5025 User Manual

No. Installer Setting Factory Setting Comments

(Notes follow this table) Default Options (More information follows this table)

9 1st Stage Fan Control HG FAN 1 HG FAN 1 Select for 1st stage Gas heating

[note 3] HE FAN 1 Select for 1st stage Electric heating

10 Emergency Heat] HE EMER HE EMER Select for Electric Emergency Heat

Fan Control [note 2] HG EMER Select for Gas Emergency Heat

11 Reversing Valve REVO REVO

Select for cool active Reversing Valve (O terminal)

(O/B Terminal) [note 4] REVB

Select for heat active Reversing Valve (B terminal)

12 Fossil Fuel AE AUX AE AUX

Select for Electric Auxiliary heat (with compressor)

Backup Heat [note 2] AG AUX

Select for Gas Auxiliary heat (without compressor)

13

Compressor Power Outage

oF CPOP oF CPOP Disables Power Outage Lockout Delay

Protection [notes 2, 5] on CPOP Enables Power Outage Lockout Delay

14 AC Power Interrupt

AC oF MONR

AC oF MONR Disables AC Power Interrupt Warning

Warning [note 5] AC on MONR Enables AC Power Interrupt Warning

15 Compressor Short 5 CSCP 5, 4, 3, 2 or Select a compressor short cycle protection delay

Cycle Protection [note 6] 0 CSCP of 5, 4, 3, 2 or 0 minutes

16 Residual Cooling 60 FAN 90, 60, 30 Select a Residual Cooling Fan Delay of 90, 60,

Fan Delay [note 6] or 0 FAN 30 or 0 seconds.

17 Circulating Fan Lock oF CIRC oF CIRC Disables Circulating Fan Lock mode

on CIRC Enables Circulating Fan Lock mode

18 Adaptive Recovery oF REC oF REC Disables Adaptive (early) Recovery mode

Mode (ARM™) [note 7] on REC Enables Adaptive (early) Recovery mode

19 Indoor Remote Sensor I SENS I SENS Temperature is sensed from thermostat only.

Control* [note 8] E SENS Temperature is sensed from remote sensor only.

A SENS Temperature is combined with the thermostat

and the remote sensor.

20 Lockout Security Level 2 LOCK 2 LOCK If locked – Complete lockout is enabled

1 LOCK If locked – Partial lockout is enabled (SpeedBar

®

is still functional)

21 Humidiﬁcation OFF OFF Disables Humidiﬁcation

DEP Enables Dependent Humidiﬁcation

IND Enables Independent Humidiﬁcation

22 Auto Humidity Set AUTO AUTO Maximum humidity setpoint is limited based

Point Limit [note 10] on outdoor temperature.

MAN

Enables manual humidity control from thermostat.

23 Dehumidiﬁcation OFF OFF Disables Dehumidiﬁcation

DEP Enables Dependent Dehumidiﬁcation

IND Enables Independent Dehumidiﬁcation

24 Dehumidiﬁcation Over 1.0 LIM 1.0, 2.0 or Select a dehumidiﬁcation over cooling limit of

Cooling Limit [note 11] 3.0 LIM 1.0°, 2.0° or 3.0° F (.5°, 1.0° or 1.5° C)

25 Dehumidiﬁcation

Terminal

NI NI Selects normally inactive relay (N/O)

(D) Output [note 12] NA Selects normally active relay (N/C)

26 Auto Changeover 3 BAND 2, 3, 4 or 5 Select a Dead Band of 2°, 3°, 4° or 5˚ F

Dead Band [note 9] BAND (1°, 2° or 3° C) for Auto Changeover mode.

11 Installer Manual

No. Installer Setting Factory Setting Comments

(Notes follow this table) Default Options (More information follows this table)

27 Compressor Balance NO BALC NO BALC Disables Balance Points

Point [notes 2, 10] 0-15 BALC Select a Compressor Balance Point of 0° to 15°F

(-18° to 10°C)

28 Auxiliary Heat Balance NO BALA NO BALA Disables Balance Points

Point [notes 2, 10]

70-40 BALA

Select a Auxiliary Heat Balance Point of 70° to 40°F

(21° to 4°C)

29

Heat Set Point Upper Limit

90LIM 90-60 LIM

Select a Heat Set Point Upper Limit of 90° to 60°F

(32° to 10°C)

30

Cool Set Point Lower Limit

45LIM 45-80 LIM

Select a Cool Set Point Lower Limit of 45° to 80°F

[note 6]

(7° to 27°C)

*When a Braeburn

®

outdoor sensor is connected, the thermostat automatically recognizes it. Press PROG and HOLD at the

same time to display outdoor temperature.

NOTE: Additional options such as Service Monitors, setting the lock code, etc. are located in the

User Settings – See User manual for information on setting these options.

NOTES - Installer Settings

1 Only available if Residential proﬁle was selected in option 1.

2 Only available if a 2 stage system type was selected in option 6.

3 Only available if a Conventional system was selected in option 6.

4 Only available if a Heat Pump system was selected in option 6.

5 Only available if the 24 Volt AC common wire is connected to the C terminal.

6 Not available if a heat only hydronic system is selected in option 6.

7 Only available if a programmable proﬁle was selected in option 2.

8 Only available if a Braeburn® indoor remote sensor was connected.

9 Only available if auto changeover was enabled in option 5.

10 Only available if a Braeburn outdoor sensor was connected.

11 Only available if Dependent Dehumidiﬁcation was selected in option 23.

12 Only available in Independent Dehumidiﬁcation mode when humidiﬁcation is disabled.

Detailed Explanation of Installer Settings (also see NOTES above):

1 Proﬁle – Selects a residential (RES) or commercial (COMM) proﬁle. If residential is selected, 4 programming

events per day are available. If commercial is selected, 2 event, 7 day programming is available.

2 Programming Mode [note 1] – Selects the programming mode, either full 7 day or 5-2 day (weekday/

weekend) programming or non-programmable.

3 Clock Type – Selects either a 12 hour or 24 hour clock.

4 Temperature Scale – Selects a temperature scale of either °F or °C.

5 Auto Changeover – Selects auto changeover on or off. When auto changeover mode is enabled and

selected, the system automatically switches between heating and cooling modes. There is a 5 minute

delay when switching from heating to cooling or cooling to heating in auto changeover mode.

NOTE: Also see “Auto Changeover Dead Band” in option 26.

User Manual - Page 11