5713221861/10.13
DE
GB
ECAM28.46X
BEAN TO CUP ESPRESSO AND
CAPPUCCINO MACHINE
Instruction for use
2
A1
A
A2
A11
A12
A13
A14
A15
A17
A19
A16
A22
A3
A4
A7
A8
A9
A10
A18
A21
A20
A5
A6
2
B2
B7 B13
B8 B9 B10 B11 B12
B3 B4 B5 B6
D1
D2
A18
D3 D4
D5 D6
B1
B
C D
C1
C2
C3
C4
3
A1
A
A2
A11
A12
A13
A14
A15
A17
A19
A16
A22
A3
A4
A7
A8
A9
A10
A18
A21
A20
A5
A6
3
4
4
1 234
5 678
910
11 12
13 14 15
16
17 18 19 20
21 22 23 24
26 27 28
30 31 32
25
29A
29B
PUSH
PUSH
B
A
A B
5
5
1 234
5 678
910
11 12
13 14 15
16
17 18 19 20
21 22 23 24
26 27 28
30 31 32
25
29A
29B
PUSH
PUSH
B
A
A B
6
CONTENTS
INTRODUCTION ....................................................... 7
Symbols used in these instructions .................................7
Letters in brackets ...........................................................7
Troubleshooting and repairs ...........................................7
SAFETY ................................................................... 7
Fundamental safety warnings.........................................7
DESIGNATED USE ..................................................... 7
INSTRUCTIONS ........................................................ 7
DESCRIPTION .......................................................... 8
Description of the appliance ...........................................8
Description of the control panel ......................................8
Description of the milk container ....................................8
Description of the accessories .........................................8
PRELIMINARY CHECKS ............................................. 8
Checking the appliance ...................................................8
Installing the appliance ..................................................8
Connecting the appliance ...............................................9
Using the appliance for the rst time ..............................9
TURNING THE APPLIANCE ON ................................... 9
TURNING THE APPLIANCE OFF .................................. 9
MENU SETTINGS .................................................... 10
Rinsing ..........................................................................10
Descale .........................................................................10
Install lter ...................................................................10
Replacing the lter .......................................................10
Adjust time ...................................................................10
Auto-start .....................................................................10
Auto-O ........................................................................10
Cup warmer ..................................................................10
Energy Saving ...............................................................11
Setting the temperature ...............................................11
Setting water hardness .................................................11
Beep .............................................................................11
Setting the language ...................................................11
Cup lighting ..................................................................11
Default values (reset) ....................................................11
Statistics function .........................................................12
MAKING COFFEE .................................................... 12
Selecting the coee taste ..............................................12
Selecting the quantity of coee in the cup ...................12
Customising the “my coee” quantity ...........................12
Adjusting the coee mill ...............................................12
Tips for a hotter coee ..................................................12
Making coee using coee beans .................................12
Making coee using pre-ground coee ........................13
MAKING DRINKS WITH MILK................................... 13
Filling and attaching the milk container .......................13
Adjusting the amount of froth ......................................14
Making drinks with milk automatically .........................14
Cleaning the milk frother with the CLEAN button ........14
Programming the quantity of coee and milk in the cup
for the CAPPUCCINO, LATTE, FLAT WHITE and HOT MILK
buttons ........................................................................14
Delivering hot water ....................................................15
Change the quantity of water delivered automatically. 15
Delivering steam ...........................................................15
Tips for using steam to froth milk ..................................15
Cleaning the spout after use .........................................15
CLEANING ............................................................. 15
Cleaning the coee grounds container ..........................15
Cleaning the drip tray and condensate tray ...................16
Cleaning the inside of the coee maker ........................16
Cleaning the water tank ................................................16
Cleaning the coee spouts ............................................16
Cleaning the pre-ground coee funnel .........................16
Cleaning the infuser ......................................................16
Cleaning the milk container ..........................................17
Cleaning the hot water/steam nozzle ...........................17
DESCALE ............................................................... 17
SETTING WATER HARDNESS .................................... 18
Measuring water hardness ............................................18
Set water hardness .......................................................18
WATER FILTER ....................................................... 18
Installing the lter ........................................................18
Replacing the lter .......................................................19
Removing the lter .......................................................19
TECHNICAL SPECIFICATION ..................................... 19
DISPLAYED MESSAGES ........................................... 20
TROUBLESHOOTING ............................................... 21
ELECTRICAL CONNECTION UK ONLY ....................... 23
7
INTRODUCTION
Thank you for choosing this automatic espresso and cappuccino
machine.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the machine.
Symbols used in these instructions
Important warnings are identied by these symbols.
It is vital to respect these warnings.
Danger!
Failure to observe the warning could result in life threatening
injury from electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds.
Please note:
This symbol identies important advice or information for the
user.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on pages 2 and 3.
Troubleshooting and repairs
In the event of problems, rst try and resolve them following
the information given in the section “Displayed messages” on
page 20 and “Troubleshooting” on page 21.
If this does not resolve the problem or you require further
information, you should consult Customer Experience by calling
the number given on the annexed “Customer Experience” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
If repairs are required, contact De’Longhi Customer Experience
only. Contact details are given in the guarantee certicate
provided with the appliance.
SAFETY
Fundamental safety warnings
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore respect the following safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplugdirectlyfromtheplugonly.
Never pull the power cable as you could damage it.
• Todisconnecttheappliancecompletely,releasethemain
switch at the back of the appliance by pressing it.
• Iftheapplianceisfaulty,donotattempttorepair.
Turn it o, unplug from the mains socket and contact
Customer Experience.
• Iftheplugorpowercableisdamaged,itmustbereplaced
by De’Longhi Customer Experience only to avoid all risk.
Important!
• Keepallpackaging(plasticbags,polystyrenefoam)away
from children.
• Theapplianceisnotintendedforusebypersons(includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety. Children must be supervised to ensure they do not
play with the appliance.
Danger: Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
DESIGNATED USE
This appliance is designed and made to prepare coee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
This is an household appliance only.
It is not intended to be used in:
• sta kitchen areas in shops, oces and other working
environments;
• farmhouses;
• by clients in hotels, motels and other residential type
environments;
• bedandbreakfasttypeenvironments.
INSTRUCTIONS
Read these instructions carefully before using the appliance.
- Failure to follow these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
8
Please note:
Keep these instructions.
If the appliance is passed to other persons, they must also be
provided with these instructions.
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Beans container lid
A2. Top lid
A3. Grinding adjustment dial
A4. Beans container
A5. Pre-ground coee funnel lid with pressure lock
A6. Pre-ground coee funnel
A7. Main switch
A8. Socket for power cable connector
A9. Infuser
A10. Infuser door
A11. Cup warmer shelf
A12. Control panel
A13. Coee spout (adjustable height)
A14. Hot water and steam nozzle
A15. Condensate tray
A16. Water tank lid
A17. Water tank
A18. Water lter (some models only)
A19. Cup tray
A20. Drip tray water level indicator
A21. Drip tray
A22. Coee grounds container
Description of the control panel
(page 2 - B )
A number of buttons on the panel have a double function. This is
indicated in brackets in the description.
B1. button: turns the appliance on and o
B2. : button: to select the coee quantity
B3. MENU button to access the menu (When in the settings
MENU, it acts as the “ESC” button to exit from the selected
function and go back to the main menu).
B4. Display: guides the user in using the appliance.
B5.
button: to deliver hot water (When in the settings
menu, press to conrm the selection)
B6. button: to make 1 cup of coee with the settings
displayed
B7. aroma selection button: to select the coee
taste
B8. CAPPUCCINO button: to deliver a cappuccino
B9. LATTE button: to deliver a latte (When in the settings
menu, press to scroll backwards)
B10. FLAT WHITE button: to deliver a at white
B11. HOT MILK button: to deliver a cup of hot milk (When in
the settings menu, press to scroll forwards)
B12: button: to deliver steam
B13. button: to make 2 cups of coee with the
settings displayed
Description of the milk container
(page 2 - C )
D1. Froth adjustment and CLEAN dial
D2. Frothed milk spout (adjustable)
D3. Milk intake tube
D4. Milk container
Description of the accessories
(page 2 - D )
D1. Pre-ground coee measure
D2. Cleaning brush
A18. Water lter (certain models only)
D3. Cappuccino maker/hot water spout
D4. Power cable
D5. “Total Hardness Test” indicator paper
D6. Descaler
PRELIMINARY CHECKS
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Experience.
Installing the appliance
Important!
When installing the appliance, respect the following safety
warnings:
• The appliance gives o heat.
After positioning the appliance on the worktop, leave a
space of at least 3 cm between the surfaces of the appli-
ance and the side and rear walls and at least 15 cm above
the coee maker.
• Water penetrating the coee maker could cause damage.
Do not place the appliance near taps or sinks.
• Theappliancecouldbedamagedifthewateritcontains
freezes.
Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrangethepowercableinsuchawaythatitcannotbe
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
9
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an earthed and correctly installed
socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
professional.
Using the appliance for the rst time
Please note!
• Coee has been used to factory test the appliance and it
is therefore completely normal for there to be traces of
coee in the mill.
The machine is, however, guaranteed to be new.
• You should customise water hardness as soon as possible
following the instructions in the section “Setting the wa-
ter hardness” on page 18.
1. Insert the power cable connector into the socket at the
back of the appliance and connect the appliance to the
mains electricity supply (g. 1). Make sure the main
switch at the back of the appliance is pressed (g. 2).
Select the desired language by scrolling forwards or backwards
using the HOT MILK or LATTE button, or alternatively waiting
for the language options to scroll automatically on the display
(about every 3 seconds):
2. When “English” appears, press and hold the
button (g. 3) for a few seconds until “English set” is dis-
played.
Follow the instructions displayed by the appliance:
3. “FILL TANK!”: remove the water tank (g. 4), ll to the
MAX line with fresh water (g. 5) then replace in the ap-
pliance.
4. “INSERT WATER SPOUT!”: Check that the hot water spout is
inserted on the nozzle and place a container with a mini-
mum capacity of 100 ml underneath (g. 6).
5. “Hot water... Press OK?” is displayed;
6. Press the button to conrm (g. 3). The appliance
delivers water from the spout then goes o automatically.
The coee maker is now ready for normal use.
Please note!
• When using the appliance for the rst time, you need to
make 4-5 cups of coee or 4-5 cappuccinos before the ap-
pliance starts to give satisfactory results.
• When making the rst 5-6 cappuccinos, it is normal to
hear the noise of boiling water. After this, the noise be-
comes less.
• To enjoy your coee even more and improve the perfor-
mance of your appliance, we recommend installing a
water softener lter as described in the section “INSTALL
FILTER”. If your model is not provided with a lter, you can
request one from De’Longhi Customer Services.
TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch on
the back of the appliance is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
• To turn the appliance on, press the button (g. 7).
The message “Heating up... Please wait” is displayed.
After heating, the message “Rinsing...” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance has reached the required temperature when a
message is displayed indicating the coee taste and quantity.
TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts.
Avoid contact with splashes of water.
To turn the appliance o, press the button (g. 7). The ap-
pliance performs a rinse cycle, then the message “Turning o
underway Please wait...” is displayed and the appliance goes
o (standby).
Please note!
If the appliance is not used for an extended period, switch o
the machine at the main switch.
• rst turn the appliance o by pressing the button
(g. 8);
10
• release the main switch at the side of the appliance (g.
2).
Important!
Never press the main switch while the appliance is on.
MENU SETTINGS
When you access the programming menu by pressing the
MENU/ESC button, the following menu items are available:
Rinsing
Use this function to deliver hot water from the spout to heat
the internal circuit and make the coee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Rins-
ing” is displayed;
3. Press the button. The message “Conrm?” is dis-
played;
4. Press the (g. 3): after a few seconds, hot water
ows out of the spout, heating the internal circuit and ma-
king the coee delivered hotter.
Please note!
Press any button to stop hot water delivery at any time.
Descale
For instructions on descaling, see page 17.
Install lter
For instructions on how to install the lter, see the section
“Installing the lter (page 18).
Replacing the lter
For instructions on how to replace the lter, see the section
“Replacing the lter” (page 19).
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Adjust
time” is displayed;
3. Press the button (g. 3);
4. Press the HOT MILK or LATTE button (g. 8) to change
the hours;
5. Press the button to conrm;
6. Press the HOT MILK or LATTE button (g. 8) to change
the minutes;
7. Press the button to conrm.
This sets the time. Press the MENU/ESC button to exit the
menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already have been set
correctly.
To enable Auto-on, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Au-
to-start” is displayed;
3. Press the button. “Enable?” is displayed;
4. Press the button to conrm;
5. Press the HOT MILK or LATTE button to choose the hours;
6. Press the button to conrm;
7. Press the HOT MILK or LATTE button (g. 8) to change
the minutes;
8. Press the button to conrm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been conrmed, enabling of auto-start is in-
dicated by the symbol displayed alongside the time and
under the Auto-start item in the menu.
To disable the function:
1. Select auto-start from the menu;
2. Press the button. “Disable?” is displayed;
3. Press the button to conrm.
The symbol is no longer displayed.
Auto-O
The time can be changed so that the appliance switches o
after 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-o, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Au-
to-o” is displayed;
3. Press the button;
4. Press the HOT MILK or LATTE button (g. 8) until the de-
sired operation time is displayed (15 or 30 minutes, or 1, 2
or 3 hours);
5. Press the button to conrm;
6. Press the MENU/ESC button to exit the menu.
Auto-o is programmed.
Cup warmer
This function enables or disables the cup warmer.
Proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Cup
warmer” appears on the display;
11
3. Press the button. “Disable?” is displayed (or “En-
able?” if the function has been disabled);
4. Press the button to disable (or enable) the func-
tion.
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coee hot.
Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) “energy saving” mode, proceed as
follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Energy
saving” is displayed;
3. Press the button. “Disable?” is displayed (or “En-
able?” if the function has been disabled);
4. Press the button to disable (or enable) energy
saving mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is enabled, if the machine is not used for
about 1 minute, “Energy Saving” is displayed.
Please note!
• When in energy saving mode, a few seconds elapse
before the rst coee, cappuccino or milk based coee is
delivered as the appliance must heat up again.
• To prepare any drink, press any button to exit energy
saving, then press the button corresponding to the drink
you want to make.
• If the milk container is inserted,“Energy saving” is not
activated.
Setting the temperature
To modify the temperature of the water used to make the cof-
fee, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Set
temperature” is displayed;
3. Press the button;
4. Press the HOT MILK or LATTE button until the required
temperature (●= low; ●●●●= high) is displayed;
5. Press the button to conrm;
6. Press the MENU/ESC button to exit the menu.
Setting water hardness
For instructions on setting water hardness, see page 20.
Beep
This enables or disables the beep emitted by the machine
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.
To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Beep”
is displayed;
3. Press the button. “ Disable?” or “ Enable?” is dis-
played;
4. Press the button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
Setting the language
To change the language for the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Set
language” is displayed;
3. Press the button;
4. Press the HOT MILK or LATTE button until the required
language is displayed;
5. Press the button to conrm;
6. A message conrming the language installed is displayed;
7. Then press the MENU/ESC button to exit the menu.
Cup lighting
This function enables or disables the cup lighting. The lighting
is enabled by default.
The lights come on each time coee and drinks with milk are
made and during each rinse cycle.
To disable or re-enable this function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Cup
lighting” is displayed.
3. Press the button. “ Disable?” or “ Enable?” is dis-
played;
4. Press the button to enable or disable the cup
lighting;
5. Press the MENU/ESC button to exit the menu.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as previously set).
To reset the default values, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “De-
fault values” is displayed;
3. Press the button;
4. The message “Conrm?” is displayed.
12
5. Press the button to conrm and exit.
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Statis-
tics” is displayed;
3. Press the button;
4. Press the HOT MILK or LATTE button (g. 8) to verify:
- how many coees have been made;
- the total number of cappuccinos and milk based coees
made;
- the total number of litres of water delivered;
- how many times the machine has been descaled;
- how many times the water softener lter has been re-
placed.
5. Press the MENU/ESC button twice to exit the menu.
MAKING COFFEE
Selecting the coee taste
he appliance is set by default to make coee with a standard
taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the button (g. 9) repeat-
edly until the required taste is displayed.
Selecting the quantity of coee in the cup
The appliance is set by default to make a standard quantity of
coee. To select the quantity of coee, press the
button (g. 10) until the message corresponding to the
required quantity of coee is displayed:
Coee selected Quantity in cup (ml)
MY COFFEE Programmable:
from ≃20 to ≃180
SHORT
≃40
STANDARD
≃60
LONG
≃90
EXTRA LONG
≃120
Customising the “my coee” quantity
The appliance is set by default to automatically deliver 30 ml
of “my coee”.
To modify this quantity, proceed as follows:
1. Place a cup under the coee spouts (g. 14).
2. Press the button (g. 10) until “MY COFFEE”
is displayed.
3. Keep the button (g. 11) pressed until the message
“1 MY COFFEE Program quantity” is displayed and coee
delivery begins. Release the button.
4. As soon as the coee in the cup reaches the required level,
press the button (g. 11) again.
The quantity of coee in the cup has now been programmed.
Adjusting the coee mill
The coee mill is preset in the factory to make coee correctly
and should not require adjusting initially.
However, if after making the rst few coees you nd that the
coee is too thin and not creamy enough or that delivery is too
slow (a drop at a time), this can be corrected by adjusting the
grinding adjustment dial (g. 12).
Please note!
The grinding adjustment dial must only be turned when the
coee mill is in operation.
If the coee is delivered too slowly or
not at all, turn one click clockwise to-
wards “7”.
For fuller bodied creamier coee on the
other hand, turn one click anticlockwise
towards “1” (do not turn more than one
click at a time otherwise the coee could be delivered a drop
at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered.
If this adjustment does not obtain the desired result, turn the
dial another click.
Tips for a hotter coee
For a hotter coee, before delivery you are recommended to:
• perform a rinse cycle by selecting the “Rinsing” function in
the settings menu (page 10)
• warm the cups with hot water (using the hot water
function);
• increase the coee temperature in the settings menu
(page 11).
Making coee using coee beans
Important!
Do not use caramelised or candied coee beans as they could
stick to the coee mill and make it unusable.
1. Place coee beans in the coee bean container (g. 13).
13
2. Place under the coee dispensing spouts, either:
- 1 cup if you want one coee (g. 14);
- 2 cups if you want 2 coees.
3. Lower the spouts as near as possible to the cup. This
makes a creamier coee (g. 15).
4. Press the button corresponding to the number of coees
required (1 cup or 2 cups , gs. 11 and
16).
5. Preparation begins. The amount of coee selected is dis-
played together with a progress bar which gradually lls
as preparation progresses.
Please note:
• While the machine is making coee, delivery can be inter-
rupted at any moment by pressing any button.
• At the end of delivery, to increase the quantity of coee
in the cup, just press (within 3 seconds) one of the coee
buttons ( or ).
Once the coee has been made, the appliance is ready to make
the next drink.
Please note!
• Various alarm messages could be displayed while using
the machine (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in the section “Displayed
messages” (page 20).
• For hotter coee, see the section “Tips for a hotter coee”
(page 12).
• If the coee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in the “Trouble-
shooting” section on page 21.
Making coee using pre-ground coee
Important!
• Never add pre-ground coee
when the machine is o or it
could spread through the inside
of the machine and dirty it.
This could damage the
appliance.
• Neverusemorethan1levelmeasureoritcoulddirtythe
inside of the coee maker or block the funnel.
Please note!
If you use pre-ground coee, you can only make one cup
of coee at a time.
1. Press the button (g. 7) repeatedly until “Pre-
ground” is displayed.
2. Open the beans container lid; then open the pre-ground
coee funnel lid by pushing on PUSH and, once released,
open the lid.
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coee (g. 17).
4. Place a cup under the coee spouts.
5. Press the 1 cup coee button (g. 11).
6. Preparation begins. The amount of coee selected is dis-
played together with a progress bar which gradually lls
as preparation progresses.
Please note!
If “Energy saving” mode is enabled, you may have to wait a few
seconds before the rst coee is delivered.
MAKING DRINKS WITH MILK
Please note!
• To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water nozzle
as described in the section “Cleaning the milk container”
on pages 17.
Filling and attaching the milk container
1. Remove the lid (g. 18);
2. Fillthemilkcontainerwithasucientquantityofmilk,
not exceeding the MAX level marked on the container (g.
19). Each mark on the side of the container corresponds
to 100 ml of milk.
Please note!
• For a denser more even froth, you should use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If“energysaving”modeisenabled,youmayhavetowait
a few seconds before the rst cappuccino is delivered.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (g. 20).
4. Place the lid back on the milk container.
5. Remove the hot water spout from the nozzle, by pressing
the button.
6. Attach the container to the nozzle and push as far as it
will go (g. 21). The machine emits a beep (if the beep
function is enabled).
7. Placeasucientlylargecupunderthecoeeandfrothed
milk spouts. Adjust the length of the milk spout. To move
it nearer the cup, simply pull it downwards (g. 22).
8. Follow the instructions below for each function.
14
Adjusting the amount of froth
Turn the froth adjustment dial on the milk container lid to
adjust the amount of froth on the milk delivered while making
drinks with milk.
Dial
position
Description Recommended for…
No froth LATTE/
HOT MILK
Min. froth
FLAT WHITE
Max. froth CAPPUCCINO/ HOT MILK
(FROTHED MILK)
Making drinks with milk automatically
The CAPPUCCINO, LATTE, FLAT WHITE and HOT MILK buttons
on the control panel enable these drinks to be prepared
automatically.
Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required drink.
The name of the drink selected is displayed together
with a progress bar which gradually lls as preparation
progresses.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. For drinks with coee, the
machine automatically makes the coee after delivering
the milk.
Please note!
• If during delivery you want to stop preparation, press the
corresponding button.
• At the end of delivery, to increase the quantity of milk or
coee in the cup, just press (within 3 seconds) the button
corresponding to the drink being made.
• Donotleavethemilkcontaineroutoftherefrigeratorfor
long periods. The warmer the milk (5°C is ideal), the poor-
er the quality of froth produced.
Cleaning the milk frother with the CLEAN button
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
“SET DIAL TO CLEAN” ashes on the display each time you use
a milk function. To eliminate all milk residues, proceed as fol-
lows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Turn the froth adjustment dial to “CLEAN” (g. 22). A
progress bar appears and gradually lls as the operation
proceeds together with “Cleaning underway, Please wait”.
Cleaning stops automatically.
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
connection nozzle with a sponge.
Please note!
• Toprepareanumberofcappuccinosormilkbasedcoees,
clean the milk container after you have prepared the last
drink only.
• Themilkcontainercanbekeptintherefrigerator.
• Insomecases,tocleanyoumustwaitfortheapplianceto
heat up.
Programming the quantity of coee and milk in the
cup for the CAPPUCCINO, LATTE, FLAT WHITE and HOT
MILK buttons
The appliance is set by default to automatically deliver
standard quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coee and milk spouts.
2. Press and hold the button corresponding to the drink you
want to programme until the message “PROGRAM MILK
Program quantity” is displayed.
3. Release the button.
The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
5. The appliance stops delivering milk and after a few sec-
onds the coee is delivered into the cup. “PROGRAM COF-
FEE Program quantity” is displayed.
6. Once the required quantity of coee has been delivered
into the cup, press the button.
Coee delivery stops.
The machine is now reprogrammed with the new quantities
of milk and coee.
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water or steam.
15
The spout becomes hot during delivery. Hold by the handle
only.
Please note!
If “Energy Saving” mode is enabled, you may have to wait a few
seconds before the hot water or steam is delivered.
Delivering hot water
1. Make sure the hot water spout is attached correctly (g.
6).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the button (g. 3). “Hot water” is displayed,
together with a progress bar which lls gradually as
preparation proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically.
To interrupt delivery of hot water manually, press the
button again.
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water. To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the button again until “Hot water Program
quantity” is displayed, then release the button.
3. When the hot water in the cup reaches the required level,
press the button again.
The machine is now reprogrammed with the new quantity.
Delivering steam
1. Make sure the hot water spout is attached correctly (g.
6).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker in the liquid.
3. Press the button: after a few seconds, steam comes
out of the cappuccino maker and heats the liquid; “STE-
AM” is displayed.
4. When the required temperature is obtained, interrupt
steam delivery by pressing the button again.
(You should not discharge steam for more than 3 minutes
at a time).
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Tips for using steam to froth milk
• Whenchoosingthesizeofthecontainer,bearinmindthat
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow
movements in an upward direction.
• To avoidmilk with poor froth or large bubbles, always
clean the spout as described in the following section.
Cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and press
the button to deliver a little water (g. 3).
Stop the ow of water by pressing the button
again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout.
Hold the spout with one hand by pressing the button and
with the other, turn the cappuccino maker anticlockwise
(g. 24) and pull it downwards to remove it.
3. Also remove the steam nozzle by pulling it downwards
(g. 25).
4. Check the hole shown by the arrow in g. 25 is not
blocked. If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, turning it and pushing it upwards until it is
attached.
CLEANING
Important!
• Do not use solvents, abrasive detergents or alcohol to
clean the coee maker.
With De’Longhi bean to cup coee makers, you need not
use chemical products to clean the machine.
• Noneofthecomponentscanbewashedinadishwasher
apart from the milk container (D).
• Donotusemetalobjectstoremoveencrustationsorcof-
fee deposits as they could scratch metal or plastic surfac-
es.
Cleaning the coee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coee cannot be made.
Important! Danger of burns
16
If you make a number of cappuccinos one after the other, the
metal cup tray becomes hot.
Wait for it to cool down before touching it and handle it from
the front only.
To clean (with the machine on):
• Removethedriptray(g.26),emptyandclean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
• Checkthecondensatetray(red)andemptyifnecessary.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coees, the
grounds container may ll up more than expected and clog the
machine.
Cleaning the drip tray and condensate tray
Important!
The drip tray is tted with a level indicator (red) showing the
level of water it contains (g. 27).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned, otherwise the water may over-
ow the edge and damage the appliance, the surface it rests on
or the surrounding area.
To remove the drip tray:
1. Remove the drip tray and the grounds container (g. 26);
2. Empty the drip tray and grounds container and wash
them;
3. Check the red condensate tray and empty if necessary.
4. Replace the drip tray and grounds container.
Cleaning the inside of the coee maker
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
o (see “Turning o”) and unplugged from the mains power
supply.
Never immerse the coee maker in water.
1. Check regularly (about once a month) that the inside of
the appliance (accessible after removing the drip tray) is
not dirty. If necessary, remove coee deposits with the
brush provided or a sponge.
2. Remove the residues with a vacuum cleaner (g. 28).
Cleaning the water tank
1. Clean the water tank (A17) regularly (about once a month
and whenever you replace the water softener lter (if
provided) with a damp cloth and a little mild washing up
liquid.
2. Remove the lter (if present) and rinse with running
water.
3. Replace the lter (if provided), ll the tank with fresh wa-
ter and replace the tank.
Cleaning the coee spouts
1. Regularly clean the coee spouts with a sponge or cloth
(g. 29A).
2. Check the holes in the coee spout are not blocked. If
necessary, remove coee deposits with a toothpick (g.
29B).
Cleaning the pre-ground coee funnel
Check regularly (about once a month ) that the pre-ground
coee funnel (A6) is not blocked. If necessary, remove coee
deposits with the brush (D2) supplied.
Cleaning the infuser
The infuser (A11) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see “Turn-
ing the appliance o” on page 9).
2. Remove the water tank.
3. Open the infuser door (g. 30) on the right side.
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (g. 31).
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
6. Use the brush (D2) to remove any coee residues left in
the infuser housing, visible through the infuser door.
7. After cleaning, replace the infuser by sliding it onto the
internal support; then push the PUSH symbol fully in until
it clicks into place.
infuser support
17
Please note!
Iftheinfuserisdiculttoinsert,beforeinsertion,adaptitto
the right size by pressing the two levers shown in the gure.
7. Once inserted, make sure the two red buttons have
snapped out.
PUSH
8. Close the infuser door.
9. Replace the water tank.
Cleaning the milk container
Clean the milk container each time
you prepare milk as described
below:
1. Remove the lid.
2. Remove the milk spout and
intake tube.
3. Turn the froth adjustment
dial clockwise to the “INSERT”
position (see gure) and pull
o upwards
4. Wash all the components
thoroughly with hot water
and mild washing-up liquid.
All components are dishwash-
er safe, placing them in the
top basket of the dishwasher.
Make sure there are no milk
residues on the hollow and
groove under the dial (see
gure alongside). If neces-
sary, scrape the groove with a
toothpick.
5. Rinse inside the froth adjust-
ment dial seat with running
water (see gure)
6. Check that the intake tube
and spout are not clogged
with milk residues.
7. Replace the dial (in
correspondence to the word
“INSERT”), spout and milk
intake tube.
8. Place the lid back on the milk
container.
Cleaning the hot
water/steam nozzle
Each time you prepare
milk, clean the nozzle
with a sponge to remove
milk residues from the
gaskets (see gure
alongside).
DESCALE
Descale the machine when the message “DESCALE” ashes on
the display.
Important!
• Descaler contains acids which may irritate the skin
and eyes. It is vital to follow the manufacturer’s safety
warnings given on the descaler pack and the warnings
relating to the procedure to follow in the event of contact
with the skin and eyes.
• YoushoulduseDe’Longhidescaleronly.Usingunsuitable
descaler and/or performing descaling incorrectly may
result in faults not covered by the manufacturer’s guaran-
tee.
1. Turn the machine on.
2. Press the MENU/ESC button to enter the menu.
3. Press the HOT MILK or LATTE button until “Descale” is
displayed.
4. Select by pressing the . button: “Descale Con-
rm?” is displayed. Press again to enable the
function.
5. The message “Add descaler Conrm?” is displayed, alter-
nating with “EMPTY THE DRIP TRAY” and “REMOVE FILTER”
(if the lter is present).
6. Completely empty the water tank (A17) and remove the
water lter (if present). Empty the drip tray (g. 26) and
grounds container, then put back in the appliance.
7. Pour the descaler into the tank up to the level A (corre-
sponding to a 100 ml pack) marked on the side of the tank
(g. 32), then add water (one litre) up to level B (g. 32).
replace the water tank.
Large lever
Small lever
18
soft water ●
slightly hard water ●●
hard water ●●●
very hard water ●●●●
Set water hardness
1. Press the MENU/ESC button to enter the menu.
2. Press the HOT MILK or LATTE button to select “Water
Hardness”.
3. Conrm the selection by pressing the button.
4. Press the HOT MILK or LATTE button and set the hard-
ness shown by the indicator paper (see previous section).
5. Press the button to conrm the setting.
6. Press the MENU/ESC button to exit the menu.
The machine is now reprogrammed with the new water hard-
ness setting.
WATER FILTER
Certain models are tted with a water softener lter. If this
is not the case with your model, you are recommended to
purchase one from De’Longhi Customer Experience.
To use the lter correctly,
follow the instructions be-
low.
Installing the lter
1. Remove the lter from
the packaging.
2. Turn the date indicator
disk (see g. 33) until
the next 2 months of
use are displayed.
Please note
The lter lasts about two
months if the appliance is
used normally. If the coee
maker is left unused with
the lter installed, it will last
a maximum of three weeks.
3. To activate the lter,
run tap water through
the hole in the lter as
shown in the gure un-
til water comes out of
8. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout (g. 4).
Important! Danger of burns
Hot water containing acid ows from the spout. Avoid contact
with splashes of water.
9. Press the button to conrm that you have added
the solution.
The message “Descale underway” is displayed.
The descale programme starts and the descaler liquid
comes out of the water spout.
The descale programme automatically performs a series
of rinses and pauses to remove limescale deposits from
inside the machine.
After about 30 minutes, the message “Rinsing” “INSERT FILTER”
(if present), “FILL TANK” is displayed.
10. The appliance is now ready for rinsing through with clean
water. Extract the water tank, empty, rinse under running
water, ll with clean water up to the MAX level, insert the
lter (if removed previously) and put the water tank back
in the machine. “Rinsing Conrm?” is displayed.
11. Empty the container used to collect the descaler solution
and replace it empty under the cappuccino maker.
12. Press the button to start rinsing. Hot water ows
out of the spout and the message “Rinsing Please wait” is
displayed.
13. When the water tank is completely empty, the message
“Rinsing complete Conrm?” is displayed.
14. Press the button.
15. “Heating up Please wait” is displayed, at the end of which
the machine will be ready for use.
SETTING WATER HARDNESS
The DESCALE message is displayed after a period of time
according to water hardness.
The machine is factory set for a hardness value of 4.
The machine can also be programmed according to the hard-
ness of the mains water in the various regions so that the ma-
chine needs to be descaled less often.
Measuring water hardness
1. Remove the “total hardness test” indicator paper attached
to this manual from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly.
After about a minute, 1, 2, 3, or 4 red squares form, de-
pending on the hardness of the water. each square corre-
sponds to one level.
33
35
36A
36B
34
19
the openings at the side
for more than a minute
(g. 34).
4. Extract the tank from the
appliance and ll with
water.
5. Insert the lter in the
water tank and immerse
it completely for about
ten minutes, sloping it to
enable the air bubbles to
escape (g. 35).
6. Insert the lter in the l-
ter housing and press as
far as it will go (g. 36A)
7. Close the tank with the
lid, then put the tank
back in the machine (g.
36B).
When you install the lter,
you must notify the appliance
of its presence.
8. Press the MENU/ESC button to enter the menu;
8. Press the HOT MILK or LATTE button (g. 8) until “Install
lter” is displayed;
10. Press the button;
11. The message “Enable?” is displayed.
12. Press the button to conrm the selection. “Hot
water Conrm?” is displayed;
13. Position a container under the hot water spout (min. ca-
pacity: 500 ml);
14. Press the button to conrm the selection. The
appliance begins hot water delivery and the message
“Please wait” is displayed;
15. After delivery, the appliance returns automatically to the
“Ready for coee” position.
The new lter is active. You can now use the coee maker.
Replacing the lter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or when the appliance has not been used for 3
weeks, you should replace the lter:
1. Extract the tank and exhausted lter;
2. Take the new lter out of its packet and proceed as
illustrated in points 2, 3, 4, 5 and 6 in the previous section.
3. Position a container with a minimum capacity of 500 ml
under the hot water spout.
4. Press the MENU/ESC button to enter the menu;
5. Press the HOT MILK or LATTE button until “Replace lter
“ is displayed.
6. Press the button;
7. The message “Conrm?” is displayed.
8. Press the button to conrm the selection;
9. “Hot water… Conrm?” is displayed.
10. Press the button to conrm the selection. the
appliance begins delivering hot water and the message
“Please wait “ is displayed.
11. After delivery, the appliance returns automatically to the
“ready for coee” position.
The new lter is now active and you can use the coee maker.
Removing the lter
If you want to continue using the appliance without a lter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted lter;
2. Press the MENU/ESC button to enter the menu;
3. Press the HOT MILK or LATTE button (g. 8) until “Install
lter Enabled” is displayed;
4. Press the button
5. “Disable?” is displayed;
6. Press the button to conrm and the MENU/ESC
button to exit the menu.
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 15 bar
Water tank capacity: 2.0 litres max.
Size Lxhxd: 238x350x445 mm
Cable length: 1.80 m
Weight: 11.8 kg
Beans container capacity: 250 g max.
The appliance complies with the following EC
directives:
• ECRegulation1275/2008forstandby;
• Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMCdirective2004/108/ECandsubsequentamendments
• Materialsandaccessoriescomingintocontactwithfood
conform to eec regulation 1935/2004.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with hou-
sehold waste, but taken to an authorised waste se-
paration and recycling centre.
33
35
36A
36B
20
DISPLAYED MESSAGES
DISPLAYED MESSAGE POSSIBLE CAUSE SOLUTION
FILL TANK Insucientwaterinthetank. Fill the tank with water and/or insert it
correctly, pushing it as far as it will go until it
clicks into place.
EMPTY GROUNDS CONTAINER The grounds container (A22) is full.
Empty the grounds container and drip tray,
clean and replace. Important: when removing
the drip tray, the grounds container must be
emptied, even if it is not completely full.
If this is not done, when you make the next
coees, the grounds container may ll up more
than expected and clog the machine.
GROUND TOO FINE ADJUST
MILL
The grinding is too ne and the coee is
delivered too slowly or not at all.
The grinding is too ne and the coee is
delivered too slowly or not at all.
Repeat coee delivery and turn the grinding
adjustment dial (g. 10) one click clockwise to-
wards “7” while the coee mill is in operation.
If after making at least 2 coees delivery is
still too slow, repeat the correction procedure,
turning the grinding adjustment dial another
click until delivery is correct (see the section:
“Adjusting the coee mill” on page 12). If the
problem persists, make sure the water tank is
fully inserted, press the button and
deliver a little water from the spout.
INSERT GROUNDS CONTAINER After cleaning, the grounds container has not
been replaced.
Remove the drip tray and insert the grounds
container.
ADD PRE-GROUND COFFEE With the pre-ground function selected,
pre-ground coee has not been poured into
the funnel.
Place pre-ground coee in the funnel or
deselect the “pre-ground” function (g. 17).
DESCALE The machine must be descaled. The descaling procedure described in the
section “Descaling” needs to be performed as
soon as possible (page 17).
LESS COFFEE Too much coee has been used.
Select a milder taste by pressing the dial
(g. 9) or reduce the quantity of pre-ground
coee.
FILL BEANS CONTAINER The coee beans have run out. Fill the beans container (g. 13).
The pre-ground coee funnel is clogged. Empty the funnel with the help of a brush as
described in the section “Cleaning the pre-
ground coee funnel”.
INSERT INFUSER ASSEMBLY The infuser has not been replaced after
cleaning.
Insert the infuser as described in the
paragraph “Cleaning the infuser”.
INSERT TANK The tank is not correctly in place. Insert the tank correctly and press as far as it
will go.
21
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM POSSIBLE CAUSE SOLUTION
The coee is not hot The cups were not preheated. • Enablethecupwarmer,leavethecupsat
least 20 minutes to warm up.
• Warm the cups by rinsing them with hot
water (N.B. you can use the hot water
function).
The infuser has cooled down because
2/3 minutes have elapsed since the last
coee was made.
Before making the coee, warm the infuser by
using the Rinsing function to perform a rinse
cycle (page 10).
Low coee temperature is set. In the menu, set a higher coee temperature.
The coee is thin or not creamy
enough.
The coee is ground too coarsely. Turn the grinding adjustment dial one click an-
ticlockwise towards “1” while the coee mill is
in operation (g. 12).
Continue one click at a time until coee delive-
ry is satisfactory. The eect is only visible after
delivering 2 coees (see the section: “adjusting
the coee mill” on page 12).
The coee is unsuitable. Use pre-ground coee for espresso coee ma-
kers
The coee is delivered too slowly or a
drop at a time.
The coee is ground too nely. Turn the grinding adjustment dial one click
clockwise towards “7” while the coee mill is
in operation (g. 12).
Continue one click at a time until coee delive-
ry is satisfactory. The eect is only visible after
delivering two coees. (see the section “adju-
sting the coee mill” on page 12).
GENERAL ALARM The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,
as described in the section “Cleaning and
maintenance”. If the message is still displayed
after cleaning, contact a service centre.
EMPTY CIRCUIT FILL CIRCUIT
alternating with
Hot water press OK
The water circuit is empty. Press OK to deliver water from the spout (A14)
until it ows out normally.
REPLACE FILTER The water lter is exhausted. Replace the lter or remove it as described in
the section “Water lter”.
SET DIAL TO CLEAN Milk has been delivered recently and the tubes
inside the milk container must be cleaned.
Turn the froth adjustment dial to CLEAN.
INSERT WATER SPOUT The hot water spout is not inserted or is
inserted incorrectly.
Insert the water spout (D3) as far as it will go.
INSERT MILK CONTAINER The milk container is not inserted correctly. Insert the milk container (g. 21) as far as it
will go.
22
Coee does not come out of one of
the spouts.
The spouts are blocked. Clean the spouts with a toothpick (g. 29B).
The milk does not
come out of the milk
spout.
The milk container lid is dirty. Clean the milk container lid as described in
the section “Cleaning the milk container”.
The milk contains
large bubbles and
squirts out of the
milk spout or there
is little froth .
the milk container lid is dirty. Clean the milk container lid as described in the
section “cleaning the milk container”.
the milk is not cold enough or is not
semi-skimmed.
Use skimmed or semi-skimmed milk at refrige-
rator temperature (about 5° c).
If the result is not as you wished, try changing
brand of milk.
The froth adjustment dial is incorrectly
adjusted.
Adjust following the instructions in the section
“making drinks with milk”.
The milk container lid or froth
adjustment dial is dirty
Clean the milk container lid and dial as de-
scribed in the section “cleaning the milk con-
tainer”.
The milk contains
large bubbles there
is little froth .
The hot water/steam nozzle is dirty Clean the nozzle as described in the section
“cleaning the hot water/steam nozzle”.
The appliance does not come on. The spout is dirty. Clean as described in the section “Cleaning the
spout after use”.
It is not plugged into the mains socket. Plug into the mains socket.
The main switch (A7) is not turned on. Place the main switch in the i position (g. 2).
The infuser cannot be extracted The appliance has not been turned o
correctly
Turn the appliance o by pressing the but-
ton (pag. 9).
23
ELECTRICAL CONNECTION UK ONLY
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The exible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not t the socket outlets in your home, it should be cut o and replaced with a suitable plug, following the proce-
dure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might nd it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched o when the machine is not in
use.
IMPORTANT: The wires in the mains lead tted to this appliance are coloured in accordance with the following code:
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWN LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualied
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualied electrician and should
only be replaced with a exible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be retted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be tted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
Green and Yellow to Earth
13 amp Fuse
Brown to live
Cord Clamp
Blue to
neutral
