7
INSTALLATION
UNPACKING AND CLEANING
Remove all packaging and securing tapes from the appliance.
+ƫ2+% ƫ%*&1.5ƫ* ƫ1/%*#ƫ )#!ƫ0+ƫ0$!ƫ,,(%*!Čƫ!ƫ!40.!)!(5ƫ
cautious when using sharp or pointed tools to complete this task.
Keep children away from the packaging material - DANGER OF SUF-
FOCATION! Wash the inside and outside of the appliance with luke
warm water and a mild soap or detergent. Abrasive or corrosive
cleaning agents, steel wool, scouring sponges, or chemical cleaning
agents should not be used under any circumstances. A sponge, soft
brush or towel is recommended. After cleaning, thoroughly rinse and
dry. You may want to leave the doors open allowing the compart-
ments to ventilate for 20-30 minutes to get rid of residual odors.
Check with your local Environmental Agency for recommendations
on recycling packaging materials in your area.
POSITIONING THE APPLIANCE
The area in which the fridge is to be installed must be relatively cool,
dry, and suitably ventilated. The area must be protected against any
%*(!)!*0ƫ3!0$!.ƫĨ.%*Čƫ/*+3ĩƫ* ƫ!4!//%2!ƫ/1."!ƫ 1/0ċƫƫ+ƫ!*/1.!ƫ
,.+,!.ƫ"1*0%+*Čƫ0$!ƫ,,(%*!ƫ)1/0ƫ!ƫ,(! ƫ+*ƫƫý0Čƫü.)Čƫ* ƫ
/0(!ƫ/1."!ƫ.!/0%*#ƫ(!2!(ƫ+*ƫ((ƫ"+1.ƫ/1,,+.0/ċƫ$!ƫý++.ƫ)1/0ƫ!ƫ
strong enough to support a fully loaded cabinet. Use wood or metal
shims to level the fridge if necessary.
+ƫ*+0ƫ,(!ƫ0$!ƫ".% #!ƫ(+/!ƫ0+ƫ$!0ƫ/+1.!/ƫĨ$!0!.Čƫ/0+2!Čƫ+%(!.Čƫ
$%)*!5Čƫ!0ċĩČƫ* ƫ2+% ƫ,.+(+*#! ƫ!4,+/1.!ƫ0+ƫ %.!0ƫ/1*(%#$0ċƫƫ$%/ƫ
,,(%*!ƫ1/!/ƫ0$!ƫ!40!.%+.ƫ3((/ƫ0+ƫ0.*/"!.ƫ$!0ƫ".+)ƫ0$!ƫ%*/% !ƫ+"ƫ
the cabinet. Ensure that there is adequate space between the fridge
* ƫ*!%#$+.%*#ƫ3((/ƫ+.ƫ(.#!ƫ+&!0/ċƫƫƫ)%*%)1)ƫ/,%*#ƫ+"ƫăƫ
%*$!/ƫĨĈċĆƫ)ĩƫ%/ƫ$%#$(5ƫ.!+))!* ! ċƫƫ$%/ƫ3%((ƫ,.+2% !ƫ/1þ%!*0ƫ
%.ý+3ƫ.+1* ƫ0$!ƫ,,(%*!ƫ.!/1(0%*#ƫ%*ƫ)+.!ƫ!þ%!*0ƫ+,!.0%+*ƫ* ƫ
longer appliance lifetime. Always keep the air vent openings of the
compressor housing cover free from dust and obstructions.
8
The default left side orientation of the door can be changed to the
right side. Use the following procedure to change the side of the
door hinge.
Tools required: Slot screwdriver, Cross screwdriver, Spanner
1. Set the thermostat to the 0 position and disconnect the power
plug from the electrical outlet.
Ăċƫ%(0ƫ0$!ƫ,,(%*!ƫ'3. /ƫ0+ƫ*ƫ*#(!ƫ+"ƫąĆŋƫ* ƫ/!1.!(5ƫ/1,
port it.
3. Remove the shelves, crisper and egg tray from the unit.
ąċƫ!)+2!ƫ0$!ƫĂƫ/0+,,!./ƫ3%0$ƫƫ/.!3 .%2!.ƫĨý0ƫ/.!3 .%2!.ĩċ
PARTS LIST
PARTS LIST
1: Shelf
2: Freezer compartment
3: Bulb with cover
4: Thermostat 0 - 7
Ćčƫ++.
6: Upper hinge
7: Lower hinge
ĉčƫ &1/0(!ƫ"!!0
9: Crisper
10: Detachable door rack
11: Middle hinge
12: Egg Tray
13: Power Cable
āąčƫĥƫ(1#ƫĨ+,0%+*(ƫƫƫ
ƫƫƫƫƫ"+.ƫ+*ġ#.% ƫ1/!ĩ
12
13
DOOR REMOVAL AND REVERSAL
AC/DC plug
Ĩ+,0%+*(ƫ"+.ƫ+*ġ#.% ƫ1/!ĩƫ
*sold separately
14
9
Ćċƫ*/.!3ƫ0$!ƫ &1/0(!ƫ"!!0ƫĨĉĩƫ+*ƫ0$!ƫ+00+)ċ
ćċƫ*/.!3ƫ0$!ƫ(+3!.ƫ$%*#!ƫĨĈĩċ
Ĉċƫ!)+2!ƫ0$!ƫ ++.ƫĨĆĩċ
8. Unscrew the middle hinge.
9. Remove the freezer door.
āĀċƫ*/.!3ƫ0$!ƫ$%*#!ƫ,%*ƫ".+)ƫ1,,!.ƫ$%*#!ƫĨćĩƫ* ƫ/.!3ƫ%0ƫ0+ƫ0$!ƫƫ
other side of the fridge.
āāċƫ*/.!3ƫ0$!ƫ$%*#!ƫ/0+,,!./ƫĨ%*(1 %*#ƫ$%*#!ƫ,%*ĩƫ".+)ƫ0$!ƫ
freezer door and fridge door and place them on the other side.
12. Check now if all the hinges and shafts are moved to same side
13. Attach the freezer door to the upper hinge.
14. Attach the middle hinge to the freezer door and screw them
together.
āĆċƫ00$! ƫ0$!ƫ".% #!ƫ ++.ƫĨĆĩƫ0+ƫ0$!ƫ)% (!ƫ$%*#!ċ
āćċƫ00$ƫ0$!ƫ(+3!.ƫ$%*#!ƫĨĈĩƫ0+ƫ0$!ƫ ++.ƫ* ƫ/.!3ƫ0$!)ƫ0+#!0$!.ċ
17. Cover the middle hinge holes with 2 stoppers.
18. Put glass shelves, crisper and egg tray to their original position.
19. Make sure that the door is in the vertical position and can be
closed easily.
IMPORTANT: After reversing the door hinge, the door gasket may
be loose. Should you notice a gap between the gasket and the
cabinet, use a hairdryer or heat gun and heat the gasket while on
0$!ƫ,,(%*!ċƫ$!ƫ#/'!0ƫ3%((ƫ!4,* ƫ0+ƫ)!!0ƫ0$!ƫ%*!0ċƫ((+3ƫăĀƫ
mins to cool before opening. A correct gasket positioning is the key
to prevent refrigerated air from escaping.
DOOR REMOVAL AND REVERSAL continued
10
ELECTRICAL DIAGRAM
+ to + and - to -
positive to positive / negative to negative
(red wire) / (black wire)
THIS FRIDGE MUST NEVER BE CONNECTED DIRECTLY
TO ANY AC (alternating current) POWER SOURCE!
THE FRIDGE MUST ONLY BE CONNECTED TO A 12V OR 24V DC
POWER SOURCE, SUCH AS A SOLAR
BATTERY SYSTEM OR CHARGE CONTROLLER.
THE FRIDGE WILL AUTOMATICALLY OPERATE ON EITHER 12V OR
24V DC. THE USER DOES NOT NEED TO MAKE ANY ADJUSTMENT.
ATTENTION: Polarity is important in wiring this DC appliance. Be
sure that the positive terminal of the battery or charge controller
coincides with the positive wire to the compressor, and the nega-
tive terminal of the battery or charge controller coincides with the
negative wire to the compressor. The leads should be connected
using cable shoes and screwed connections. Joined leads should be
avoided.
DC POWER CONNECTION
UGP-260L1 Wiring Diagram
UGP-260L1 Schéma de Câblage
UGP-260L1 Wiring Diagram Label
1: Input power 12VDC /24VDC
2: Fuse 15 A
3: Main PCBA cooling unit
4: Interior light
5: Thermostat
6: LED Error light
7: R1(Speed selection)
1: La puissance d’entrée
12VDC/24VDC
2: Fusible 15A
3: Unité principale de refroid-
issement PCBA
4: Lumiére d’intérieur
5: Thermostat
6: LED (lumiére error)
7: R1 (sélection de vitesse)
WHITE
RED
BROWN
BLACK
YE/GN
P
F+
R E S IS TA N C E
LED errors Light/lumiere errors
Interior Light
1
2
3
5
6
7
BLANC
ROUGE
RED
ROUGE
MARRON
NOIR
BLACK
NOIR
BLACK
NOIR
BLACK
NOIR
BLACK
NOIR
Lumiere Interior
4
JAUNE/VERT
FUSE
FUSIBLE
BLACK
NOIR
RED
ROUGE
6”
4”
UGP-260L1 Wiring Diagram
UGP-260L1 Schéma de Câblage
UGP-260L1 Wiring Diagram Label
1: Input power 12VDC /24VDC
2: Fuse 15 A
3: Main PCBA cooling unit
4: Interior light
5: Thermostat
6: LED Error light
7: R1(Speed selection)
1: La puissance d’entrée
12VDC/24VDC
2: Fusible 15A
3: Unité principale de refroid-
issement PCBA
4: Lumiére d’intérieur
5: Thermostat
6: LED (lumiére error)
7: R1 (sélection de vitesse)
WHITE
RED
BROWN
BLACK
YE/GN
P
F+
R E S I S TA N C E
LED errors Light/lumiere errors
Interior Light
1
2
3
5
6
7
BLANC
ROUGE
RED
ROUGE
MARRON
NOIR
BLACK
NOIR
BLACK
NOIR
BLACK
NOIR
BLACK
NOIR
Lumiere Interior
4
JAUNE/VERT
FUSE
FUSIBLE
BLACK
NOIR
RED
ROUGE
6”
4”
11
IN-LINE FUSE
ƫāĆƫ%*ġ(%*!ƫ"1/!ƫ%/ƫ,.+2% ! ƫ3%0$ƫ0$%/ƫ".% #!ƫ%*ƫ+. !.ƫ0+ƫ,.+0!0ƫ0$!ƫ
wiring. For 12V operation, use a 15A fuse. A standard automobile
fuse is recommended and the fuse should be wired to the positive
ĨėŐĘĩƫ/% !ƫ+"ƫ0$!ƫ/5/0!)ƫ(+/!ƫ0+ƫ0$!ƫ,+/%0%2!ƫ00!.5ƫ0!.)%*(ċƫ
A 15A fuse is provided with this fridge/freezer.
OPERATING VOLTAGE FUSE
12 V / 24 V āĆƫ
DC POWER CONNECTION continued
ATTENTION
If a longer connection cable is necessary, the cable cross section
Ĩ+.ƫ#1#!ĩƫ)1/0ƫ!ƫ!-1(ƫ0+ƫ+.ƫ#.!0!.ƫ0$*ƫ0$!ƫ(!ƫ/%6!/ƫ.!+)-
mended on the following table. Be careful that the input voltage at
the appliance does not drop below the cut-out voltage of the com-
pressor.
CABLE SIZE 12V CABLE
LENGTH
24V CABLE
LENGTH
AREA AWG
mm
2
/inch Gauge m ft m ft
2.5 /
3
/
32
”
12 2.5 8 5 16
4 /
5
/
32
”
12 4 13 8 26
6 /
15
/
64
”
10 6 19.5 12 39
10 /
25
/
64
”
8 10 32.8 20 65.6
LOW VOLTAGE DISCONNECT
The compressor electronics includes a low voltage disconnect fea-
01.!ċƫƫ"ƫ0$!ƫ%*,10ƫ2+(0#!ƫ0+ƫ0$!ƫ,,(%*!ƫ"((/ƫ!(+3ƫāĀċąƫĨ%*ƫāĂƫƫ
)+ !ĩƫ+.ƫĂĂċĉƫĨ%*ƫĂąƫƫ)+ !ĩČƫ0$!ƫ+),.!//+.ƫ3%((ƫ/$10ġ+ûċƫƫ*!ƫ
0$!ƫ2+(0#!ƫ%*.!/!/ƫ+2!ƫāāċĈƫĨ%*ƫāĂƫ)+ !ĩƫ+.ƫĂąċĂƫĨ%*ƫĂąƫ
)+ !ĩČƫ0$!ƫ+),.!//+.ƫ3%((ƫ.!/1)!ƫ*+.)(ƫ+,!.0%+*ċƫƫ
$%/ƫ"!01.!ƫ%/ƫ !/%#*! ƫ0+ƫ,.+0!0ƫ0$!ƫ/5/0!)ƫ00!.5ƫ".+)ƫ!4,!.%-
encing too low a depth of discharge.
12 V OPERATION 24 V OPERATION
SHUT-OFF 10.4 V 22.8 V
RESTART 11.7 V 24.2 V
