Loading ...
Loading ...
Loading ...
English Operating Instruction – Lawnmower with IC engine
12
Fig. 3
Set the cutting height
of the grass
as required.
Setting option (depending on
mode
l) from approx. 3
cm to
maximum 9
cm.
Note
If appliances have individual wheel
ad
justment, set all wheels to the
same height.
Model A
Attach the wheels in the position
required.
Model B
Pull the flap and snap into place
in the position required.
Model C
Advance or push back the lever of
the central vertical adjustment and
snap into place in the position
required.
Locking front wheels
(only appliances with lockable front
wheels)
Fig. 4
Lock wheels to drive straight ahead
–
set the wheels in forward position
and put hoop into large hole.
Wheels are freely movable – put
cla
mp into large hole.
Fill up with fuel and check the
oil level
Fill up with lead-free petrol (see
engine manual).
Fill fuel tank up to max. 2 cm
below the lower edge of the inlet
nozzle.
Close fuel tank tightly.
Check oil level and, if required,
top up (see Engine manual).
Starting the engine
Fig. 5
Danger
To prevent injury:
– Do not start the engine when you
are standing in front of the
ejector;
– Keep hands and feet well away
fro
m the cutting blade;
– never place your hands, feet, or
other parts of the bo
dy near
rotating parts; Always keep away
from the ejector.
Before starting the engine,
di
sengage the clutches for all
cutters and drives.
Do not tip the appliance when
starti
ng. Keep the appliance on an
even surface with little or the
shortest possible grass.
Information about the engine
Observe the information in the
en
gine manual.
– Some models have no throttle
and
the speed is adjusted
automatically. The engine
always runs at optimum speed.
– Even if the engine is warm, it may
be necessary to actuate the
choke or the primer.
– Some models have no choke and
no pri
mer. The engine is
automatically set to the particular
starting process.
If the engine
is cold:
Open the fuel tap (if fitted).
Units with choke :
Set the choke lever to , or pull
out the choke and set the
accelerator lever (if
fitted) to
/max. (Fig. 5A)
or
Set the accelerator lever to -
fig. 5A.
Appliances with primer:
Press primer forcefully 1–5x and
move throttle (if fitted) to
/max. – fig. 5B.
If the engine
is warm:
Open the fuel tap (if fitted).
Set throttle (if available) to
/max. – Fig. 5B
Appliances without electric starter:
Fig. 5C
Stand behind appliance – Press
and hold safety lever.
Slowly pull the starter cable grip
until you feel resistance, and
then pull quickly and strongly. Do
not let the pull-starter handle
spring back, but slowly guide it
back.
For appliances with electric starter:
Fig. 5D
Disconnect charger from power
supply and unit.
Stand behind appliance – Press
and hold safety lever.
Turn ignition key on the steering
handle until the engine starts
(start attempt max. 5 seconds,
wait 60 seconds before the next
attempt).
Note:
If appliances feature electric
starter, the eng
ine (depending on
model) can also be started
manually with the pull-starter
handle.
When the engine is running:
After starting the engine
(depending on the model):
– return the choke (if fitted),
– move the accelerator lever (if
fi
tted) between /max and
/min so that the engine can
warm up briefly.
Set the throttle to full throttle (if
available).
Note
If you need more information about
op
erating the engine, please refer
to the engine manual.
Stopping the engine
Fig. 7
Bring throttle (if available) into
position /min.
Release the safety hoop. The
engine and the cutting tool stop
after a short time.
Working with the snow-
clearing machine
Engaging/disengaging gear
drive
(only in the case of appliances with
gear drives)
Fig. 6A, B, C
Wheel drive activation
/ :
Pull and hold the lever/hoop.
Wheel drive deactivation
/ :
Release lever/hoop.
!
Not for Reproduction
Loading ...
Loading ...
Loading ...