefore the appliance
may fail to cool properly.
u
Screw the turn hinges firmly into place with 4 Nm.
u
Check all of the screws and retighten if necessary.
4.4 Water connection
WARNING
Danger of electric shock!
u
Disconnect the appliance by unplugging it before you
connect it to the water line.
u
Shut off the water supply before you connect the water feed
lines of the IceMaker.
u
The connection to the drinking water system may be carried
out only by a qualified gas fitter and plumber.
WARNING
Risk of poisoning!
u
The water quality has to comply with the drinking water ordi-
nance of the respective country (e.g. 98/8
u
Connect to the drinking water supply only.
u
The IceMaker serves exclusively for making ice cubes in
household quantities and has to be operated with water suit-
able for the purpose.
Fig. 19
- The water pressure has to be between 0.15 MPa and
0.6 MPa (1.5 bar - 6 bar).
- The water supply to the appliance must be via a cold water
pipe which withstands the operating pressure and complies
with the hygiene regulations.
Use the accompanying stainless steel hose (1.5 m). Do not
reuse old hoses. A 3 m hose is available from the customer
service department and has to be fitted by an expert.
In the hose connecting piece is a sieve with seal.
- Between the hose and the domestic water connection there
has to be a stopcock to interrupt the water supply in case of
need.
- All the fixtures and fittings used for water supply have to
comply with the applicable regulations of the respective
country.
- Do not damage or kink the water inlet pipe when installing
the appliance.
Fig. 20
u
Connect the straight part of the accompanying stainless
steel hose to the stopcock.
The solenoid valve is at the bottom back of the appliance. It
has a metric R3/4 connecting thread.
u
Connect the angled part of the stainless steel hose to the
solenoid valve.
Putting into operation
10 * Depending on model and options
Loading ...
Loading ...
Loading ...