Loading ...
Loading ...
Loading ...
13
English
NOTE All Michi products will respond to the same Power On and Off
commands to simplify the power control when multiple products are
installed. To control the power using the IR remote follow the instructions
above and point the remote control at the Michi products. If a unit does
not respond to a power on or off from the IR remote simply PUSH or PUSH
HOLD the power button again to resend the desired command.
SETUP B: The SETUP button activates the OSD setup screen on the front
display. Push the SETUP button again to move to the previous setup menu as
a “back” key or exit setup menu if on the first level of setup menu.
SOURCE 1C: The SOURCE knob on the front panel and the SOURCE button
on the remote control selects the input signal source. From the front panel
turn the SOURCE knob to select the source. After 1 second of no action the
listed source will be selected as the active source.
On the IR remote push the SOURCE button and navigate to the desired source
using the
T
/
D
buttons and push the Enter
K
button to activate the source.
NOTE Only sources that are configured as ACTIVE in the setup menu
will be displayed as options.
DISPLAY G: Dims the front display. To dim the display PUSH-HOLD the
DISPLAY G button on the remote control for 3 seconds. To turn on the display
to the level of brightness configured in the setup menu push and release the
DISPLAY G button.
NOTE: The DISPLAY button is common for all Michi models. To Dim or
enable the display PUSH or PUSH-HOLD the button and point to the Michi
products. If a unit does not respond to a DISPLAY command simply send
the command again using a PUSH or PUSH-HOLD.
AUDIO H: The AUDIO button allows temporary adjustments to the Balance,
Bass and Treble settings. To change these settings push the AUDIO button
on the remote control and navigate to the desired setting using the
T
/
D
button and push the Enter
K
button. Use the
T
/
D
button to change the
value. Push the AUDIO button again to exit the menu or to exit the Audio menu.
NOTE A properly setup Hi-Fi system should not require changes to the
Bass or Treble setting. Use these adjustments sparingly.
NOTE These settings are temporary and not saved when the P5 is
powered off to Standby. For permanent changes, configure the audio
settings in the setup menu.
Button
E
: Push the button once to mute the audio. An indication
appears in the front panel on-screen display. Press the button again to restore
the previous volume level.
VOLUME Knob 3 and VOL +/- Buttons
F
: The VOLUME +/- buttons on the
remote and the rotary control on the front panel provide the master VOLUME
control, adjusting the output level.
Main Menu
SOURCE
SETUP
NETWORK
AUDIO
DISPLAY
SYSTEM
The Setup menu provides access to OSD screens for various configuration
options. Setup menu is reached by pressing the SETUP
B
button on the
remote. To select the desired menu, move the highlight using the
T
/
D
arrow buttons and press the Enter
K
button on the remote control. Press the
SETUP
B
button again to return to the previous menu or select “EXIT“ on the
OSD to end setup and return to normal operation.
Source Configuration
Coax 2
Coax 3
OPT 1
OPT 2
SOURCE
SETUP
Name
Enabled
Volume
Input
Coax 1
Audio Mode
A key step in setting up the unit, is to configure each source input using the
Source Setup screens. Configuring the inputs allows you to set defaults for a
number of settings including the type of input connector, the desired audio
mode, custom labels that appear in the displays when a source is selected,
and many more options.
This Source menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
T
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
T
/
D
arrow buttons and
press the Enter
K
button to confirm.
INPUT: Changing this input allows you to select a specific input for configuring.
(COAX , OPT , PCUSB, BLUETOOTH, COMPACT DISC, PHONO, TUNER,
AUX , XLR )
NAME: The name of the source can be customized. For example Aux 1
can be named “TV” for easier reference. The default NAME is the same as
the SOURCE. Place the highlight on this option and use the
T
/
D
arrow
buttons on the remote control to select “Custom” then press the Enter
K
button to enter the source name edit sub menu as below.
Loading ...
Loading ...
Loading ...