Loading ...
Loading ...
Loading ...
16
EMC INFORMATION
This medical device complies to the IEC 60601-1-2:2007 standard for Electromagnetic Compatibility.
See tables 1, 2, 4 and 6 for compliance details.
Table 1 - Guidance and Manufacturer’s Declaration - Electromagnetic Emissions
The
SLENDERTONE COREFIT is intended for use in the electromagnetic environment specified below. The customer or the user
of the
SLENDERTONE COREFIT should ensure that it is used in such an environment.
Emissions Test Compliance Electromagnetic Environment - Guidance
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Group 2
Class B
Not applicable
Complies
The
SLENDERTONE COREFIT must emit electromagnetic energy in order to perform its
intended function.
The
SLENDERTONE COREFIT is suitable for use in all establishments, including domestic
and those directly connected to the public low-voltage power supply network that
supplies buildings used for domestic purposes.
Table 6 - Recommended separation distances between portable and mobile RF communication
equipment and the
SLENDERTONE COREFIT.
The
SLENDERTONE COREFIT is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of the
SLENDERTONE COREFIT can help prevent electromagnetic interference by maintaining
a minimum distance between portable and mobile RF communications equipment (transmitters) and the
SLENDERTONE
COREFIT as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter (W)
Separation distance according to frequency of transmitter (m)
150 KHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz
0.01
0.1
1
10
100
d = 1.17 P
0.12
0.37
1.17
3.70
11.70
d = 1.17 P
0.12
0.37
1.17
3.70
11.70
d = 2.33 P
0.23
0.75
2.33
7.36
23.50
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m)
can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power
rating of the transmitter in watts (w) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: Changes / modifications not approved by the manufacturer could void the user’s authority to operate the equipment.
N
OTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Loading ...
Loading ...
Loading ...