Loading ...
Loading ...
Loading ...
33
/3&RQYHUVLRQ,QVWUXFWLRQV
$'-8677+(/2:)/$0(6,00(5
6(77,1*
The top burner valves have low flame/simmer
adjustment screws, accessible through the
valve switches. A small, thin-blade screwdriver
(approximately 1/8” blade width) is needed to access
the screw.
A
Light two other burners and set the knobs to a
medium to high setting.
B
Light the burner to be adjusted and turn the knob to
/2 or 6,00(5
C
To make adjustment, remove the control knobs. Insert
a screwdriver through the access hole in the valve
switch. Engage the adjustment screw in the valve.
If the flames were too
small or fluttered, open
the valve more than the
original setting.
If the flames are too large,
close the valve more than
the original setting.
D
Make the adjustment by
slowly turning the screw
until the flame appearance is correct. For the left side,
install the grill burner for the adjustment. The left side
cannot be turned down as low as the right side if the
grill burner is to be used.
$GMXVWWKHORZIODPHVHWWLQJXVLQJWKHYDOYHE\SDVV
VFUHZDVIROORZV
Low setting adjustments must be made with two other
burners in operation on a medium setting. This prevents
the low flame from being set too low, resulting in the
flame being extinguished when other burners are turned
on.
E
7HVWLQJ)ODPH6WDELOLW\
Test 1: Turn the knob from+,to /2 or 6,00(5
quickly. If the /2 or 6,00(5 flame goes out,
increase the flame size and test again.
Test 2: With the burner on the /2 or 6,00(5 setting,
open and close the cabinet door under the
cooktop. If the flame is extinguished by the
air currents created by the door movement,
increase the flame height and test again.
Test 3: With the burner on the /2 or 6,00(5 setting,
turn the downdraft vent fan to the +, position.
If the flame is extinguished by the air currents
created by the downdraft vent fan, increase
the flame size and test again.
5
&219(57,1*%$&.721$785$/*$6
To convert the cooktop back to natural gas, reverse the
steps taken to convert to LP.
Once the conversion is complete and checked OK, fill
out the LP sticker and include your name, organization
and date conversion was made. Apply the sticker near
the cooktop gas inlet opening to alert others in the
future that this appliance has been converted to LP
gas. If converting back to natural gas from LP, please
remove the sticker so others know the appliance is set
to use natural gas.
127( For operation at elevations above 5000 ft. (1500
m), equipment ratings shall be reduced at a rate of
2% for each 1000 ft. (300 m) above sea level before
selecting appropriately sized equipment, i.e.: Use
smaller orifices.
1DWXUDO*DVµ:&3
%XUQHU2XWSXW5DWLQJLQ%78+5
/RFDWLRQ %78V 2ULILFH6L]H (QJUDYLQJ
Left Rear (LR) 10,000 .0550 NAT
Left Front (LF) 10,000 .0550 NAT
Right Rear (RR) 10,000 .0550 NAT
Right Front (RF) 10,000 .0550 NAT
$'-8677+(/2:)/$0(6,00(5
6(77,1*
FRQW
)
)ODPH5HFKHFN
Repeat the adjustment for each burner. After the
adjustment is made, turn all burners off. Ignite
each burner individually. Observe the flame at the
+,position. Rotate the valve to the /2 or 6,00(5
position and be sure that the flame size decreases
as the valve is rotated counterclockwise.
5
6
Loading ...
Loading ...
Loading ...