

1
IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances,basic precautions should always be followed to
reduce the risk of fire,electric shock,and injury to persons,including the following:
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. If provided, always use handles when moving this heater. Keep
combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater and keep them
away from the sides and rear.
3. Extreme caution is necessary when any heater is left unattended and or used
near children or the disabled
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater
or return heater to authorized service facility for examination, electrical or
mechanical adjustment, or repair.
6. Do not use the heater outdoors.
7. This heater is not intended for use in bathrooms,laundry areas, or similar
indoor locations. Never position the appliance where it may fall into a bathtub
or come in contact with water.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be tripped over.
9.
CAUTION:
This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of shock, this plug is intended to fit only one way in
a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician. DO NOT attempt to compro-
mise this safety feature. To do so could result in an electric shock hazard.
10. This heater draws 12.5 amps during operation. To prevent overloading a
circuit, do not plug the heater into a circuit that already has other appliances
working.
11.
CAUTION:
It is normal for the plug to feel warm to the touch; however, a
loose fit between the AC outlet and plug may cause overheating and distor-
tion of the plug. Contact a qualified electrician to replace loose or worn outlet.
12. To disconnect the heater, first turn controls to off, then remove plug from outlet.
Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening
as this may cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do
not use on soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas
where gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not recommend-
ed by the manufacturer may cause fire, electric shock, or injury to persons.
17.
CAUTION
: Always plug heaters directly into a wall outlet. Never use with an
extension cord or reloadable power tap (outlet/power strip).
18. The output of this heater may vary and its temperature may become intense
enough to burn exposed skin. Use of this heater is not recommended for persons
with reduced sensitivity to heat or an inability to react to avoid burns.
19. Disposal of oil contained within should be in accordance with applicable regional,
national, and local laws and regulations.
20.
Warning
: In order to avoid overheating, do not cover the heater.
21.
CAUTION
: to prevent electric shock, match wide blade of plug to wide slot
and fully insert.

2
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. If provided, always use handles when moving this heater. Keep
combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater and keep them
away from the sides and rear.
3. Extreme caution is necessary when any heater is left unattended and or used
near children or the disabled
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater
or return heater to authorized service facility for examination, electrical or
mechanical adjustment, or repair.
6. Do not use the heater outdoors.
7. This heater is not intended for use in bathrooms,laundry areas, or similar
indoor locations. Never position the appliance where it may fall into a bathtub
or come in contact with water.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be tripped over.
9.
CAUTION:
This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of shock, this plug is intended to fit only one way in
a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician. DO NOT attempt to compro-
mise this safety feature. To do so could result in an electric shock hazard.
10. This heater draws 12.5 amps during operation. To prevent overloading a
circuit, do not plug the heater into a circuit that already has other appliances
working.
11.
CAUTION:
It is normal for the plug to feel warm to the touch; however, a
loose fit between the AC outlet and plug may cause overheating and distor-
tion of the plug. Contact a qualified electrician to replace loose or worn outlet.
22.
“SAVE THESE INSTRUCTIONS”
12. To disconnect the heater, first turn controls to off, then remove plug from outlet.
Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening
as this may cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do
not use on soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas
where gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not recommend-
ed by the manufacturer may cause fire, electric shock, or injury to persons.
17.
CAUTION
: Always plug heaters directly into a wall outlet. Never use with an
extension cord or reloadable power tap (outlet/power strip).
18. The output of this heater may vary and its temperature may become intense
enough to burn exposed skin. Use of this heater is not recommended for persons
with reduced sensitivity to heat or an inability to react to avoid burns.
19. Disposal of oil contained within should be in accordance with applicable regional,
national, and local laws and regulations.
20.
Warning
: In order to avoid overheating, do not cover the heater.
21.
CAUTION
: to prevent electric shock, match wide blade of plug to wide slot
and fully insert.

3
Ɣ Check before turning on the machine
1. Check if the power wire is in good condition.
2. The product adopts 120V 60Hz AC power supply, before use, please confirm if the rated current of
the power socket meets the local requirements with safe grounding device, otherwise, please
replace it with the qualified socket.
Ɣ Place heater on firm, leveled surface
Uneven surface may possibly cause the turnover switch to engage, causing the heater not to work
once turned on.
Ɣ Power Switch Knob
Turn the Power selection knob to select between 4 functions: (Heat) 900W LOW, (Heat) 1500W HIGH,
(Fan) LOW, (Fan) HIGH.
Ɣ Turn off the Heater
A. Turn the Power Switch Knob to OFF position.
B. Remove the power plug, store the heater after the entire machine unit has cooled down.
Ɣ Safety Protection
1.Overheat protection:This heater includes an Overheat Protection Feature that shuts the unit off if it
overheats due to abnormal conditions. If this occurs turn the heater “OFF”, unplug it, and inspect and
remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, plug it back in,
and resume normal operation.
2.Inversion protection: The white “button” on the bottom of the unit is a tip-over switch. When the
unit sits upright, the button is pressed and the unit will work. If the unit falls over, the button is
released and the unit will turn off.
PARTS AND FEATURES
OPERATING INSTRUCTIONS
Power on indicator
Power selection knob
Safety grille
Off
(Fan) Low
(Fan) High
(Heat) Low
(Heat) High
Do not
Cover

4
ADDITIONAL FEATURES
This heater has additional features:
x
TROUBLESHOOTING
If your heater fails to operate, please follow these instructions:
x Ensure that your circuit breaker or fuse is working properly.
x Be sure the heater is plugged in and that the electrical outlet is working properly.
x Check for any obstruction. If you find any obstruction, turn the heater “OFF”. Unplug
the heater and wait a few minutes for it to cool down. Carefully remove the
obstruction. Plug the heater in and turn it on again by referring to the OPERATING
INSTRUCTIONS.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE WARRANTY
INFORMATION FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE
HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR
PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CONTACT US BY
REFERRING TO
THE SERVICE & SUPPORT INFORMATION
ON THE FOLLOWING PAGE.
CLEANING AND STORAGE
It is recommended that the heater be cleaned at least one time during the operating season in
order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF
AND UNPLUG THE HEATER BEFORE CLEANING. Be sure to save the box for off-season storage.
x Turn the heater “OFF”, unplug it and wait for the heater to cool down.
x Use a dry cloth to clean only external surfaces of the heater.
x Do not use any cleaning agents or detergents.
x Never immerse the heater in water.
x Pack the heater in the original carton and store it in a cool and dry place.
SPECIFICATIONS
Model No.: PSF10M6ASB
Voltage: 120V, 60Hz
Current: Maximum continuous draw: 12.5 Amps.
Output: 5200 BTUs
Power: LO = 900 Watts, HI = 1500 Watts
Convenient Carry Handle – allows for effortless portability from room to room.

5
SERVICE & SUPPORT
In the event of a warranty claim or if service is required for this heater, please
contact us at the following:
Tel: 1-866-646-4332
For questions or comments, please write to:
Midea America Corporation
5 Sylvan Way, Suite 100
Parsippany, NJ 07054
For your records, staple your sales receipt to this manual and record the following:
DATE OF PURCHASE:
PLACE OF PURCHASE:
(STAPLE SALES RECEIPT HERE)
NOTE: PROOF OF PURCHASE IS REQUIRED FOR
ALL WARRANTY CLAIMS
Printed in China

1-844-224-1614

6
ONE (1) YEAR LIMITED WARRANTY
Please read all instructions before attempting to use this product.
Midea America Corporation warrants as limited herein to the original purchaser of retail that
each new Fan-forced heater, shall be free of defects in material and workmanship for a
period of one (1) year from the date of original purchase. This one (1) year warranty is
limited to the heating elements, motor, and electric control circuit board.
In the event of malfunctions or failure of your Fan-forced heater, simply
deliver or send the heater, postage prepaid along with PROOF OF PURCHASE, within the
warranty period of one (1) year, to Midea America Corporation.Midea America Corporation
reserves the right to inspect the claimed defective part or parts to determine if the defect or
malfunction complaint is covered by this warranty. Midea America Corporation shall, within
sixty (60) days after receipt of the product,at its option, repair and/or replace the defective
part or parts free of charge. This warranty shall only cover defects arising from normal usage.
Midea America Corporation assumes no responsibility whatsoever if the Fan-forced heater
should fail during the warranty period by reason of:
Misuse, negligence, physical damage or accidents.
Lack of maintenance (see instructions for proper maintenance).
Repair by any unauthorized party during the warranty period.
Damage caused by connection to an improper input voltage (see specification
label on your heater).
Midea America Corporation makes no further warranties or representations, express or
implied except those contained herein. No representative or dealer is authorized to assume
any other liability regarding the Fan-forced heater. The duration of the implied warranty
granted under State law, including warranties of merchantability and fitness for particular
purpose are limited in duration should the duration of the express warranty grant it hereunder.
Midea America Corporation shall in no event be liable for direct, indirect, special or
consequential damages.
Some states do not allow limitations on how long an implied warranty lasts, and/or the
above limitations or exclusion may not apply to you. This warranty gives you specific legal
rights and you may have other rights which vary from state to state.


1
INSTRUCCIONES IMPORTANTES
POR FAVOR LEA Y GUARDE ESTAS INSTRUCCIONES DE SEGURIDAD
Al utilizar cualquier tipo de aparato eléctrico, se deben tomar en cuenta
precauciones básicas de seguridad para reducir el riesgo de incendio, lesiones
y choques eléctricos, incluyendo las siguientes:
1. Lea todas las instrucciones antes de usar.
2. Este aparato estará caliente. Para evitar quemaduras, evite tocar su
superficie. Si el aparato los incluye, siempre utilice los mangos al mover.
Mantenga materiales inflamables, tales como muebles, almohadas, ropa de
cama, papeles, ropa y cortinas a una distancia de al menos 0,9 metros (3
pies) de la parte delantera y alejados de la parte posterior y los lados.
3. Es necesaria extrema precaución cuando el calefactor es utilizado por o
cerca de los niños o personas vulnerables y siempre que el calefactor se
deje desatendido.
4. Desenchufe el aparato cuando no esté en uso.
5. No operar con un cable o enchufe dañado, o después de que haya
funcionado mal o se haya caído o dañado de alguna manera. Lleve el
calefactor al fabricante para su examen, ajuste eléctrico o mecánico, o
reparación.
6. No utilizar al aire libre.
7. El calefactor no está diseñado para uso en baños, áreas de lavandería o
similares lugares húmedos. Nunca coloque el calefactor donde pueda caer
en una bañera u otro recipiente de agua.
8. No pase el cable de alimentación por debajo de alfombras. No cubra el cable
con tapetes, alfombras o similares. No tienda el cable debajo de muebles u
otros electrodomésticos. Coloque el cable lejos de áreas de tráfico y donde
no pueda provocar tropiezos.
9.
PRECAUCIÓN:
Este aparato tiene un enchufe polarizado (una pata es más
ancha que la otra). Para reducir el riesgo de descarga eléctrica, el enchufe
está diseñado para encajar en un tomacorriente polarizado de una sola
manera. Si el enchufe no encaja por completo en el tomacorriente, inviértalo.
Si aún así no encaja, llame a un electricista calificado. NO intente violar esta
medida de seguridad. Esto podría resultar en una descarga eléctrica.
10. Este calefactor consume 12,5 amperios durante el uso. Para prevenir la
sobrecarga de un circuito, no enchufe el calefactor a un circuito compartido
con otros electrodomésticos.
11.
PRECAUCIÓN:
Es normal que el enchufe esté caliente al tacto; sin
embargo, una mala conexión entre la toma de CA (receptáculo) y el
enchufe puede provocar sobrecalentamiento y deformación del enchufe.
Póngase en contacto con un electricista calificado para reemplazar el
tomacorriente flojo o gastado.

2
¡GUARDE ESTAS INSTRUCCIONES!
12. Para desconectar, ponga el control en OFF y luego desenchufe de la toma.
No tire del cable.
13. No permita que objetos extraños entren en ninguna ranura de ventilación o
escape de aire, ya que esto puede provocar una descarga eléctrica o un
incendio, o dañar el aparato.
14. Para evitar un posible incendio, no bloquee las entradas de aire o de
escape de ninguna manera. No utilizar sobre superficies blandas, como
una cama, donde las aberturas puedan bloquearse.
15. Un calefactor tiene partes calientes o que pueden echar chispas. No lo
utilice en áreas donde pueda entrar en contacto con gasolina, pintura o
líquidos inflamables.
16. Utilizar sólo como se describe en este manual. Cualquier otro uso no
indicado por el fabricante puede causar un incendio, descargas eléctricas o
lesiones personales.
17.
PRECAUCIÓN:
Siempre conecte los calefactores directamente a la toma
de pared/receptáculo. No se debe usar un cable de extensión o una toma
de alimentación recargable (regleta).
18. La salida de este calefactor puede variar y su temperatura puede llegar a
ser lo suficientemente alta como para quemar la piel expuesta. No se
recomienda el uso de este aparato a personas con sensibilidad reducida al
calor o vulnerabilidad a quemaduras.
19. Se debe seguir las normas y regulaciones locales al eliminar el aceite
contenido dentro del aparato.
20.
Advertencia:
No cubra el calefactor para evitar sobrecalentamiento.
21.
ADVERTENCIA:
Para evitar descargas eléctricas, asegúrese de que el
ancho de las patas del enchufe encajen bien en la toma de corriente e
inserte completamente.
22.

3
PIEZAS Y CARACTERÍSTICAS
INSTRUCCIONES DE USO
Ɣ Antes de encender:
1. Compruebe que el cable de alimentación esté en buenas condiciones.
2. El producto utiliza una fuente de alimentación de CA 120V 60Hz. Confirme si la corriente nominal
de la toma cumple con los requisitos locales de seguridad y puesta a tierra, de lo contrario, reemplace
con el zócalo correcto.
Ɣ Coloque el aparato sobre una superficie plana.
Una superficie desigual puede hacer que el calefactor no funcione al encenderse; al menos la
superficie por debajo de la base del aparato debe ser plana.
Ɣ Interruptor de encendido
Gire la perilla de potencia para seleccionar entre 4 funciones: Ventilador: Bajo, Alto; Calefacción: Bajo
(900W), Alto 1500W.
Ɣ Apagar
A. Gire la perilla de ajuste de poder a la posición OFF.
B. B. Retire el enchufe de la toma, y guarde el calefactor una vez que se haya enfriado.
Ɣ Protección de Seguridad
1. Protección contra sobrecalentamiento: Este calefactor está equipado con un Sistema de Protección
contra Sobrecalentamiento, que hace que el aparato se apague si se sobrecalienta debido a
condiciones anormales. Si esto ocurre, apague ("OFF"), desconecte, y examine el aparato quitando
cualquier objeto que se encuentre sobre o adyacente al calefactor. Deje enfriar por unos minutos,
vuelva a enchufar, y continúe con el uso normal.
2. Protección contra vuelcos: El "botón" blanco en la parte inferior del producto es un interruptor de
vuelco. Cuando el producto se sienta en posición vertical, el botón se presiona y la unidad funciona-
rá. Si el producto se cae, el botón se suelta y el producto se apagará.
Indicador de encendido
Selección de potencia
Rejilla de
seguridad
OFF
(Ventilador)
BAJO
(Ventilador)
ALTO
(Calefacción)
BAJO
(Calefacción)
ALTO
No cubrir

4
Este calefactor posee características adicionales:
x Mango de transporte - permite un fácil transporte de una habitación a
otra.
Si su calentador no funciona, siga estas instrucciones:
x Asegúrese de que el interruptor de circuito o fusible esté funcionando
adecuadamente.
Asegúrese de que el calentador esté enchufado y que la toma de corriente
funciona correctamente.
Compruebe si hay alguna obstrucción. Si encuentra alguna obstrucción,
coloque el calentador en "OFF". Desenchufe el calentador y espere unos
minutos para que se enfríe. Retire la obstrucción cuidadosamente. Volver a
enchufar y encender, siempre siguiendo las INSTRUCCIONES DE USO.
OBSERVACIÓN: SI TIENE PROBLEMAS CON SU PRODUCTO, POR
FAVOR, CONSULTE LA INFORMACIÓN DE GARANTÍA PARA OBTENER
INSTRUCCIONES. NO INTENTE ABRIR O REPARAR ESTE PRODUCTO
USTED MISMO. ESTO PUEDE ANULAR LA GARANTÍA Y PODRÍA CAUSAR
DAÑOS AL APARATO O LESIONES PERSONALES. SI EL PROBLEMA
PERSISTE, CONTÁCTENOS AL NÚMERO EN LA PÁGINA SIGUIEN
TE
SOBRE SERVICIO Y SOPORTE.
Se recomienda limpiar el calefactor al menos una vez durante la temporada de
uso para funcionamiento óptimo. SIEMPRE APAGAR Y DESCONECTAR
ANTES DE LIMPIAR.
TES DE LIMPIAR. Asegúrese de guardar la caja para almacenarlo
cuando no se use.
x Coloque el calefactor en "OFF", desenchúfelo y espere a que se enfríe.
Utilice un paño seco para limpiar sólo las superficies externas.
No utilice productos de limpieza o detergentes.
No sumergir en agua.
Coloque el calentador en su caja original y guárdelo en un lugar fresco
y seco.
x
x
x
x
Modelo: PSF10M6ASB
Voltaje: 120V, 60Hz
Corriente: Consumo continuo máximo: 12,5 Amps.
Salida: 5200 BTUs
Potencia: BAJO = 900 Watts, ALTO = 1500 Watts
CARACTERÍSTICAS ADICIONALES
SOLUCIÓN DE PROBLEMAS
LIMPIEZA Y MANTENIMIENTO
ESPECIFICACIONES

5
SERVICIO Y SOPORTE
En el caso de reclamo de garantía o si se requiere servicio para este
ventilador, póngase en contacto con el
número gratuito: 1-866-646-4332
Por dudas o comentarios, por favor escriba a:
Midea America Corp
5 Sylvan Way, Suite 100
Parsippany, NJ 07054
(ENGRAPAR RECIBO AQUÍ)
OBSERVACIÓN: PARA TODO RECLAMO DE GARANTÍA
ES NECESARIO PRESENTAR RECIBO DE COMPRA
IMPRESO EN CHINA
Para su registro, engrape su recibo de compra a este manual y registre lo
siguiente:
FECHA DE COMPRA:
LUGAR DE COMPRA:

6
GARANTÍA LIMITADA DE UN (1) AÑO
Por favor, lea todas las instrucciones antes de usar este producto.
Midea America Corporation garantiza de forma limitada al comprador original que cada
ventilador calefactor nuevo estará exento de defectos materiales y de fabricación por un
período de un (1) año a partir de la fecha de la compra original. Esta garantía de un (1) año
se limita a los elementos calefactores, al motor, y a la placa de circuito eléctrico.
En el caso de mal funcionamiento o avería de su ventilador calefactor, Ud. podrá simple-
mente enviar el producto a portes pagados junto con una PRUEBA DE COMPRA, dentro
del período de garantía de un (1) año, a Midea America Corporation. Midea America
Corporation se reserva el derecho de inspeccionar el reclamo de partes defectuosas para
determinar
si el defecto o fallo está cubierto dentro de esta garantía. Midea America Corporation
deberá, en un plazo de sesenta (60) días siguientes al recibo del producto, reparar y/o
reemplazar la parte o partes defectuosas según su criterio de forma gratuita. Esta garantía
sólo cubre defectos derivados del uso normal del producto. Midea America Corporation no
asume ninguna responsabilidad si el Ventilador Calefactor fallase dentro del período de
garantía por razones de:
Midea America Corporation no otorgará más garantías o representaciones, expresas o
implícitas, excepto las contenidas en el presente documento. Ningún representante o
vendedor está autorizado a asumir cualquier otra responsabilidad relacionada con el
Ventilador Calefactor. La duración de la garantía implícita concedida bajo la ley del
Estado, incluidas las garantías de comerciabilidad y adecuación para un propósito
particular, están limitadas en duración si la duración de la garantía expresa lo otorgara a
continuación. Midea América Corporation no será responsable en caso alguno por daños
directos, indirectos, especiales o consecuentes.
Algunos estados no permiten limitaciones a la duración de una garantía implícita, y/o las
limitaciones o exclusiones anteriores pueden no aplicarse en su caso. Esta garantía le
otorga derechos legales específicos, y usted puede tener otros derechos que varían de
estado a estado.
Uso inadecuado, negligencia, daños físicos o accidentales.
Falta de mantenimiento (ver instrucciones para el mantenimiento adecuado).
Reparación por una parte no autorizada durante el periodo de garantía.
Daños causados por conexión a un voltaje inapropiado (ver la etiqueta de especifi-
caciones en el calefactor).

