Loading ...
Loading ...
Loading ...
25
Operating the Dishwasher
Note: With hidden controls, the door must be opened
before changing settings and closed after changing
settings.
9 WARNING
RISK OF INJURY
To avoid risk of injury, always use caution when
opening the door during or following a wash cycle
as hot water or steam may escape. Do not fully
open the door until water noises have stopped and
steam has subsided.
To reduce risk of injury, do not allow children to play
in or on the dishwasher.
When children become old enough to operate the
appliance, it is the responsibility of the parents/legal
guardians to ensure the children are instructed in
safe practices by qualified persons.
Protection against unintentional operation
Your dishwasher is equipped with a function that helps to
prevent unintentional operation (e.g. by children).
After starting the dishwasher, the dishwasher door has to
be closed within 4 seconds, otherwise the operation will
be paused. There will be a signal on the control panel
advising you to press the Start button again and close
the door.
This function will be activated when:
▯ pressing Start to begin a wash cycle
▯ setting Delay time and pressing Start
▯ opening the door while Delay time is active
▯ opening the door during a wash cycle.
Note: This function cannot be deactivated.
Operating the touch buttons
Buttons are sensitive and should be touched gently.
Avoid any grease or food particles resting on the buttons
as they could activate the dishwasher.
Wiping and cleaning can also activate the dishwasher.
For best results, use bare, clean hands when touching
the buttons.
To clean the touch buttons wipe them with a dry or
slightly damp cloth.
Changing the settings
The dishwasher has been preset with certain settings for
your convenience. You can change these factory
settings.
Here’s how to change the settings:
1.
Switch on ON/OFF switch (.
2.
Press and hold the ‹ button for 3 seconds.
In the display window H you will see •:‹... and ‘ .
3.
Press the ‹ button to access the individual
settings.
4.
Adjust the setting using the buttons - and + P.
5.
Press and hold the ‹ button for 3 seconds.
The chosen setting has now been stored in your
dishwasher.
AquaSensor
The AquaSensor is an optical measuring device which
measures the cleanliness of the rinse water.
The AquaSensor is used according to the wash cycle. If
the AquaSensor is active, “clean” rinse water can be
transferred to the next rinse and water consumption can
be reduced by 0.8–1-5 gal (3–6 liters). If the rinse water
is not yet clear, the water is drained and is replaced with
fresh water. In the automatic wash cycles the
temperature and running time can also be adjusted to
the degree of soiling.
Sensor setting
In its automatic programs the appliance uses sensors to
optimise their operation. The sensors adjust the strength
of the automatic programs according to the amount and
type of soiling. You can choose from three levels of
sensitivity for the sensors.
Sensor setting †“:‹‹: This setting is ideal for a mixed
load and heavily soiled utensils, but it also saves energy
and water.
Sensor setting †“:‹‚: This setting adjusts the
programme strength for the effective removal of food
remnants, even if the amount of soiling is low. The
energy and water consumption is adjusted accordingly.
Sensor setting †“:‹ƒ: This setting adjusts the program
strength for difficult conditions of use, for example firmly
dried on food remnants. This setting is recommended if
you are using biological or eco detergents which contain
smaller quantities of active agents. The energy and water
consumption is adjusted accordingly.
Time display
When a wash cycle is selected the remaining wash cycle
time is shown on the display H.
The wash cycle time is determined during the wash cycle
by the water temperature, the amount of dishes, as well
as the degree of soiling and may vary (depending on the
selected wash cycle).
Loading ...
Loading ...
Loading ...