Loading ...
Loading ...
Loading ...
Cleaning function en
23
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
The Ê symbol appears on the display if the appliance
needs to be descaled.
There are four steps in the descaling programme. For
hygiene reasons, the descaling programme must be
run through completely before the appliance is ready
for operation again. Descaling takes around 90–
110 minutes in total:
■ First step (1_4): Descale (approx. 65 minutes), then
empty and refill the water tank
■ Second step (2_4): Rinse (approx. 9 minutes), then
empty and refill the water tank
■ Third step (3_4): Rinse (approx. 9 minutes), then
empty and refill the water tank
■ Fourth step (4_4): Rinse (approx. 9 minutes), then
empty and dry the water tank
Start descaling
Caution!
■ Risk of damage to the appliance: Only use the liquid
descaler recommended by us for the descaling
programme. The length of time for which the
descaler is left to work is based on this product.
Using other descalers may damage the appliance.
Descaler order no. 311 680
■ Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This may damage the surfaces. If this does happen,
remove the descaling solution immediately with
water.
Note: Do not pour more than 150 ml of liquid into the
water tank throughout the descaling process.
First step (1_4)
1. Mix 100 ml water with 50 ml liquid descaler to make
a descaling solution.
2. Pour the descaling solution into the water tank and
insert the water tank.
3. Use the function selector to set the cleaning
functions O.
The O symbol and the cleaning functions appears
on the display. The first cleaning function is
highlighted.
4. Press the @ or A button repeatedly until the
Ê symbol is highlighted.
5. Turn the temperature selector.
"‹Ÿ" appears on the display. Descaling starts after a
few seconds.
6. After operation of the descaling programme "2_4"
appears on the display. Remove the water tank and
clean thoroughly with water.
Second step (2_4)
1. Fill the water tank with 150 ml water and insert it.
2. After operation of the rinse cycle, "3_4" appears on
the display. Remove the water tank and clean
thoroughly with water.
Third step (3_4)
1. Fill the water tank with 150 ml water and insert it.
2. After operation of the rinse cycle, "4_4" appears on
the display. Remove the water tank and clean
thoroughly with water.
Fourth step (4_4)
1. Fill the water tank with 150 ml water and insert it.
2. After operation of the rinse cycle, "3_4" appears on
the display. Remove the water tank and clean
thoroughly with water.
After descaling
1. Dry the water tank.
2. Reinsert the water tank.
Descaling is complete and the appliance is ready for
use again.
Descaling programme interrupted
If descaling is interrupted (for example, due to a power
failure or because the appliance is switched off), the
descaling symbol appears on the display after the
appliance is switched back on. You will be prompted to
rinse three times. The appliance cannot be used for
other operations until the third rinse cycle comes to an
end. If you set another operation, "’‚Ÿ" (Cleaning)
appears on the display. Repeat the interrupted
descaling programme after rinsing.
1. Empty the water tank and clean thoroughly with
water.
2. Insert the empty water tank.
3. Use the function selector to set descaling.
4. Turn the temperature selector.
"‹Ÿ" appears on the display. After a few seconds,
the remaining liquid pumped back.
5. Empty the water tank and clean thoroughly with
water.
6. To rinse the steam system, run the three rinse cycles
in the descaling programme.
7. Restart descaling.
Loading ...
Loading ...
Loading ...