Loading ...
Loading ...
Loading ...
26
Setup, con’t
RoomPerfect, con’t
The MEN220 will automatically assign the next
available focus position number to the just completed
measurement. If you would like to assign a different
focus position number rotate the ADJUST Control to
select a different number.
16. Press the SELECT Push-button to save the Focus
Position and “Calculating Filters, Please wait”.
Refer to figure 84 on page 25.
If you would like to add additional Focus Positions at
this time repeat steps 11 thru 16 . The MEN220 will
exit the RoomPerfect Setup Mode in several minutes.
To exit sooner press the MENU Push-button until the
Front Panel Display indicates the Focus 2 (or higher) is
active.
ADDITIONAL MEASUREMENTS:
The MEN220 allows for additional room measure-
ments to be added to the initial RoomPerfect measure-
ments. These additional measurements will increase
the percentage of Room Knowledge and potentially
improve the sound quality from the initial correction.
17. Perform steps 1 thru 4 on page 24.
18. Rotate the NAVIGATE Control or use the Direc-
tional ◄ ► Push-buttons on the Remote Control
to select “RoomPerfect, Add Room Measurement”.
Refer to figure 90.
19.Press the SELECT Push-button and the “Place
mic. in room position no. 4” will appear. Refer to
figure 91.
20. Press the SELECT Push-button and the “Mea-
suring room position.no. 4” will appear. Refer to
figure 92.
The MEN220 will add the new measurement to the
previous measurements and recalculate for the best
room response.
ROOMPERFECT STATUS:
After the initial measurements have been taken the
results can be recalled at any time by performing the
following steps:
21. Perform steps 1 thru 4 on page 24.
22. Rotate the NAVIGATE Control (or use the Direc-
tional ◄ ► Push-buttons on the Remote Control)
to select “RoomPerfect, Status”. Refer to figure 93.
23. Press the SELECT Push-button and the “3 Room
Measurements Room Knowledge: 95% ”will ap-
pear. Refer to figure 94.
24. Rotate the ADJUST Control (or use the Direction-
al ▲ ▼ Push-buttons on the Remote Control) to
select “Focus 1, Room Corrections: 11%”. Refer to
figure 95.
Note: The RoomPerfect Room Correction Percent-
age is an indication of the degree of acous-
tic problems measured and corrected. This
includes room acoustics and Loudspeaker
placement in the room. The Correction Per-
centage is not an indication of performance of
the MEN220 or Loudspeaker.
RP BYPASS GAIN:
There may be a difference in overall volume levels
when comparing the RoomPerfect Focus or Global
Modes and the Bypass Mode. The RoomPerfect (RP)
Bypass Gain adjustment allows trimming the Bypass
Mode overall volume level by performing the follow-
ing steps:
25. Perform steps 1 thru 4 on page 24.
26. Rotate the NAVIGATE Control (or use the Direc-
tional ◄ ► Push-buttons on the Remote Control)
to select “RoomPerfect, RP Bypass Gain”. Refer to
figure 96.
27. Press the SELECT Push-button and the “RP By-
pass Gain , 0.0dB”will appear. Refer to figure 97.
Figure 90
RoomPerfect
<Add Room Measurem.>
Figure 94
3 Room Measurements
Room Knowledge: 95%
Figure 93
RoomPerfect
<RoomPerfect Status>
Figure 95
Focus 1
Room Corrections: 11%
Figure 96
RoomPerfect
< RP Bypass Gain >
Figure 97
RP Bypass Gain
0.0 dB
Figure 91
Place mic. in
room
position no. 4
Figure 92
Measuring room
position no. 4
Loading ...
Loading ...
Loading ...