Loading ...
Loading ...
Loading ...
© 2021 United States Stove Company
11
OPERATION INSTRUCTIONS
6. Materials containing asbestos;
7. Construction or demolition debris;
8. Railroad ties or pressure-treated wood;
9. Manure or animal remains;
10. Salt water driftwood or other previously salt
water saturated materials;
11. Unseasoned wood; or
12. Paper products, cardboard, plywood, or
particleboard. The prohibition against burning
these materials does not prohibit the use of re
starters made from paper, cardboard, saw dust,
wax and similar substances for the purpose
of starting a re in an affected wood heater.
Burning these materials may result in release of
toxic fumes or render the heater ineffective and
cause smoke.
UNIT PREPARATION
CAUTION:
• KEEP FOREIGN OBJECTS OUT OF THE
HOPPER.
• THE MOVING PARTS OF THIS HEATER ARE
PROPELLED BY HIGH TORQUE ELECTRIC
MOTORS. KEEP ALL BODY PARTS AWAY
FROM THE AUGER WHILE THE HEATER IS
PLUGGED INTO AN ELECTRICAL OUTLET.
THESE MOVING PARTS MAY BEGIN TO
MOVE AT ANY TIME WHILE THE HEATER IS
PLUGGED IN.
After properly installing your heater, you will need
to attach the electrical cord to the right side blower
housing rst; then plug it into a 110 Volt outlet (an
outlet surge protector is highly recommended).
PERFORMING AN INITIAL BURN
You must perform an initial burn in this appliance
before installing it in your home or garage.
This process is to ensure that the appliances is
functioning correctly, to cure the high temperature
paint and burn off any oil that is present in the sheet
metal components of the combustion chamber.
For the initial burn, only add a small amount of fuel,
approximately 4-5 lbs or about the amount to ll
a 2 lb coffee can. Operate the appliance on the 3
or 4 heat setting for approximately 30 minutes to
an hour. There will probably be a small amount
of smoke or fumes irradiating from the appliance
during this process. Follow the Start-Up procedure
below to begin your burn.
START-UP PROCEDURE
WARNING:
• DO NOT USE CHEMICALS OR FLUIDS TO
START THE FIRE; DO NOT BURN GARBAGE
OR FLAMMABLE FLUIDS SUCH AS
GASOLINE, NAPHTHA OR ENGINE OIL.
• HOT WHILE IN OPERATION. KEEP
CHILDREN CLOTHING AND FURNITURE
AWAY. CONTACT MAY CAUSE SKIN BURNS.
DO NOT TOUCH THE HOT SURFACES OF
THE HEATER. EDUCATE ALL CHILDREN ON
THE DANGERS OF A HIGH-TEMPERATURE
HEATER. YOUNG CHILDREN SHOULD BE
SUPERVISED WHEN THEY ARE IN THE
SAME ROOM AS THE HEATER.
• NEVER USE GASOLINE, GASOLINE-TYPE
LANTERN FUEL, KEROSENE, CHARCOAL
LIGHTER FLUID, OR SIMILAR LIQUIDS TO
START OR “FRESHEN UP” A FIRE IN THIS
HEATER. KEEP ALL SUCH LIQUIDS WELL
AWAY FROM THE HEATER WHILE IT IS IN
USE.
1. Verify that the hopper is clean and free of
foreign matter.
2. Fill the hopper with wood pellets; do not allow
any part of the bag or any other foreign material
into the hopper, as this may jam the auger.
3. Ensure that all pellet matter is cleared from the
hopper seating surface.
4. Close the hopper lid. The unit WILL NOT feed
fuel with the hopper lid open.
5. Verify that there is no pellet fuel, ash, or foreign
matter in the burn-pot before starting the
appliance.
6. Make sure that the viewing door and combustion
door is securely closed (the safety switch will not
allow the heater to feed fuel if they are left open.
7. Press the “ON” button on the control pad and
set the “heat RANGE” to your desired setting.
The ON light will be ashing and the light
corresponding with the heat setting will be
light.
Loading ...
Loading ...
Loading ...