Loading ...
Loading ...
Loading ...
14
P5 Stereo Control Amplifier
Network Configuration
Stativ IP
Disabled
DHCP
NETWORK
SETUP
Status
Renew IP Address
Network Standby
IP Address
Subnet Mask
Network Type
This Network menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
T
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
T
/
D
buttons and press
the Enter
K
button to confirm.
Status: If the network is properly configured and attached to the network then
“Connected” will be displayed. If the network is not properly configured or not
connected to a network, “Disconnected“ will be displayed.
Network Type: In most systems, set the IP ADDRESS MODE to DHCP. This
setting will allow your router to assign an IP address to the P5 automatically.
If your network uses fixed IP addresses, set the IP ADDRESS MODE to Static.
To disable the IP connection set this option to DISABLED.
Options include: DHCP (Default), Static IP, Disabled.
Renew IP Address: Disabled if Network Type is Static or Disabled. If Network
Type is DHCP then select Yes and press the Enter
K
button to renew the IP
address.
Network Standby: When set to Enabled the unit will maintain the Ethernet
IP connection even in Standby Mode allowing the unit to be powered on via
IP. If Disabled the unit will not power on from the IP connection and must use
either the front panel, IR remote or RS232 to power on the unit.
Options Include: Disabled (Default), Enabled
NOTE When Network Standby is enabled the unit will consume additional
power.
IP Address/Subnet Mask/Gateway/DNS: Disabled if Network Type is DHCP
or Disabled. If STATIC mode is selected you must configure all settings for the
network including IP Address, Subnet Mask, Gateway and DNS Server. Press
the Enter
K
button to activates the first digit in the line you want to change,
then use the
T
/ arrow
D
buttons to adjust the values and press the Enter
K
button to cycle to the next digit. When the proper IP information is configured
press the Enter
K
button to move the cursor back to the previous menu and
accept the settings. After entering the STATIC IP address information the
network will be tested and connection status reported.
NOTE: For more information regarding network connection please
contact your authorized Michi dealer.
NOTE: A network connection is not required for the P5 to operate.
Esc
0 1 2
8 9 A
H I J
B
Q R S T
Z
K L M N
U V W X
C D E F
3 4 5 6
O
7
G
P
Y
-
SOURCE
SETUP
Enabled
Volume
Audio Mode
Name
Bass
Input
1. Press the
T
/
D
arrow buttons on the remote control to change the first
letter, scrolling through the list of available characters.
2. Press the Enter
K
button on the remote control to confirm that letter and
move to the next position.
3. Repeat steps 1 and 2 until all ten characters have been completed. The
final press of the Enter
K
button saves the new name. Or select the “Esc
“ button on the OSD to confirm if you have less than ten characters to enter.
Enabled: Allows a source input to be enabled and appear in the list of source
input options when using the source selection on the front panel or IR remote
control. Unused sources should be set to disabled by selecting the “No” option.
Options include: Yes(Default), No.
Volume: Configures a Fixed Volume level for a specified input. This volume
level is immediately set when this source input is selected and cannot be
changed using the front panel or IR remote. This is useful for input sources
that include their own volume setting like common Apps on phones or tablets.
Options include: Variable (Default), 30 - 90.
Audio Mode: Configures audio mode to Direct Bypass or Tone Enabled.
Options include: Direct Bypass (Default), Tone Enabled.
Bass: Bass setting is enabled when Audio Mode is set to Tone Enabled.
Options include: +10 to -10 (Default 0).
Treble: Treble setting is enabled when Audio Mode is set to Tone Enabled.
Options include: +10 to -10 (Default 0).
Press the SETUP button
B
on the remote control to exit the setup menu or
select “Back” on the OSD to return to the main menu.
Loading ...
Loading ...
Loading ...