Loading ...
Loading ...
Loading ...
en Steam
20
Changing added steam
1.
Press
.
2.
Press "Added steam".
3.
Press the required steam intensity.
4.
Press to confirm the setting.
‒ If does not appear, the setting is applied im-
mediately.
Cancelling added steam
1.
Press
.
2.
Press "Added steam".
3.
Press "Off".
4.
Press to confirm the setting.
‒ If does not appear, the setting is applied im-
mediately.
a The operation continues without adding steam.
9.4 Steam jet
You can use "Steam boost" to specifically add intensive
steam at various intervals. This makes bread and bread
rolls in particular wonderfully crispy and gives them a
golden colour.
The appliance adds clouds of steam to the cooking
compartment for approximately 3 to 5 minutes. De-
pending on the operation, you can activate the steam
boost several times.
Types of heating and functions for steam boost
You can switch on steam boost for the following types
of heating and functions:
¡ "Circo Therm hot air"
¡ "Top/bottom heat"
¡ "Circo-roasting"
¡ "Bread baking setting"
¡ →"Meat probe", Page22
Switching on steam boost
1.
Fill the water tank.
→"Filling the water tank", Page17
2.
Press to switch the appliance on.
3.
Set a suitable type of heating.
→"Types of heating and functions for steam boost",
Page20
4.
Set a temperature above 120°C.
5.
Press "Steam boost".
6.
Press
to start operation with steam boost.
Once lights up, the water is heated up sufficiently
to use the steam boost.
Do not use the steam jet until the appliance has
completely heated up.
Note:If rapid heating is activated, the steam jet
can only be triggered once rapid heating is com-
plete.
7.
Press at the desired time.
a The steam jet is triggered and the appliance adds
clouds of steam to the cooking compartment for ap-
prox. 3 to 5 minutes.
a When the steam boost has finished, the operation
continues to run. Depending on the operation, the
steam jet can be triggered again if necessary.
a If the water tank runs dry during steam boost, "Fill
water tank" appears on the display. The operation
continues without steam boost.
→"Refilling the water tank", Page17
8.
When the food is ready, use
to switch the appli-
ance off.
9.
Empty the water tank and dry the cooking compart-
ment.
→"After using steam operation", Page20
9.5 After using steam operation
Dry the appliance after each steam operation.
Note:Traces of limescale may remain in the cooking
compartment after operation with steam. The functional-
ity of the appliance is not affected by this. You can re-
move traces of limescale using hot water or a cloth
soaked in vinegar. Observe the information on clean-
ing.
→"Cleaning and servicing", Page30
Emptying the water tank
WARNING‒Risk of burns!
The water tank may heat up while the appliance is in
operation.
▶ Wait until the water tank has cooled down from the
previous operation.
▶ Remove the water tank from the tank recess.
ATTENTION!
Drying the water tank in the hot cooking compartment
leads to damage to the water tank.
▶ Do not dry the water tank in the hot cooking com-
partment.
Cleaning the water tank in the dishwasher will damage
it.
▶ Do not clean the water tank in the dishwasher.
▶ Clean the water tank with a soft cloth and standard
washing-up liquid.
1.
Use
to open the control panel.
2.
Remove the water tank.
3.
Carefully remove the lid of the water tank.
4.
Empty the water tank, clean it with detergent and
then rinse it thoroughly with clean water.
5.
Dry all parts with a soft cloth.
6.
Rub the seal on the lid until dry.
7.
Leave the water tank to dry with the lid open.
8.
Place the lid on the water tank and push down on it.
9.
Insert the water tank and close the control panel.
Drying the condensation tray
WARNING‒Risk of burns!
The appliance becomes hot during operation.
▶ Allow the appliance to cool down before cleaning.
Requirement:The cooking compartment has cooled
down.
1.
Open the appliance door.
2.
Note:
The condensation tray is underneath the cooking
compartment.
Loading ...
Loading ...
Loading ...