Sealey MS900PS 170mm 1300W/230V Variable Speed User Manual

Ø170MM VARIABLE SPEED SANDER/POLISHER

1300W

MODEL NO: MS900PS

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1. ELECTRICAL SAFETY

 WARNING! It is the user’s responsibility to check the following:

Check all electrical equipment and appliances to ensure that they are safe before using.

Inspect power supply leads, plugs and all electrical connections for wear and damage.

Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

8 DO NOT use worn or damaged cables, plugs or connectors.

9  Ensurethatanyfaultyitemisrepairedorisreplacedimmediatelybyaqualiedelectrician.

9  Ifthecableorplugisdamagedduringuse,switcho󰀨theelectricitysupplyandremovefromuse.

 Ensurethatrepairsarecarriedoutbyaqualiedelectrician.

9  SealeyrecommendthatanRCD(ResidualCurrentDevice)isusedwithallelectricalproducts.

Important:Ensurethatthevoltageratingontheappliancesuitsthepowersupplytobeusedandthattheplugisttedwiththe 

correct fuse.

8 DO NOT pull or carry the appliance by the power cable.

8 DO NOT pull the plug from the socket by the cable.

1.2. GENERAL SAFETY

 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this

equipment.

 WARNING!Disconnectfrommainspowerbeforechangingaccessoriesorservicing.

9 Familiarise yourself with the application and limitations of the product, as well as the specific potential hazards peculiar to the polisher.

 WARNING! Disconnectfromthemainspowerandensurethediscisatacompletestandstillbeforechangingaccessories,servicing

or performing any maintenance.

9  Maintainthepolisher/sanderingoodcondition(useanauthorisedserviceagent).

9  Replaceorrepairdamagedparts.Usegenuinepartsonly.Non-authorisedpartsmaybedangerousandwillinvalidatethewarranty.

 WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts. A guard

or any other part that is damaged must be repaired/replaced before the tool is next used.

9 Locate polisher/sander in a suitable working area, keep area clean and tidy and free from unrelated materials. Ensure there is

adequate lighting.

9 Keep the polisher/sander clean for best and safest performance.

9  Beforeeachusecheckabrasiveattachmentsforcondition.Ifwornordamagedreplaceimmediately.

9 Ensure there are no flammable or combustible materials near the work area.

 WARNING!Wearapprovedeyesafetyprotection,eardefendersand,ifdustisgenerated,respiratoryprotection.

9  Maintaincorrectbalanceandfooting.Ensuretheoorisnotslipperyandwearnon-slipshoes.

9  Removeillttingclothing.Removeties,watches,rings,andotherloosejewellery,andcontainand/ortiebacklonghair.

9 Keep children and unauthorised persons away from the working area.

9  Securenon-stableworkpiecewithaclamp,viceorotheradequateholdingdevice.

9  Removeadjustingkeysandwrenchesfromthemachineanditsvicinitybeforeturningiton.

8 DO NOT use equipment for any purpose other than that for which it is designed.

8 DO NOToperatethepolisher/sanderifanypartsaredamagedormissingasthismaycausefailureorpossiblepersonalinjury.

 WARNING! DO NOT sand any materials containing asbestos.

8 DO NOTswitchthepolisher/sanderonwhilsttheheadisincontactwiththeworkpieceandavoidunintentionalstarting.

8 DO NOT get the polisher/sander wet or use in damp or wet locations or areas where there is condensation.

8 DO NOT allow untrained persons to operate the polisher/sander.

8 DO NOToperatethepolisher/sanderwhenyouaretired,undertheinuenceofalcohol,drugsorintoxicatingmedication.

8 DO NOTusethepolisher/sanderwherethereareammableliquids,solidsorgasessuchaspaintsolvents,etc.

8 DO NOTleavethepolisher/sanderoperatingunattended.

8 DO NOTcarrythepolisher/sanderwithyourngeronthepowerswitch.

8 DO NOTpullthecordtoremovetheplugfromthepowersupply.

9  Useaqualiedpersontolubricateandmaintainthepolisher/sander.

9 When not in use unplug from the mains power supply and store in a safe, dry, childproof area.

Refer to

instruction

manual

Wear eye

protection

MS900PS Issue:6 03/05/24

Original Language Version

Wear ear

protection

Wear

protective

gloves

Wear

a mask

LEAD PAINT WARNING!

 Paintoncecontainedleadasatraditionalingredient.Thedustfromtheremovalofsuchpaintistoxicifinhaledoringestedandmust,

 therefore,beavoided.Thefollowingactionmustbetakenbeforeusingthesanderonasurfacethatyoususpectmayhavecontainedlead

in the paint.

1. Usermustdeterminepotentialhazardrelatingtoageofpainttoberemoved.(Modernpaintsdonotcontainlead).

2. DANGER! Keepallpersonsandpetsawayfromtheworkarea.Thefollowingareparticularlyvulnerabletotheeffectsofleadpaintdust:

Expectant women, babies and children.

3. We recommend personal protection by using the following safety items:

a)PaintSprayRespirator

b)PECoatedHoodedCoverall

c)LatexGloves

4. Take adequate measures to contain the paint dust, flakes, and scrapings.

5. Continuetowearsafetyequipmentasin3above,andthoroughlycleanallareaswhentaskiscomplete.Ensurethatpaintwasteis 

disposed of in sealed bags or containers, according to local authority regulations.

2. INTRODUCTION

 Variablespeedcontrolsuitableforsandingandpolishing.Speedsvaryfrom1400-3000rpm.Alloybevelgearheadwithcomposite

motor housing. Supplied with Ø170mm backing pad and side handle.

3. SPECIFICATION

4. CONTENTS

 Refertog.1

1: Pol : Polisher Unit, 2: Side Handle, 3: Pad, 4: Spanner.

5. ASSEMBLY

 WARNING! Ensure unit is not plugged into mains before attempting any assembly.

5.1.  Attachthesidehandle(fig.1.2).Note:thereisamountingholeoneithersideandthetoptosuittheapplicationand/oroperator.

5.2. To attach the rubber pad:

 Threadtherubberpad(fig.1.3)onshaftandtightenusingspanner(fig.1.4)byholdingshaftsteadywithlockingbutton(fig.2).

5.3. To fit a sanding disc:

 Selectthegradeofselfadhesivesandingdiscrequired,peeloffthebackingandcentrallylocatethediscontotherubberpad.

5.4. To fit a polishing bonnet:

 Fitthepolishingbonnetoverthesecuredrubberpad,usingthepullcord,tightenthebonnetandtieabowtosecure,tuckthelooseends

of the bow neatly under the bonnet.

6. OPERATION

 WARNING! Ensure you read, understand and apply the safety instructions in Section 1.

6.1. Ensure the power control switch is NOT locked on before plugging into the mains.

6.2.  Holdthepolisherrmlywithonehandonthehandlegripandtheotheronthesidehandle.Toselecttherequiredspeedrotatethe

 speedselectorswitch(g.3.2)totherequiredspeed1to6.SpeedSettings:Rangefrom1000rpm-3000rpm.

Model No: MS900PS

Free Speed: 1400-3000rpm

Fuse Rating: 10A

Motor Power: 1300W

Nett Weight: 3.8kg

Noise power: 92dB(A)LwA

Pad Size: Ø170mm

Plug Type: 3-Pin

Power Supply Cable Length: 2m

Supply: 230V

Thread Size: M14 x 2mm

Vibration: 7.678m/s²

fig.

MS900PS Issue:6 03/05/24

Original Language Version

fig.

Locking

button

fig.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

arecyclingcentreanddisposedofinamannerwhichiscompatiblewiththeenvironment.Whentheproductbecomescompletely

unserviceableandrequiresdisposal,drainanyfluids(ifapplicable)intoapprovedcontainersanddisposeoftheproductandfluids

according to local regulations.

Note:Itisourpolicytocontinuallyimproveproductsandassuchwereservetherighttoalterdata,specificationsandcomponentparts

without prior notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.

WEEE REGULATIONS

DisposeofthisproductattheendofitsworkinglifeincompliancewiththeEUDirectiveonWasteElectricalandElectronicEquipment

(WEEE).Whentheproductisnolongerrequired,itmustbedisposedofinanenvironmentallyprotectiveway.Contactyourlocalsolid

waste authority for recycling information.

6.3.  Tostartthepolisherpressandholddownthesafetylockbutton(g.3.1)andsqueezethetrigger.Whenreleasingthetrigger,thesafety

 lockbuttonwillengage,preventingthepolisherfrombeinginadvertentlystarted.

 WARNING!Thehighspeedsettingsareintendedforsanding.Ifusedforpolishinganexcessiveamountofsurfacematerialmaybe

 removedorifpolishingattoohighaspeedthetoolwillburnthroughpaintwork.Forthisreasonitwillnotbenecessarytousethetool

 ataspeedsettingabove3(2000rpmnoload).

NOTE: Astherubbersupportdiscisexible,whensandingitshouldnotbeusedheadon,butatanangleofapproximately10to20

degrees.

6.4. Contact your Sealey stockist for details of compound heads and lambs wool bonnets.

7. MAINTENANCE.

 WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply.

7.1. Keep the machine clean and dry. DO NOTuseabrasivestocleantheunit.Ensureallexternalheadscrewsaretight.

7.2.  Cleanregularlybyblowingajetofcompressedairthroughsideventstoensuremotorventilationiskeptclear.

7.3.  WARNING!Wearapprovedsafetyeyeprotectionand,ifnecessary,respiratoryprotection.

NOTE.ThefollowingmaintenancemustonlybecarriedoutbyatechnicallyqualiedpersonoranauthorisedSealeyserviceagent

7.4.  Checkcarbonbrushesbyremovingeachsidescrew(g.4).Checktoseeifthebrushesarewornorcracked.Ifso,thebrushesmust

 bereplacedtoavoidsparkinganddamagetothearmature.Alwayschangebrushesasapair.Useonlygenuinesparepartsasthese

 arespecicallydesignedforthemachine.Failuretodosomaybedangerousandwillinvalidateyourwarranty.

7.5.  Aftereach500hoursofusereplacethegearheadgreasetopreventgearwearandpossibledrivefailure.

7.6.

WARNING! – RISK OF HAND ARM VIBRATION INJURY.

THIS TOOL MAY CAUSE HAND ARM VIBRATION SYNDROME IF ITS USE IS NOT MANAGED ADEQUATELY.

 ThistoolissubjecttothevibrationtestingsectionoftheMachineryDirective2006/42/EC.

This tool is to be operated in accordance with these instructions.

MEASURED VIBRATION EMISSION VALUE (a): 7.678m/s²

UNCERTAINTY VALUE (k): 1.5m/s²

Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend

that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.

 Ahealthandsafetyassessmentbytheuser(oremployer)willneedtobecarriedouttodeterminethesuitabledurationofuseforeach

tool.

NB: StatedVibrationEmissionvaluesaretype-testvaluesandareintendedtobetypical.

 Whilstinuse,theactualvaluewillvaryconsiderablyfromanddependonmanyfactors.

Such factors include; the operator, the task and the inserted tool or consumable.

NB:ensurethatthelengthofleaderhosesissufficienttoallowunrestricteduse,asthisalsohelpstoreducevibration.

The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm

Vibration Syndrome.

HEALTH SURVEILLANCE.

 Werecommendaprogrammeofhealthsurveillancetodetectearlysymptomsofvibrationinjurysothatmanagementprocedurescanbe

modified accordingly.

PERSONAL PROTECTIVE EQUIPMENT.

 Wearenotawareofanypersonalprotectiveequipment(PPE)thatprovidesprotectionagainstvibrationinjurythatmayresultfromthe

 uncontrolleduseofthistool.Werecommendasufficientsupplyofclothing(includinggloves)toenabletheoperatortoremainwarmand

 dryandmaintaingoodbloodcirculationinfingersetc.Pleasenotethatthemosteffectiveprotectionisprevention,pleaserefertothe

 CorrectUseandMaintenancesectionintheseinstructions.Guidancerelatingtothemanagementofhandarmvibrationcanbefoundon

the HSC website

 www.hse.gov.uk-Hand-ArmVibrationatWork.

MS900PS Issue:6 03/05/24

Original Language Version

PURCHASE HERE

Sealey MS900PS 170mm 1300W/230V Variable Speed Sander/Polisher

Product's Documents

User Manual

Specifications

Sealey MS900PS Questions and Answers