HELMET/GLOVE/BOOT DRYER STAND
MODEL NO: MS0815
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
Original Language Version
© Jack Sealey Limited
1. SAFETY
1.1. ELECTRICAL SAFETY FOR USE OF TRANSFORMER
9 Use only the supplied transformer or supplied 12V 1A USB cable for connecting the dryer stand assembly to the mains power supply.
Failure to observe this warning could result in injury and or re. The use of any other type of charger will invalidate the warranty.
8 DO NOT turn product on at the mains until the fan’s jack plug has been inserted into the dryer stand assembly.
WARNING! It is the user’s responsibility to read, understand and comply with the following instructions.
WARNING! You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices e.g. RCD.
9 NOTE: If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
9 Ensure that you inspect the transformer plug, cable and connections for wear and damage to ensure items are safe before connecting
them to the mains power supply. If worn or damaged DO NOT use.
WARNING! There are no user serviceable components in the transformer. DO NOT dismantle.
WARNING! For indoor use only. DO NOT allow the transformer to become wet. DO NOT use in wet or damp conditions.
8 DO NOT pull the transformer from the mains socket by the lead.
8 DO NOT overload this dryer stand; it should only be used for the designed purpose.
8 DO NOT locate in a position where items could fall from the dryer stand assembly owing to accidental contact.
2. INTRODUCTION
An integral, quiet running fan will quickly and conveniently dry and cool your helmet, boots or gloves whilst on the base. Inhibiting the
build-up of damp and odour. Helps prevent the build up of bacteria so your helmet, gloves and boots smell fresher. Improves the life span
of the linings and impact materials in your equipment. The unit comes is supplied with a USB adapter for connection to your vehicle or to
a portable power pack. Making it also ideal for race/track days, as well as a mains adaptor for using at home after your ride out/commute .
Made from a rm protective PU foam to best protect your equipment.
3. SPECIFICATION
UBH
4. OPERATION
See next page for Instructions and diagrams.
MS0815 Issue: 3 15/11/23
Model No: MS0815
Input: Mains adaptor:12V (dc) 3A. USB
adaptor: 5V (dc 2A)
Plug Type: 3-pin Transformer
© Jack Sealey Limited Original Language Version
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
REGISTER YOUR
PURCHASE HERE
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Second stage sub
assembly tted. Two
cones which are for
drying gloves or boots
Second stage sub
assembly showing
correct positioning of
the tubes
MS0815 Issue: 3 15/11/23
Transformer
connection
Dryer stand
assembly for use
to dry helmet
First stage sub
assembly.
