Loading ...
Loading ...
Loading ...
27
SETTING OVEN CONTROLS
SETTINGPROBE(Upperovenonly)
Tosettheoventoautomaticallystopcookingandstart
keepwarmoncereachingtargettemperature:
1. Press PROBE and hold for 6 seconds.
2. Press SELF CLEAN and toggle until CAnCEL appears
then press START to accept.
TosetProbe:
1. Insert the probe into the food. Place prepared food on
the desired oven rack position and slide into the oven.
2. Plug the connector end of the probe all the way into the
probe receptacle while the oven is cool. The receptacle
is located on the upper left front oven cavity wall. On
some models the receptacle is located on the top of the
oven cavity near the front.
3. When the probe is set, an acceptance tone will sound, the
probe icon will illuminate and the actual probe temperature
appears in the display. Close the oven door.
4. Press PROBE once. Enter the desired target food
temperature using the numeric keys and set temperature
for food type. The minimum setting is 140ºF/ 60ºC; the
maximum is 210ºF/99ºC. Default is 170ºF/77ºC.
5. Press START to accept the target temperature.
6. Set for BAKE, CONVECTIONBAKE or CONVECTION
ROAST and if necessary adjust the oven temperature
accordingly.
7. The control will provide 3 beeps when the internal target
temperature is reached. The oven will automatically
change to a keep warm setting (HLd and the actual
probe temperature will alternate in the display). Warm
will maintain the oven temperature at 170° F(77°C) for
3 hours unless otherwise cancelled.
8. To stop cooking at any time press OFF.
Probeerrormessage:
If the error message Prob ERR displays, check to be sure
that the probe connector is fully inserted into the receptacle.
If the probe is fully inserted and the error message continues,
the probe may be defective and need to be replaced. When
Prob ERR displays, the oven control will not permit any oven
feature to activate until corrected or the probe is removed.
If the error message continues, remove the probe from the
receptacle and oven.
Probetoohotmessage:
When the message Prob... Too... Hot... ashes in the
display, the probe temperature has exceeded 250°F (121°C).
If the probe is not removed this message may continue
until the sensor reaches 300°F (149°C) or higher, at which
time the oven will automatically turn off and display Prob
ERR message. This message may be generated if the probe
sensor is exposed to direct oven heat or the food internal
temperature is over 250°F (121°C). Be sure the probe sensor
is fully covered by the food or if the food is done, press OFF
and remove food and probe from the oven.
+ The U.S. Department of Agriculture states, “Rare fresh
beefispopular,butyoushouldknowthatcooking
ittoonly140°F/60°Cmeanssomefoodpoisoning
organismsmaysurvive.” (Source: Safe Food Book, Your
Kitchen Guide, USDA Rev. June 1985.)
Visit the USDA Food Safety and Inspection website at
www.fsis.usda.gov
FoodType InternalTemp.
Ground meat & meat mixtures
Beef, Pork, Veal, Lamb 160°F (71°C)
Turkey, Chicken 165°F (74°C)
Freshbeef,veal,lamb
Medium rare + 145°F (63°C)
Medium 160°F (71°C)
Well Done 170°F (77°C)
Poultry
Chicken & Turkey, whole 165°F (74°C)
Poultry Breasts, Roasts 165°F (74°C)
Poultry Thighs, Wings 165°F (74°C)
Duck & Goose 165°F (74°C)
Stufng (cooked alone or in bird) 165°F (74°C)
Fresh Pork 160°F (71°C)
Ham
Fresh (raw) 160°F (71°C)
Pre-cooked (to reheat) 140°F (60°C
Eggs & egg dishes
Eggs Cook until yolk and
white are rm
Eggs dishes 160°F (71°C)
Leftovers & Casseroles 165°F (74°C)
NOTE
During cooking the internal food temperature will display
by default. To review the target temperature press the
probe key once. After 6 seconds the display will revert
to the internal food temperature. To assure accuracy, do
not remove the probe from the food or receptacle until
the desired internal temperature is reached.
If the probe is active and the probe is removed from the
receptacle only, the probe feature will cancel but the oven
will continue to cook. If the probe is removed from the
food only, the probe feature will remain active, and may
eventually generate a Probe Too Hot message.
To change the target temperature while cooking, press
the probe key once. Use the numeric keys to change the
target temperature. Press the start key to accept any
change. The probe feature can not be used with broil or
self clean.
Loading ...
Loading ...
Loading ...