Loading ...
Loading ...
Loading ...
11
Rinsing
Use this function to deliver hot water from the coee spout (A8)
and from the hot water spout (C3), if inserted, to clean and heat
the appliance’s internal circuit. Place a container with a mini-
mum capacity of 100ml under the coee and hot water spout.
To enable the function, proceed as follows:
1. Press the
icon (B2) to enter the menu;
2. Press
or (g. 5) until “Rinsing” is displayed;
3.
Press the icon (g.6), “Conrm?” is displayed;
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. Press the
icon: after a few seconds, hot water is deliv-
ered rst from the coee spout and then from the hot water
spout (if inserted) which cleans and heats the appliance’s
internal circuit.
Please note!
• To stop delivery at any time, press any icon.
• If the appliance is not used for more than 3-4 days, we strong-
ly recommend, when switching on the appliance, performing
2/3 rinses before using it.
Descaling
For instructions on descaling, see page 18.
Install lter
For Instruction for use on how to install the lter, see the section
“Water softener lter” (page 20).
Replacing the limescale lter (if installed)
For Instruction for use on how to replace the lter, see the sec-
tion “Replacing the lter” (page 20).
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the
icon (B2) to enter the menu;
2. Press
or (g. 5) until “Adjust time” is displayed;
3. Press the
icon (g. 3). The hours ash on the display;
4. Press
or to change the hour;
5. Press the
icon to conrm. The minutes ash;
6. Press or to change the minutes;
7. Press the
icon to conrm.
This sets the time. Press the
icon to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the
icon (B2) to enter the menu;
2. Press
or (g. 5) until “Auto-start” is displayed;
3. Press the
button (g. 3). “Enable?” is displayed;
4. Press the icon to conrm;
5.
Press
or
to choose the hour;
6. Press the
icon to conrm;
7. Press or to change the minutes;
8. Press the
icon to conrm;
9. Press the
icon to exit the menu.
Once the time has been conrmed, activation of auto-start is
indicated by the
symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the
icon. “Disable?” is displayed;
3. Press the icon to conrm.
The
symbol is no longer displayed.
Auto-o (standby)
Auto-o can be set so that the appliance goes o after 15 or
30 minutes, or 1, 2 or 3 hours. To programme Auto-o, proceed
as follows:
1. Press the
(B2) icon (B2) to enter the menu;
2. Press
or (g. 5) until “Auto-o” is displayed;
3. Press the
icon (g. 6);
4. Press
or until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the
icon to conrm;
6. Press the
icon to exit the menu.
Auto-o is programmed.
Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the
icon (B2) to enter the menu;
2. Press
or (g. 5) until “Energy Saving” is
displayed;
Loading ...
Loading ...
Loading ...