BAUMR-AG SAWMITBMRA20SR 210mm Sliding Compound Mitre Drop User Manual

User Manual

[Revision 2.0 December 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

SBR-210 8” Mitre Saw

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

General Safety Instructions

WARNING! READ ALL SAFETY WARNINGS INSTRUCTIONS, ILLUSTRATIONS AND SPECIFICATIONS PROVIDED WITH THIS POWER

TOOL. FAILURE TO FOLLOW THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS

INJURY. THE TERM "POWER TOOL" IN THE WARNINGS REFERS TO YOUR MAINS-OPERATED (CORDED) POWER TOOL OR BATTERY-

OPERATED (CORDLESS) POWER TOOL.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

Child Choking Hazard!

• WARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

Work Area Safety

• Keep work area clean and well lit. Cluttered and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the

risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

• Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Always keep proper footing and balance. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these

devices can reduce dust related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

Power Tool Use and Care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power

tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories, and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of

power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended

could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool

is maintained.

Safety Regulations Concerning Mitre Saw

• Mitre saws are intended to cut wood or wood-like products, they cannot be used with abrasive cut-off wheels for cutting ferrous material such as

bars, rods, studs, etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive cutting will burn the lower guard,

the kerf insert and other plastic parts.

• Use clamps to support the workpiece whenever possible. If supporting the workpiece by hand, you must always keep your hand at least 100mm

from either side of the sawblade. Do not use this saw to cut pieces that are too small to be securely clamped or held by hand. If your hand is

placed too close to the saw blade, there is an increased risk of injury from blade contact.

• The workpiece must be stationary and clamped or held against both the fence and the table. Do not feed the workpiece into the blade or cut

“freehand” in any way. Unrestrained or moving workpieces could be thrown at high speeds, causing injury.

• Push the saw through the workpiece. Do not pull the saw through the workpiece. To make a cut, raise the saw head and pull it out over the

workpiece without cutting, start the motor, press the saw head down and push the saw through the workpiece. Cutting on the pull stroke is likely

to cause the saw blade to climb on top of the workpiece and violently throw the blade assembly towards the operator.

• Never cross your hand over the intended line of cutting either in front or behind the saw blade. Supporting the workpiece “cross handed” i.e.,

holding the workpiece to the right of the saw blade with your left hand or vice versa is very dangerous.

• Do not reach behind the fence with either hand closer than 100mm from either side of the saw blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity of the spinning saw blade to your hand may not be obvious and you may be seriously injured.

• Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece, fence, and table along the line of the cut. Bent or warped workpieces can twist or shift and

may cause binding on the spinning saw blade while cutting. There should be no nails or foreign objects in the workpiece.

• Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of wood or other

objects that contact the revolving blade can be thrown with high speed.

• Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately clamped or braced and may bind on the blade or shift

during cutting.

• Ensure the mitre saw is mounted or placed on a level, firm work surface before use. A level and firm work surface reduces the risk of the mitre

saw becoming unstable.

• Plan your work. Every time you change the bevel or mitre angle setting, make sure the adjustable fence is set correctly to support the workpiece

and will not interfere with the blade or the guarding system. Without turning the tool ²ON² and with no workpiece on the table, move the saw blade

through a complete simulated cut to assure there will be no interference or danger of cutting the fence.

• Provide adequate support such as table extensions, saw horses, etc. for a workpiece that is wider or longer than the table top. Workpieces longer

or wider than the mitre saw table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the lower guard or be thrown by

the spinning blade.

• Do not use another person as a substitute for a table extension or as additional support. Unstable support for the workpiece can cause the blade

to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

• The cut-off piece must not be jammed or pressed by any means against the spinning sawblade. If confined, i.e., using length stops, the cut-off

piece could get wedged against the blade and thrown violently.

• Always use a clamp or a fixture designed to properly support round material such as rods or tubing. Rods tend to roll while being cut, causing the

blade to ²bite² and pull the work with your hand into the blade.

• Let the blade reach full speed before contacting the workpiece. This will reduce the risk of the workpiece being thrown.

• If the workpiece or blade becomes jammed, turn the mitre saw off. Wait for all moving parts to stop and disconnect the plug from the power

source and/or remove the battery pack. Then work to free the jammed material. Continued sawing with a jammed workpiece could cause loss of

control or damage to the mitre saw.

• After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

• Hold the handle firmly when making an incomplete cut or when releasing the switch before the saw head is completely in the down position. The

braking action of the saw may cause the saw head to be suddenly pulled downward, causing a risk of injury.

Residual Risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in

connection with the equipment’s construction and layout:

• Lung damage if no suitable protective dust mask is used.

• Damage to hearing if no suitable ear protection is used.

• Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

WARNING! THIS PRODUCT PRODUCES AN ELECTROMAGNETIC FIELD DURING OPERATION! THIS FIELD MAY UNDER SOME

CIRCUMSTANCES INTERFERE WITH ACTIVE OR PASSIVE MEDICAL IMPLANTS! TO REDUCE THE RISK OF SERIOUS OR FATAL

INJURY, WE RECOMMEND PERSONS WITH MEDICAL IMPLANTS TO CONSULT THEIR DOCTOR AND THE MEDICAL IMPLANT

MANUFACTURER BEFORE OPERATING THIS PRODUCT!

Safety Rules for Laser Lights

The laser light/laser radiation used in the system is Class 2 with maximum1mWand 650nm wavelengths. These lasers do not normally present an

optical hazard, although staring at the beam may cause flash blindness.

WARNING! DO NOT STARE DIRECTLY AT THE LASER BEAM. A HAZARD MAY EXIST IF YOU DELIBERATELY STARE INTO THE BEAM,

PLEASE OBSERVE ALL SAFETY RULES AS FOLLOWS:

• The laser shall be used and maintained in accordance with the manufacturer’s instructions.

• Never aim the beam at any person or an object other than the workpiece.

• The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person for longer

than 0.25s.

• Always ensure the laser beam is aimed at a sturdy workpiece without reflective surfaces. i.e., wood or rough coated surfaces are acceptable.

Bright shiny reflective sheet steel or the like is not suitable for laser use as the reflective surface could direct the beam back at the operator.

• Do not change the laser light assembly with a different type. Repairs must be carried out by the laser manufacturer or an authorised agent.

CAUTION! USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

Intended Use

This mitre saw is intended for cutting wood and analogue materials, it is suitable for straight and curved cuts having Mitre angles of up to 45°. The

saw is not designed for cutting firewood. Do not use machines, tools, and accessories for additional applications (see manufacturer’s instructions)

for works other than those for which they are designed for. All other applications are expressly ruled out.

Not Intended Use

• If not intended use, the risk of fire, electric shock, and personal injury may be increased.

• The provisions contained in this guarantee are not intended to limit, modify, take away from, disclaim or exclude any statutory guarantee set forth

in any applicable provincial or federal legislation.

Noise Information

The noise emission and its uncertainty measured in accordance with EN62841-1. Wear hearing protection! The noise figures quoted are emission

levels and actual use of the power tool can differ from the declared are not necessarily safe working levels.

Vibration

WARNING! THE VIBRATION EMISSION DURING ACTUAL USE OF THE POWER TOOL CAN DIFFER THE TOTAL VALUE OF DEPENDING

ON THE DIFFERENT WAYS IN WHICH THE TOOL IS USED; AND AVOID VIBRATION RISK SUGGESTION:

• Wear glove during operation

• Limit operating time and shorten

Vibration and Noise Reduction

To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear

personal protective equipment.

Take the following points into account to minimize the vibration and noise exposure risks:

• Only use the product as intended by its design and these instructions.

• Ensure that the product is in good condition and well maintained.

• Use correct application tools for the product and ensure they in good condition.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

• Keep tight grip on the handles/grip surface.

• Maintain this product in accordance with these instructions and keep it well lubricated (where appropriate).

• Plan your work schedule to spread any high vibration tool use across a number of days

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 7

Parts Identification ..................................................................................................................................... 10

Assembly ..................................................................................................................................................... 11

Dust Extraction Port .................................................................................................................................................. 11

Mounting Holes ......................................................................................................................................................... 11

Workpiece Clamp ..................................................................................................................................................... 11

Table Extension ........................................................................................................................................................ 11

Operation ..................................................................................................................................................... 12

Release Knob ........................................................................................................................................................... 12

Transportation ........................................................................................................................................................... 12

Mitre Table Locks ..................................................................................................................................................... 12

Bevel Lock ................................................................................................................................................................ 12

Spindle Lock Button .................................................................................................................................................. 12

Rotating Lower Blade Guard .................................................................................................................................... 12

Turning ON and OFF ................................................................................................................................................ 13

Laser ON/OFF .......................................................................................................................................................... 13

Setting the Table Square with the Blade .................................................................................................................. 13

Setting the Fence Square with the Table ................................................................................................................. 14

Changing A Blade ..................................................................................................................................................... 14

Cross Cut .................................................................................................................................................................. 15

Bevel Cut .................................................................................................................................................................. 15

Compound Mitre Cut ................................................................................................................................................. 16

Setting the Cutting Depth ......................................................................................................................................... 16

Maintenance ................................................................................................................................................ 17

General Maintenance ............................................................................................................................................... 17

General Inspection .................................................................................................................................................... 17

Servicing the Tool ..................................................................................................................................................... 17

Specifications ............................................................................................................................................. 18

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Parts Identification

No. Name No. Name No. Name

1

Laser light

12

Bevel lock

23

Slide bars

2

Laser light ON/OFF switch

13

Bevel scale

24

Slide lock

3 Saw arm 14 Fence 25 Trenching depth adjustment screw

4 Release knob 15 6mm Hex key 26 Trenching stop

5 Operating handle 16 Mitre table 27 Trenching depth lock nut

6 Upper fixed blade guard 17 Mitre scale 28 45°Bevel adjustment screw

7

G clamp

18

Table insert

29

0° Bevel adjustment screw

8

Rotating blade guard

19

Switch trigger

30

Switch lock

9

Guard retraction arm

20

Mitre lock knob

31

Extension base (x2)

10 Blade bolt cover 21 Mitre latch

11 Dust bag 22 Spindle lock

5

9

11

23

1

8

10

6

18

16

17

31

28

13

19

15

7

14

3

22

2

30

24

4

26

27

25

29

12

21

20

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Assembly

WARNING! TO PREVENT THE ACCIDENTAL STARTING THAT COULD CAUSE POSSIBLE

SEROUS PERSONAL INJURY, ALWAYS ASSEMBLE ALL PARTS TO YOU SAW BEFORE

CONNECTING IT TO THE POWER SUPPLY. THE SAW SHOULD NEVER BE CONNECTED TO A POWER

SUPPLY WHEN YOU ARE ASSEMBLING PARTS, ADJUSTING, INSTALLING OR REMOVING BLADES, OR

WHEN NOT IN USE.

Dust Extraction Port

•

To reduce build-up of saw dust and maintain top efficiency of cutting, the saw dust collection can be

achieved by clipping a dust bag on the dust extraction port.

•

A dust bag is provided for use on you mitre saw. To install it, simply fit the dust bag over the extraction port

on the upper blade guard.

•

To empty the dust bag, remove it from the dust exhaust port, open the dust by unzipping the slide fastener.

NOTE: to ensure optimal dust collecting, empty the dust bag when it becomes filled to approximately 2/3 of its

capacity.

Mounting Holes

Before use, the saw can be fixed to a firm, level surface with the 4 mounting bolts (Not supplied). Four holes are

provided in the base of the saw to enable it to be fixed to a bench, or other supporting surface.

To mount the saw, process as follows:

1. Locate and mark where the saw is to be mounted.

2. Drill 4 holes through the surface.

3. Place the mitre saw on the surface aligning holes in base when holes drilled in the surface. Install holes,

washers and nuts.

CAUTION! MAKE SURE THAT THE MOUNTING SURFACE IS NOT WARPED AS AN UNEVEN

SURFACE CAN CAUSE BINDING AND INACCURATE SAWING.

Workpiece Clamp

When cutting a workpiece, the boards should always be clamped down with the G Clamp.

Table Extension

For supporting long workpiece, fix the Side support base and adjust the length to suit the long work pieces. Then

tighten the screw of base.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Operation

IMPORTANT! BE SURE THE SUPPLY IS THE SAME AS THE VOLTAGE GIVEN ON THE RATING

PLATE. REMOVE THE MAINS PLUG BEFORE CARRYING OUT ANY ADJUSTMENT OR

SERVICING.

Release Knob

When boxed or during storage, transportation, the saw head is locked in the down position.

1. To release the head ready for operation, apply downward pressure on the saw arm and pull out the release

knob (4), and rotate the knob to unlock the saw head.

2. The head will be raised gently to upper position. The saw must never be used with the release knob locking

the head down.

Transportation

1. When transporting the saw with fixed locations, make sure that the saw head is locked in the lower position.

2. The rotary table locking knob, the bevel lock knob and slide lock must all be securely tightened.

3. The saw is switched off and the plug is removed from the power point.

4. Only lift the saw by the operating handle (5) or outer castings. Do not lift the saw using the guards.

For locking the saw head in the down position. Apply downward pressure on the saw arm and pull out the

release knob (4), rotate the knob to lock the saw head. The head will be locked in down position.

Mitre Table Locks

•

The mitre table locks (20) are used to lock the table at the desired mitre angle.

•

The mitre saw cuts from 0° to 45° both left and right. To adjust the mitre angle, loosen the mitre table locks

(20) (21) and rotate the mitre table to the desired position.

•

The mitre table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick setting of common mitre

angles.

Bevel Lock

The bevel lock (12) is used to set the blade at the desired bevel angle. The mitre saw bevel cuts from 0° to 45°

to the left. To adjust the bevel angle, loosen the bevel lock and adjust the saw arm to the desired bevel angle.

Spindle Lock Button

The spindle lock button (22) prevents the blade in the saw from rotating. Depress and hold the spindle lock

button while installing, changing, or removing the blade.

Rotating Lower Blade Guard

The rotating lower blade guard (8) provides protection from both sides of the blade. It retracts over the upper

blade guard (6) as the saw is lowered into the workpiece.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Turning ON and OFF

1. To turn the saw ON, press switch lock (30) to left and depress the ON/OFF trigger switch (19)

2. To turn the saw OFF release the ON/OFF trigger switch (19).

Laser ON/OFF

1. Switch ON/OFF the laser lights with the ON/OFF switch (2).

2. Press laser switch at the I position, place to ON, press at 0, then place to OFF.

Setting the Table Square with the Blade

1. Make sure that the electrical plug is removed from the power point.

2. ush the saw arm (3) down to its lowest position and engage the release knob (4) to hold the saw arm in the

transport position.

3. Loosen the mitre locks (20) and lifting up the mitre latch (21).

4. Rotate the table (16) until the pointer is positioned at 0°.

5. Release mitre latch (21) and tighten the mitre locks (20).

6. Loosen the bevel lock (12) and set the saw arm (3) at 0°bevel (the blade at 90°to the mitre table). Tighten

the bevel lock (12).

7. Place a set square against the table (16) and the flat part of the blade.

8. Rotate the blade by hand and check the blade-to-table alignment at several points.

9. The edge of the set square and the sawblade should be parallel.

10. If the sawblade angles away from the set square, adjust as follows.

11. Use a 10mm wrench or adjustable wrench to loosen the lock nut securing the 0° bevel adjustment screw

(29). Also, loosen the bevel lock (12).

12. Adjust the 0° bevel adjustment screw (29) using a 4mm hex key to bring the sawblade into alignment with

the square.

13. Loosen the Phillips head screw holding the pointer of the bevel scale (13) and adjust the position of the

pointer so that it accurately indicates zero on the scale. Retighten the screw.

14. Retighten the bevel lock (12) and the lock nut securing the 0° bevel adjustment screw (29).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Setting the Fence Square with the Table

1. Make sure that the electrical plug is removed from the power point.

2. Push the saw arm (3) down to its lowest position and engage the release knob (4) to hold the saw arm in the

transport position.

3. Loosen the mitre locks (20) and lifting up the mitre latch (21).

4. Rotate the table (16) until the pointer is positioned at 0°.

5. Release mitre latch (21) and tighten the mitre locks (20).

6. Using a 5mm hex key, loosen the two screws securing the fence (14) to the base.

7. Place a square against the fence (14) and alongside the blade.

8. Adjust the fence (14) until it is square with the blade.

9. Tighten the screws securing the fence (14).

10. Loosen the Phillips head screw holding the pointer of the mitre scale (17) and adjust it so that it accurately

indicates the zero position on the mitre scale.

11. Retighten the screw securing the mitre scale pointer.

Changing A Blade

NOTE: It is recommended to use a pair of stout gloves for this.

1. Make sure that the electrical plug is removed from the power point.

2. Pushdown on the operating handle (5) and pull the release knob (4) to disengage the saw arm (3).

3. Raise the saw arm (3) to its highest position.

4. Loosen the cover plate screw with a Phillips screwdriver.

5. Pull the rotating blade guard (8) and turn the rotating blade guard (8) is positioned over the upper fixed blade

guard (6), it is possible to access the blade bolt.

6. Hold the rotating guard (8) up and press the spindle lock button (22). Rotate the blade until the spindle locks.

7. Use the 6mm hex key provided to loosen and remove the blade bolt. (Loosen in a clockwise direction as the

blade screw has a left-hand thread).

8. Remove the flat washer, outer blade flange and the blade. Clean any saw dust and debris from the arbor

and saw blade.

9. Wipe a drop of oil onto the inner blade flange and the outer blade flange where they contact the blade.

10. Fit the new blade onto the spindle taking care that the inner blade flange sits behind the blade.

11. Replace the outer blade flange.

12. Depress the spindle lock button (22) and replace the flat washer and blade bolt.

13. Use the 6mm hex key to tighten the blade bolt securely (tighten in an anti-clockwise direction).

14. Lower and hold the rotating lower blade guard (8) and blade bolt cover (10) in position, replace and tighten

the fixing screw to secure the blade bolt cover in position.

15. Check that the blade guard operates correctly and covers the blade as the saw arm is lowered.

16. Connect the saw to the power supply and run the blade to make certain that it is operating correctly.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Cross Cut

If possible, always use a clamping device such as a G clamp to secure your workpiece. When cutting your

workpiece, keep your hands well away from the blade area. Do not remove a cut-off piece on the right-hand side

of the blade using your left hand.

A crosscut is made by cutting across the grain of the workpiece. A 90° crosscut is made with the mitre table set

at 0°. Mitre crosscuts are made with the table set at some angle other than zero.

1. Pull on the release knob (4) and lift the saw arm (3) to its full height.

2. Loosen the mitre locks (20) and lifting up the mitre latch (21).

3. Rotate the mitre table (16) until the pointer aligns with the desired angle.

4. Release mitre latch (21) and re-tighten the mitre locks (20).

5. Place the workpiece flat on the table with one edge securely against the fence (14). If the board is warped,

place the convex side against the fence (14). If the concave side is placed against the fence, the board could

break and jam the blade.

6. When cutting long pieces of timber, support the opposite end of the timber with side support bars, a roller

stand or a work surface that is level with the saw table.

7. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems

such as a clamp interfering with the cutting action.

8. Hold the operating handle (5) firmly, squeeze switch lock (30) and the switch trigger (19). Allow the blade to

reach maximum speed and slowly lower the blade into and through the workpiece.

9. Release the switch trigger (19) and allow the sawblade to stop rotating before raising the blade out of the

workpiece. Wait until the blade stops before removing the workpiece.

Bevel Cut

If possible, always use a clamping device such as a G clamp on the right of mitre table to secure your

workpiece. When cutting your workpiece, keep your hands well away from the blade area. Do not remove a cut-

off piece on the right-hand side of the blade using your left hand.

A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the fence and mitre

table. The mitre table is set at the zero-degree position and the blade set at an angle between 0°and 45°.

1. Pull on the release knob (4) and lift the saw arm to its full height.

2. Loosen the mitre locks (20) and lifting up the mitre latch (21).

3. Rotate the mitre table (16) until the pointer aligns with zero on the mitre scale (17).

4. Release mitre latch (21) and retighten the mitre locks (20).

5. Loosen the bevel lock (12) and move the saw arm (3) to the left to the desired bevel angle (between 0°and

45°). Tighten the bevel lock (12).

6. Place the workpiece flat on the table with one edge securely against the fence (14). If the board is warped,

place the convex side against the fence. If the concave side is placed against the fence, the board could

break and jam the blade.

7. When cutting long pieces of timber, support the opposite end of the timber with side support bars, a roller

stand or a work surface that is level with the saw table.

8. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems

such as a clamp interfering with the cutting action.

9. Hold the operating handle (5) firmly, squeeze switch lock (30) and the switch trigger (19). Allow the blade to

reach maximum speed, and slowly lower the blade into and through the workpiece.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

10. Release the switch trigger (19) and allow the saw blade to stop rotating before raising the blade out of the

workpiece. Wait until the blade stops before removing the workpiece.

Compound Mitre Cut

If possible, always use a clamping device such as a G clamp on the right of mitre table to secure your

workpiece. When cutting your workpiece, keep your hands well away from the blade area. Do not remove a cut-

off piece on the right-hand side of the blade using your left hand.

A compound mitre cut involves using a mitre angle and a bevel angle at the same time. It is used in making

picture frames, to cut mouldings, making boxes with sloping sides and for roof framing. Always make a test cut

on a piece of scrap wood before cutting into the good material.

1. Pull on the release knob (4) and lift the saw arm to its full height.

2. Loosen the mitre locks (20) and lift up the mitre latch (21).

3. Rotate the mitre table (16) until the pointer aligns with the desired angle on the mitre scale (17).

4. Release mitre latch (21) and retighten the mitre locks (20).

5. Loosen the bevel lock (10) and move the saw arm (3) to the left to the desired bevel angle (between 0°and

45°). Tighten the bevel lock (12).

6. Place the workpiece flat on the table with one edge securely against the fence (14). If the board is warped,

place the convex side against the fence. If the concave side is placed against the fence, the board could

break and jam the blade.

7. When cutting long pieces of timber, support the opposite end of the timber with the side support bars, a roller

stand or a work surface that is level with the saw table.

8. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems

such as a clamp interfering with the cutting action.

9. Hold the operating handle (5) and firmly, squeeze switch lock (30) and the switch trigger (19). Allow the

blade to reach maximum speed, and slowly lower the blade into and through the workpiece.

10. Release the switch trigger (19) and allow the saw blade to stop rotating before raising the blade out of the

workpiece. Wait until the blade stops before removing the workpiece.

To Slide Cut-Wide Boards

To slide cut-wide boards, Unlock the slide lock knob (24) and allow the cutting head assembly to move freely.

Setting the Cutting Depth

The depth of cut can be pre-set for even and repetitive shallow cuts.

1. Slide Trenching stop (26) towards the front position.

2. Loosen the Trenching depth lock nut (27) to free the Trenching depth adjustment screw (25), turn the screw

until the cutting head down until the teeth of the blade are at the desired depth.

3. While holding the upper arm in that position, tighten the lock nut (27) to secure the trenching depth

adjustment screw (25).

4. Recheck the blade depth by moving the cutting head front to back through the full motion of typical cut along

the control arm.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Maintenance

WARNING! REMOVE THE PLUG FROM THE SOCKET BEFORE CARRYING OUT ANY

ADJUSTMENT, SERVICING, OR MAINTENANCE.

General Maintenance

•

When all the adjustments, settings or maintenance have been done, make sure that all keys and wrenches

have been removed and that all screws, bolts, and other fittings are securely tightened.

•

Keep the tool's air vents unclogged and clean at all times. Occasionally you may see sparks through the

ventilation slots. This is normal and will not damage your power tool.

•

Regularly check to see if any dust or foreign matter has entered the grills near the motor and around the

trigger switch. Use a soft brush to remove any accumulated dust.

•

Wear safety glasses to protect your eyes whilst cleaning.

•

If the body of the saw needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used but

nothing like alcohol, petrol, or other cleaning agent.

•

Never use caustic agents to clean plastic parts.

CAUTION: WATER MUST NEVER COME INTO CONTACT WITH THE SAW.

•

Store the tool and accessories in a secure place. In this way, you will always have all the parts on hand.

General Inspection

•

Regularly check that all the fixing screws are tight. They may vibrate loose over time. Check especially the

outer flange. If there is vibration, screws can loosen with time.

•

Regularly check the device’s power cable and all extension cables used for damage. If the supply cord

needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an

authorized service centre to avoid a safety hazard. Replace damaged extension cables.

•

If the carbon brushes need to be replaced, have this done by a qualified repair person (always replace the

two brushes at the same time).

Servicing the Tool

•

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by

unqualified personnel could result in a risk of injury.

•

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section

of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of

electric shock or injury.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

SBR-210 8” Mitre Saw

Specifications

Rated power 1500W

No-load speed 4500 rpm

Blade diameter 210mm

Blade teeth 24T

Swivel range ±45°

Bevel tilt range 0°-45° to the left

Cutting Capacity

0°/90°: 305 x 70mm

0°/45°: 215 × 70mm

Laser Class 2

Input voltage 220-240V / 50Hz

Power Plug Australian Standard

Minimal Assembly required

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG SAWMITBMRA20SR 210mm Sliding Compound Mitre Drop Saw

Product's Documents

Product manual

Specifications

BAUMR-AG SAWMITBMRA20SR Questions and Answers