OWNER’S MANUAL AND SAFETY INSTRUCTIONS
SALT CELL WATER CHLORINATOR SYSTEM
ITEM # 90184 (15K GALLONS), 90185 (25K GALLONS), 90186 (40K GALLONS)
SAVE THIS MANUAL. KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATION, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL, OR THE MONTH AND YEAR OF PURCHASE IF
PRODUCT HAS NO SERIAL NUMBER
FOR QUESTIONS, PLEASE CALL CUSTOMER SERVICE: 909.628.0880
ITEM # 90184 (15K GALLONS), 90185 (25K GALLONS), 90186 (40K GALLONS)
SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and instructions
may result in injury and/or property damage. Save all warnings and instructions for
future reference.
The warning and safety instructions in this manual are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care must be exercised when operating or
cleaning tools and equipment. Always contact your dealer, distributor, service agent or manufacturer
about problems or conditions you do not understand before operating the product.
1
Please note, the total working hours for the salt cell should be less than 8 hours total per day. If you are
using a variable speed pump for 24 hours a day be sure to adjust the chlorine output to 25-30%. If the
pump is only running 10 hours per day adjust the chlorine output between 60-80%.
You can use this calculation to calculate the appropriate chlorine output for your pool, suggest at 6
hours per day.
Pump running for 24 (Hours a day)*25% (Chlorine Output)=6hr (cell run time per day at 25%).
Pump running for 20 (Hours a day)*30% (Chlorine Output)=6hr (cell run time per day at 30%).
Pump running for 15 (Hours a day)*40% (Chlorine Output)=6hr (cell run time per day at 40%).
Pump running for 12 (Hours a day)*50% (Chlorine Output)=6hr (cell run time per day at 50%).
Pump running for 8 (Hours a day)*75% (Chlorine Output)=6hr (cell run time per day at 75%).
Start the Variable Speed pump on a low speed and kick the speed up until the salt system works.
cell requires software r1.5 or newer to be compatible. These revisions started in 2009. Press the diagnostics
button on your control 7 times to see your systems current software revision level.
series cell is not compatible with Hayward® Automation system.
ATTN: THE salt cell is not produced, manufactured, or sold by Hayward. Neither nor its salt cell is
afliated with Hayward Industries, Inc. The use of above model and system compatibility designations
are included for informational purposes only.
SAFETY WARNINGS INSTALLATION AND MAINTENANCE
1 2
INSTALLATION & OPERATION
IMPORTANT: Always make sure the input power is completely disconnected and all pool equipment
is shut off before attempting any service procedures. All service should be performed by a qualied
professional.
Remove the old Cell from the plumbing by loosening the threaded collars on both ends of the Cell.
Disconnect the Cell Cord from the control panel.
Inspect the O-Rings on the plumbing unions. If damaged or worn, replace before installing the new
Cell.
Position the new series Replacement Cell between the plumbing unions. Tighten the two threaded
collars by hand for a water-tight seal, do not over-tighten. Plug the Cell Cord into the control panel.
Once power is restored to the control panel (concurrently with the pump and lter), the system can
now be operated as instructed in the original manufacturer’s product manual.
MAINTENANCE
The replacement Cell operates in the same way as your original Cell. As with your prior system, it may
occasionally be necessary to remove the mineral deposits which can form inside. Cleaning frequency
is entirely dependent on your pool’s water chemistry, which depending on environment and chemicals
added, can change to become more or less scale forming. Follow the cleaning instructions in the
original manufacturer’s product manual.
DISCLAIMER
3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
MADE IN CHINA
