Loading ...
Loading ...
Loading ...
19
the openings at the side
for more than a minute
(g. 34).
4. Extract the tank from the
appliance and ll with
water.
5. Insert the lter in the
water tank and immerse
it completely for about
ten minutes, sloping it to
enable the air bubbles to
escape (g. 35).
6. Insert the lter in the l-
ter housing and press as
far as it will go (g. 36A)
7. Close the tank with the
lid, then put the tank
back in the machine (g.
36B).
When you install the lter,
you must notify the appliance
of its presence.
8. Press the MENU/ESC button to enter the menu;
8. Press the HOT MILK or LATTE button (g. 8) until “Install
lter” is displayed;
10. Press the button;
11. The message “Enable?” is displayed.
12. Press the button to conrm the selection. “Hot
water Conrm?” is displayed;
13. Position a container under the hot water spout (min. ca-
pacity: 500 ml);
14. Press the button to conrm the selection. The
appliance begins hot water delivery and the message
“Please wait” is displayed;
15. After delivery, the appliance returns automatically to the
“Ready for coee” position.
The new lter is active. You can now use the coee maker.
Replacing the lter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or when the appliance has not been used for 3
weeks, you should replace the lter:
1. Extract the tank and exhausted lter;
2. Take the new lter out of its packet and proceed as
illustrated in points 2, 3, 4, 5 and 6 in the previous section.
3. Position a container with a minimum capacity of 500 ml
under the hot water spout.
4. Press the MENU/ESC button to enter the menu;
5. Press the HOT MILK or LATTE button until “Replace lter
“ is displayed.
6. Press the button;
7. The message “Conrm?” is displayed.
8. Press the button to conrm the selection;
9. “Hot water… Conrm?” is displayed.
10. Press the button to conrm the selection. the
appliance begins delivering hot water and the message
“Please wait “ is displayed.
11. After delivery, the appliance returns automatically to the
“ready for coee” position.
The new lter is now active and you can use the coee maker.
Removing the lter
If you want to continue using the appliance without a lter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted lter;
2. Press the MENU/ESC button to enter the menu;
3. Press the HOT MILK or LATTE button (g. 8) until “Install
lter Enabled” is displayed;
4. Press the button
5. “Disable?” is displayed;
6. Press the button to conrm and the MENU/ESC
button to exit the menu.
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 15 bar
Water tank capacity: 2.0 litres max.
Size Lxhxd: 238x350x445 mm
Cable length: 1.80 m
Weight: 11.8 kg
Beans container capacity: 250 g max.
The appliance complies with the following EC
directives:
• ECRegulation1275/2008forstandby;
• Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMCdirective2004/108/ECandsubsequentamendments
• Materialsandaccessoriescomingintocontactwithfood
conform to eec regulation 1935/2004.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with hou-
sehold waste, but taken to an authorised waste se-
paration and recycling centre.
33
35
36A
36B
Loading ...
Loading ...
Loading ...