Loading ...
Loading ...
Loading ...
15
The spout becomes hot during delivery. Hold by the handle
only.
Please note!
If “Energy Saving” mode is enabled, you may have to wait a few
seconds before the hot water or steam is delivered.
Delivering hot water
1. Make sure the hot water spout is attached correctly (g.
6).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the button (g. 3). “Hot water” is displayed,
together with a progress bar which lls gradually as
preparation proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically.
To interrupt delivery of hot water manually, press the
button again.
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water. To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the button again until “Hot water Program
quantity” is displayed, then release the button.
3. When the hot water in the cup reaches the required level,
press the button again.
The machine is now reprogrammed with the new quantity.
Delivering steam
1. Make sure the hot water spout is attached correctly (g.
6).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker in the liquid.
3. Press the button: after a few seconds, steam comes
out of the cappuccino maker and heats the liquid; “STE-
AM” is displayed.
4. When the required temperature is obtained, interrupt
steam delivery by pressing the button again.
(You should not discharge steam for more than 3 minutes
at a time).
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Tips for using steam to froth milk
• Whenchoosingthesizeofthecontainer,bearinmindthat
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow
movements in an upward direction.
• To avoidmilk with poor froth or large bubbles, always
clean the spout as described in the following section.
Cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and press
the button to deliver a little water (g. 3).
Stop the ow of water by pressing the button
again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout.
Hold the spout with one hand by pressing the button and
with the other, turn the cappuccino maker anticlockwise
(g. 24) and pull it downwards to remove it.
3. Also remove the steam nozzle by pulling it downwards
(g. 25).
4. Check the hole shown by the arrow in g. 25 is not
blocked. If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, turning it and pushing it upwards until it is
attached.
CLEANING
Important!
• Do not use solvents, abrasive detergents or alcohol to
clean the coee maker.
With De’Longhi bean to cup coee makers, you need not
use chemical products to clean the machine.
• Noneofthecomponentscanbewashedinadishwasher
apart from the milk container (D).
• Donotusemetalobjectstoremoveencrustationsorcof-
fee deposits as they could scratch metal or plastic surfac-
es.
Cleaning the coee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coee cannot be made.
Important! Danger of burns
Loading ...
Loading ...
Loading ...