Loading ...
Loading ...
Loading ...
COMMERCIAL MODE SETUP
104
COMMERCIAL MODE SETUP
001111 -- KKEEYY DDEEFFEEAATT ((KKeeyybbooaarrdd DDeeffeeaatt))
If set to 1, key defeat prevents the end user from
accessing the on-screen menus with the TV front
panel—MENU, SELECT, and Left / Right arrow keys do
not function. If set to 0, those keys do function.
NNOOTTEE::
The menus can always be accessed by press-
ing MENU on the remote.
001122 -- IIRR BBAANNKKSS EENN
(IR Banks Enable)
For direct access to a particular Channel Bank. When
enabled, installer can access a channel bank by
inputting the IR code for the bank.
001133 -- SSCCAANN MMOODDEE ((FFuunnccttiioonnaall aafftteerr 22--55--
55++MMeennuu sseettuupp ttrraannssffeerr))
Allows variation in setting the TV On/Off with Channel
UP/DOWN. You may opt for TV channels only; TV
channels + Off/ON; with these settings for Scan Mode:
SCAN MODE Characteristics
0 Channel up/down keys change channels only.
1 Channel down below the lowest channel
(or channel up higher than the highest)
and TV turns off.
001144 -- SSTTRRTT CCHH IINN SSMM
(Start Channel in Scan Mode) If set to 1, installs TV
On/Off event below the start channel at TV turn On. If
set to 1, the user can select channels with either
Channel Up/Down or by direct keypad entry. If set to
0, only those channels that are entered for scanning
can be selected.
001155 -- SSLLEEEEPP TTIIMMEERR
If set to 1, the SLEEP TIMER feature may be used. If
set to 0, the Sleep Timer is not available.
001166 -- EENN TTIIMMEERR ((EEnnaabbllee OOnn//OOffff TTiimmeerrss))
If set to 1, Timer function is available to end user and
enabled continuously. Set to 0 to disable On/Off
Timers. (Clock must be set in order to use Timers.)
001177 -- AALLAARRMM **
Gives the installer the option of making the Alarm
function available to the end user. If set to 1, Alarm
function is available to end user. Set to 0 to disable the
Alarm function.
NNOOTTEE::
Clock must be set before the Alarm function
will work.
002200 -- FFEEAATTUURREE LLEEVVEELL
IInnssttaalllleerr sshhoouulldd lleeaavvee iitteemm 2200 FFEEAATTUURREE LLEEVVEELL
sseett ttoo 11 ((ddeeffaauulltt))..
Default set to ZEN 1 for Zenith IR codes
remote control operation. Set O, P LBL for
Zenith Private Label IR remote control opera-
tion.
Warning: Do not set to “0” or remote will not control
TV.
002211 -- VV--CCHHIIPP ((PPaarreennttaall CCoonnttrrooll))
Set to 1 to activate V-Chip (Parental Control); have it
available to end user to filter and control or otherwise
restrict programming content that can appear. Set to 0
to turn V-Chip feature Off, not available to end user;
no programming restrictions can be set.
** OOnnllyy aaffffeeccttss FFuunnccttiioonn MMeennuu iiff eennaabblleedd bbyy
ssoommee PPPPVV pprroovviiddeerrss..
002222 -- MMAAXX BBLLKK HHRRSS ((MMaaxxiimmuumm BBlloocckk HHoouurrss))
Sets hours from 0 to 99 for the maximum V-Chip
(Parental Control) block hours. Default setting is for 12
blocking hours.
002233 -- CCAAPPTTIIOONN LLOOCCKK
Set to 1 to restore previous caption On/Off state after
turn Off. If set to 0, captions are always Off at turn
On.
002255 -- FFUUNNCCTTIIOONN PPRREE ((FFuunnccttiioonn PPrreevviieeww))
Set to 0 to suppress CHANNEL PREVIEW from the
FUNCTION menu with some Pay-Per-View systems.
002277 -- HHOOSSPPIITTAALL MMOODDEE
The default is 2 (which favors most hospitals). With
this setting two things are affected: Channel Banks 1, 2
and 3 are accessible, while Bank 4 can be made inac-
tive by removing all the channels from Channel Bank 4.
Then, if Channel Bank 4 is selected when the TV is
turned on, the TV screen will show “Inactive TV”. The
Channel Bank 4 setup allows the hospital to present
TV viewing options to the patient. The patient can
select programming options available in either Bank 1,
2 or 3. Channel Banks are available in all hospital
modes 1 an 2.
• The IR code that will control the TV depends on Item
20-I Feature Level setting.
Hosp. Mode = 0 Hospital Mode disabled.
Hosp. Mode = 1 Zenith P.L. IR Code (Bed 1)
Hosp. Mode = 2 Zenith IR Code (Bed 2)
002288 -- CCHH.. OOVVEERRIIDDEE ((CChhaannnneell OOvveerrrriiddee))
If set to 1, the user can select channels with either
Channel Up/Down or by direct number keypad entry. If
set to 0, only those channels that are active in the TVs
memory can be selected.
002299 -- OOLLDD OOCCVV ((OOnn CCoommmmaanndd VViiddeeoo
TTMM
))
Set to 1 for operation with systems from On Command
Corporation.
(Continued on next page)
Detailed Descriptions of Installer Menu Items
Loading ...
Loading ...
Loading ...